ASTM F1074-1987(2002) Standard Specification for Cleats Welded Horn Type《焊接喇叭型绳栓规范》.pdf

《ASTM F1074-1987(2002) Standard Specification for Cleats Welded Horn Type《焊接喇叭型绳栓规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1074-1987(2002) Standard Specification for Cleats Welded Horn Type《焊接喇叭型绳栓规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1074 87 (Reapproved 2002)An American National StandardStandard Specification forCleats, Welded Horn Type1This standard is issued under the fixed designation F 1074; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers hollow cleats and pads formarine use.1.2 The cleats shall be used where securing o

3、f boat handlinglines are required onboard commercial and navy boats andcrafts.1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Documents2.1 ASTM Standards:A 36/A 36M Specification for Carbon Structural

4、Steel2A 370 Test Methods and Definitions for Mechanical Testingof Steel Products3A 385 Practice for Providing High-Quality Zinc Coatings(Hot-Dip)43. Ordering Information3.1 Orders for material under this specification shall includethe following:3.1.1 Title, number, and date of this specification,3.1

5、.2 Quantity,3.1.3 Size of cleats, and3.1.4 Packaging, packing, or marking requirements.4. Materials and Manufacture4.1 Material:4.1.1 The horn cleats shall be of galvanized steel, grade1023W, in accordance with Practice A 385.4.1.2 The base plate shall be of steel, (carbon 0.35 maxi-mum), in accorda

6、nce with Specification A 36/A 36M.4.1.3 All chafing surfaces shall have a 125 finish.4.2 ManufactureThe cleats horns shall be of cast steel,round in shape, and free of burrs or sharp edges. The hornsshall be welded to a base plate as shown in Fig. 1 (see Table 1).The weld is to be ground smooth to p

7、revent chafing of ropes.The base plate shall be oval shaped with smooth roundededges. The dimensions shall be in accordance with Table 1.5. Packaging5.1 The packing shall afford protection against deteriorationand physical damage during shipment from the manufacturer tothe using activity for immedia

8、te use.6. Product Marking6.1 Containers shall be stenciled with the ASTM standarddesignation, in black paint with approximately 1 in. (25.4 mm)high letters and numbers with the following information:6.1.1 Address,6.1.2 purchase order number, and6.1.3 Manufacturers name.7. Keywords7.1 base plates; bo

9、at handling lines; cleats; hollow cleats;horn cleats; marine; marine cleats; ship; welded cleats1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting.Current edition approved Aug. 28, 198

10、7. Published October 1987.2Annual Book of ASTM Standards, Vol 01.04.3Annual Book of ASTM Standards, Vol 01.03.4Annual Book of ASTM Standards, Vol 01.06.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.NOTESee Table 1 for dimensions.FI

11、G. 1 Welded Horn Type Cleat (16 in.)F 10742SUPPLEMENTARY REQUIREMENTSThe following supplementary requirement shall apply only when specified by the purchaser in thecontract or order.S1. Quality Assurance ProvisionsS1.1 Responsibility for InspectionThe purchaser reservesthe right to perform any of th

12、e inspections set forth in thespecification where such inspections are deemed necessary toassure that supplies and services conform to prescribed require-ments.S1.2 Source InspectionThe purchaser reserves the rightto inspect the manufacturing process and end product in thesuppliers plant.S1.3 TestsT

13、he cleats shall meet the test load requirementsof Table 1, as tested in accordance with Test Methods andDefinitions A 370.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expre

14、ssly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised

15、, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may a

16、ttend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States

17、. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Welded Horn-Type Cleat DimensionsNOTE 1Table 1 is t

18、o be used with Fig. 1.NOTE 21 in. = 25.4 mm.NOTE 31 lb = 0.45 kg.Cleat Rope Circumference (in.)Rope Di-ameter(in.)Cleats TestLoad (lb)Dimensions (in.)Calcu-latedWeight(lb)Manila Nylon DacronPolypro-pylene6 3 37 Fi-berCore WireRopeABCDEFGHJKLMN10 212 178 318 11453258 1332 17851614716 2 5.3 134 11112 410016 4 3 5 214 1134 31271634 314 21.7 3 2 2 212516 900024 6 412 712 338 112 258 4123434 118 412 75 5 3 3 412 23 00030 712 558 938 3341532 178 3932 558151678 1516 512 137 6 312 4558 36 000F 10743