ASTM F2178-2017b Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products《测定眼睛或者面部防护产品的耐电弧热性能和标准规格的标准试验方法》.pdf

《ASTM F2178-2017b Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products《测定眼睛或者面部防护产品的耐电弧热性能和标准规格的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2178-2017b Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products《测定眼睛或者面部防护产品的耐电弧热性能和标准规格的标准试验方法》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2178 17bStandard Test Method forDetermining the Arc Rating and Standard Specification forEye or Face Protective Products1This standard is issued under the fixed designation F2178; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method and product specification is used tomeasure the arc rating and specify the req

3、uirements forproducts intended for use as eye or face protection for workersexposed to electric arcs that would generate heat flux valuesfrom 84 to 25 120 kWm22 to 600 cal/cm2s. Products aretested as sold.1.2 This test method determines an arc rating for eye or faceprotective products. The faceshiel

4、d, safety spectacle, goggle oror other applicable portions of the complete product must meetANSI Z87.1. This excludes the textile or non ANSI Z87.1testable parts of the hood assemblies or other tested products.This standard does not measure optical and impact properties(seeANSI Z87.1) but does speci

5、fy requirements for optical andimpact properties.1.3 The materials covered by this standard are in the form offaceshields attached to the head by protective helmets (hardhats), headgear, hood assemblies, safety spectacles or goggles.Faceshields, safety spectacles or goggles are tested with orwithout

6、 other face and head protective products, for example,sock hoods, balaclavas, sweat shirt hoods or jacket hoods.1.3.1 Fabric layers used in the design of face protectionproducts such as in hood, neck guards, balaclava, shall meetthe requirements of Specification F1506. When fabrics aredesigned into

7、the protection provided for eye or face protectiveproducts, the arc rating of fabric system shall be determinedfirst by Test Method F1959/F1959M.1.3.2 The arc rating of the eye or face protective productwhich requires fabric to provide protection to the face or headwill not be higher than the lower

8、arc rating of either the fabricsystem or the shield/visor assembly.1.4 This test method shall be used to measure and describethe properties of materials, products, or assemblies in responseto convective and radiant energy generated by an electric arcunder controlled laboratory conditions and does no

9、t purport topredict damage from light other than the thermal aspectsmeasured.1.5 The values stated in SI units shall be regarded asstandard except as noted. Within the text, alternate units areshown in brackets.The values stated in each system may not beexact equivalents; therefore, alternate system

10、s must be usedindependently of the other. Combining values from the systemsdescribed in the text may result in nonconformance with themethod.1.6 This standard does not purport to describe or appraisethe effect of the electric arc fragmentation explosion andsubsequent molten metal splatter, which inv

11、olves the pressurewave containing molten metals and possible fragments of othermaterials except to the extent that heat energy transmission dueto these arc explosion phenomena is reduced by test specimens.1.7 This standard shall not be used to describe or appraisethe fire hazard or fire risk of mate

12、rials, products, or assembliesunder actual fire conditions. However, results of this test maybe used as elements of a fire assessment which takes intoaccount all of the factors which are pertinent to an assessmentof the fire hazard of a particular end use.1.8 This standard does not purport to addres

13、s all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.Forspecific precautions, see Section 7.1.9

14、This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Tra

15、de (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:21This test method is under the jurisdiction of ASTM Committee F18 onElectrical Protective Equipment for Workers and is the direct responsibility ofSubcommittee F18.65 on Wearing Apparel.Current edition approved Oct. 1, 2017. Published Nov

16、ember 2017. Originallyapproved in 2002. Last previous edition approved in 2017 as F2178 17a. DOI:10.1520/F2178-17B.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to t

17、he standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in

18、the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1C177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties by Means ofthe Guarde

19、d-Hot-Plate ApparatusD123 Terminology Relating to TextilesD3776 Test Methods for Mass Per Unit Area (Weight) ofFabricD4391 Terminology Relating to The Burning Behavior ofTextilesE457 Test Method for Measuring Heat-Transfer Rate Usinga Thermal Capacitance (Slug) CalorimeterF1494 Terminology Relating

20、to Protective ClothingF1506 Performance Specification for Flame Resistant andArc Rated Textile Materials for Wearing Apparel for Useby Electrical Workers Exposed to Momentary ElectricArcand Related Thermal HazardsF1958/F1958M Test Method for Determining the Ignitabil-ity of Non-flame-Resistant Mater

21、ials for Clothing byElectric Arc Exposure Method Using MannequinsF1959/F1959M Test Method for Determining theArc Ratingof Materials for Clothing2.2 ANSI/IEEE Standards:IEEE Standard Dictionary of Electrical and ElectronicsTerms3ANSI Z87.1-2003 Practice for Occupational and Educa-tional Eye and Face

22、Protection43. Terminology3.1 DefinitionsFor definitions of other textile terms usedin this method, refer to terminology in Terminology D123,D4391, F1494 and the IEEE Standard Dictionary of Electricaland Electronics Terms.3.2 Definitions of Terms Specific to This Standard:3.2.1 afterflame, npersisten

23、t flaming of a material after theignition source has been removed.3.2.2 afterflame time, nthe length of time for which amaterial continues to flame after the ignition source has beenremoved.3.2.3 arc duration, ntime duration of the arc, s.3.2.4 arc energy, vi dt, nsum of the instantaneous arcvoltage

24、 values multiplied by the instantaneous arc currentvalues multiplied by the incremental time values during thearc, J.3.2.5 arc gap, ndistance between the arc electrodes, cmin.3.2.6 arc rating, nvalue attributed to materials that de-scribes their performance to exposure to an electric arcdischarge, J

25、/cm2(calcm2).3.2.6.1 DiscussionThe arc rating is expressed inJ/cm2(calcm2) and is derived from the determined value ofATPV or EBT(should a material system exhibit a breakopenresponse below the ATPV value).3.2.7 arc thermal performance value (ATPV), nthe inci-dent energy of a fabric or material that

26、results in 50 %probability that sufficient heat transfer through the specimen ispredicted to cause the onset of a second-degree skin burn injurybased on the Stoll curve, kW/m2cal/cm2.53.2.8 arc voltage, nvoltage across the gap caused by thecurrent flowing through the resistance created by the arc ga

27、p(V).3.2.9 asymmetrical arc current, nthe total arc currentproduced during closure; it includes a direct component and asymmetrical component, A.3.2.10 blowout, nthe extinguishing of the arc caused by amagnetic field.3.2.11 breakopen, nin electric arc testing, a materialresponse evidenced by the for

28、mation of one or more holes inthe material which may allow thermal energy to pass throughmaterial.3.2.11.1 DiscussionThe specimen is considered to exhibitbreakopen when any hole in the material or fabric is at least 1.6cm20.5 in.2 in area or at least 2.5 cm 1.0 in. in anydimension. For textile mater

29、ials, single threads across theopening or hole do not reduce the size of the hole for thepurposes of this test method. In multiple layer specimens, ifsome of the layers are ignitable, breakopen occurs when theselayers are exposed.3.2.12 breakopen threshold energy (EBT), nthe incidentenergy on a fabr

30、ic or material that results in a 50 % probabilityof breakopen.3.2.12.1 DiscussionThis is the value in J/cm2calcm2determined by use of logistic regression analysis representingthe energy at which breakopen of the layer occurred.3.2.13 deformation, nfor electric arc testing of eye or faceprotective pr

31、oducts, the sagging of material greater than 7.6 cm3 in. or melting in any manner that the faceshield/windowtouches any part of the body.3.2.14 dripping, nin electric arc testing, a material re-sponse evidenced by flowing of a specimens material ofcomposition.3.2.14.1 DiscussionDripping is exhibited

32、 by either thefabric material or faceshield material, or other parts of eye orface protective products.3.2.15 electric arc ignition, nin electric arc testing of eyeor face protective products, the initiation of combustion asrelated to electric arc exposure, a response that causes theignition of text

33、ile test specimen material which is accompaniedby heat and light, and then subsequent burning for at least 5 s,and consumption of at least 25 % of the test specimen area.3.2.15.1 DiscussionFor multilayer specimens, consump-tion of the innermost FR layer must be at least 25 %.3Available from Institut

34、e of Electrical and Electronics Engineers, Inc. (IEEE),445 Hoes Ln., P.O. Box 1331, Piscataway, NJ 08854-1331, http:/www.ieee.org.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.5Derived from Stoll,A. M., and Chianta, M.A

35、., “Method and Rating System forEvaluations of Thermal Protection,” Aerospace Medicine , Vol 40, 1969, pp.1232-1238 and Stoll, A. M., and Chianta, M. A., “Heat Transfer through Fabrics asRelated to Thermal Injury,” TransactionsNew York Academy of Sciences, Vol 33(7), Nov. 1971, pp. 649-670.F2178 17b

36、23.2.16 faceshield, na protective device commonly in-tended to shield the wearers face, or portions thereof, inaddition to the eyes, from certain hazards.3.2.17 heat flux, nthe thermal intensity indicated by theamount of energy transmitted per area and timeW/m2calcm2s.3.2.18 i2t, nsum of the instant

37、aneous arc current valuessquared multiplied by the incremental time values during thearc, A2/s.3.2.19 incident energy monitoring sensors, nsensorsmounted on each side of each head, using calorimeters, notcovered by specimens, used to measure incident energy.3.2.20 incident exposure energy (Ei), nin

38、arc testing, thetotal incident energy delivered to monitor calorimeter sensorsas a result of the arc exposure, J/cm2calcm2.3.2.20.1 DiscussionIn an arc test exposure, incident ex-posure energy for a specimen is determined from the averageof the measured incident energy from the respective twomonitor

39、 sensors adjacent to the test specimen.3.2.21 material response, nmaterial response to an elec-tric arc is indicated by the following terms: breakopen, melting,dripping, deformation, afterflame time, shrinkage, and electricarc ignition.3.2.22 melting, nin arc testing, a material response evi-denced

40、by softening of the material.3.2.23 peak arc current, nmaximum value of the AC arccurrent, A.3.2.24 RMS arc current, nroot mean square of the AC arccurrent, A.3.2.25 shrinkage, nin testing eye or face protectiveproducts, a material response evidenced by reduction inspecimen size.3.2.26 Stoll curve,

41、nan empirical predicted second-degreeskin burn injury model, also commonly referred to as the StollResponse.3.2.27 X/R ratio, nthe ratio of system inductive reactanceto resistance. It is proportional to the L/R ratio of time constant,and is, therefore, indicative of the rate of decay of any DCoffset

42、. A large X/R ratio corresponds to a large time constantand a slow rate of decay.4. Summary of Test Method4.1 This test method determines the heat transport responseacross a material, fabric, or fabric system when exposed to theheat energy from an electric arc. This heat transport response isassesse

43、d versus the Stoll curve, an approximate human tissuetolerance predictive model that projects the onset of a second-degree burn injury.4.1.1 Products are mounted on the standard mannequin headcontaining copper slug calorimeters inserted in the eyes,mouth, and chin positions. During this procedure, t

44、he amountof heat energy transferred by the specimen eye or faceprotective products is measured during and after exposure to anelectric arc.4.1.2 The thermal energy exposure and heat transport re-sponse of the test specimen(s) are measured with copper slugcalorimeters. The change in temperature versu

45、s time is used,along with the known thermo-physical properties of copper todetermine the respective thermal energies delivered to andthrough the specimen(s).4.2 This procedure incorporates incident energy monitoringsensors.4.3 Product and material performance for this procedure aredetermined by comp

46、aring the amount of thermal energygenerated by the arc flash on monitor sensors with the energytransferred by or through the test specimen(s) and measured bysensors on the mannequin head.4.4 Product and material responses shall be further de-scribed by recording the observed effects of the electric

47、arcexposure on the specimens using the terms in the Reportsection.5. Significance and Use5.1 This test method is intended for the determination of thearc rating of a product/design, intended for use as eye or faceprotection for workers exposed to electric arcs.5.1.1 Because of the variability of the

48、 arc exposure, differ-ent heat transmission values may be observed at individualsensors. The results of each sensor are evaluated in accordancewith Section 12.5.2 This test method maintains the specimen in a static,vertical position and does not involve movement except thatresulting from the exposur

49、e.5.3 This test method specifies a standard set of exposureconditions. Different exposure conditions may produce differ-ent results.5.4 This specification covers the minimum performancecriteria for arc resistance and other requirements for eye or faceprotective products used by workers who may be exposed tothermal hazards of momentary electric arcs or flame.5.5 The purchaser has the option to perform or haveperformed any of these tests in order to verify the performanceof the eye or face protective product. Claims for f