ASTM F1942-1998(2003) Standard Practice for Creating Test Targets for Determining the Ink Yield of the Imaging Supplies Used in Ink Jet Printers《创建测定喷墨打印机用成像供给的油墨成品的试验目标的标准操作规程》.pdf

《ASTM F1942-1998(2003) Standard Practice for Creating Test Targets for Determining the Ink Yield of the Imaging Supplies Used in Ink Jet Printers《创建测定喷墨打印机用成像供给的油墨成品的试验目标的标准操作规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1942-1998(2003) Standard Practice for Creating Test Targets for Determining the Ink Yield of the Imaging Supplies Used in Ink Jet Printers《创建测定喷墨打印机用成像供给的油墨成品的试验目标的标准操作规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1942 98 (Reapproved 2003)Standard Practice forCreating Test Targets for Determining the Ink Yield of theImaging Supplies Used in Ink Jet Printers1This standard is issued under the fixed designation F 1942; the number immediately following the designation indicates the year oforiginal

2、adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes a method for creating test targetscontainin

3、g varying percentages of area coverage for use indetermining the yield of the supplies used by liquid and solidink jet printers.1.2 This standard may involve hazardous materials, opera-tions and equipment. This standard does not purport to addressall of the safety concerns, if any, associated with i

4、ts use. It isthe responsibility of the user of this standard to establishappropriate safety and health practices and determine limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2F 909 Terminology Relating to Printers3. Terminology3.1 Definitions:3.1.1 percent area coveragethe amoun

5、t of area on agiven-size page which is covered with an image produced frombusiness imaging products (expressed in percent coverage).3.2 See Terminology F 909 for definitions of terms relatingto computer printers.4. Summary of Practice4.1 The test targets which are created using this practice areused

6、 to determine the page or ink yield (in in.2/g of ink) of inkjet printer supplies.4.2 The test targets may be generated by a printer, verifiedfor percentage of area coverage, and used to determine thepage yield of ink jet printer supplies.4.3 With this information, the user can determine supply-yiel

7、d information for purposes of competitive comparisons orthe determination of cost-per-page.4.4 The test targets which are created using this practice canbe used to calibrate the equipment used to verify percent areacoverage.5. Significance and Use5.1 Test targets where the percentage of area coverag

8、e hasbeen predetermined are not readily available from commercialsources. Moreover, it is beyond the ability of most users toverify if indeed, the commercially-available test targets containthe advertised area coverage. This procedure allows the user toeasily create test targets, using commercially

9、available PCsoftware, which can be easily verified for percentage of areacoverage and can provide reproducible interlaboratory results.6. Interferences6.1 Consider the resolution of the ink jet printer for whichthe test target is being created. In other words, size theelements so that they can be di

10、vided evenly by the resolutionof the printer. This will ensure that the printer will only outputentire pixels, and will not be forced to use resolution enhance-ment techniques, such as modulation of the pixel size.6.2 When creating the elements in the test target, considerthe aperture size of the de

11、nsitometer which will be used tomeasure the output density. The elements created shouldcomfortably fit within the densitometer aperture area.7. Apparatus7.1 Personal computer and ink jet printer.7.2 Personal-computer word processing or page layout(desktop publishing) software, which allows the user

12、to specifythe size, create, copy and place graphic elements on a page.8. Creating the Test Target8.1 Determine the intended test target percent area cover-age. For example, the current industry-accepted area coverageis 5 % area coverage for black- and -white images and 15 % forfull-color images.1Thi

13、s practice is under the jurisdiction of ASTM Committee F05 on BusinessCopy Products and is the direct responsibility of Subcommittee F05.07 on Ink JetImaging Products.Current edition approved Dec. 10, 1998. Published February 1999.2For referenced ASTM standards, visit the ASTM website, www.astm.org,

14、 orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.8.2 Determine t

15、he number and dimensions of elementsrequired for the application. Although only one element isrequired, it may be desirable to arrange several smallerelements around the page to produce areas suitable for densi-tometer measurement within the test target (refer to Fig. 1).8.3 Create a new document wi

16、th a word processor ordesktop publishing software program.8.4 Access the drawing tools and create an element with theproper dimensions.8.4.1 Some programs provide a dialog box which allows theuser to enter the dimension from the keyboard.8.5 Using the software, specify the color of the element(cyan,

17、 yellow, magenta or black).8.6 If necessary, use the software to copy the element therequired number of times and arrange the elements on the page.8.6.1 Do not place elements within the unprintable area ofthe intended printer. This area is usually from 0.3 in. to 0.55 in.around the perimeter of the

18、page depending on the printer;consult the printer manual for details.9. Keywords9.1 imaging supplies; ink jet; ink jet printer; ink yield; testtargetF 1942 98 (2003)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin thi

19、s standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be

20、 reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresp

21、onsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, We

22、st Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).FIG. 1 Sample Test TargetF 1942 98 (2003)3