ASTM F1073-1987(2007) Standard Specification for Door Fittings for Watertight Gastight Airtight Weathertight and Non-Tight Doors for Marine Use《船用水密 气密 不透气、防风雨和无夹扣门门配件的标准规范》.pdf

《ASTM F1073-1987(2007) Standard Specification for Door Fittings for Watertight Gastight Airtight Weathertight and Non-Tight Doors for Marine Use《船用水密 气密 不透气、防风雨和无夹扣门门配件的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1073-1987(2007) Standard Specification for Door Fittings for Watertight Gastight Airtight Weathertight and Non-Tight Doors for Marine Use《船用水密 气密 不透气、防风雨和无夹扣门门配件的标准规范》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1073 87 (Reapproved 2007)An American National StandardStandard Specification forDoor Fittings, for Watertight /Gastight /Airtight,Weathertight, and Non-Tight Doors, for Marine Use1This standard is issued under the fixed designation F 1073; the number immediately following the designat

2、ion indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the pri

3、ncipal design and typeof material for manufacturing fittings for watertight/gastight/airtight, weathertight, and non-tight doors, for marine use. Notethat “gastight” is commercial terminology which also means“airtight” in naval terminology.1.2 The fittings are intended for use on all doors for marin

4、euse, except joiner and expanded metal doors.2. Referenced Documents2.1 ASTM Standards:2A 36/A 36M Specification for Carbon Structural SteelA 240/A 240M Specification for Chromium andChromium-Nickel Stainless Steel Plate, Sheet, and Stripfor Pressure Vessels and for General ApplicationsA 276 Specifi

5、cation for Stainless Steel Bars and ShapesA 563 Specification for Carbons and Alloy Steel NutsA 668/A 668M Specification for Steel Forgings, Carbonand Alloy, for General Industrial UseB 140/B 140M Specification for Copper-Zinc-Lead (RedBrass or Hardware Bronze) Rod, Bar, and ShapesB 210 Specificatio

6、n for Aluminum and Aluminum-AlloyDrawn Seamless Tubes2.2 Military Standards:3MIL-P-24441 Epoxy-Polyamide PaintMIL-P-17578A Packing Material, Plastic (for Dogs forWatertight Closures) (Symbol 1425)MIL-C-81706 Coating, Aluminum and Aluminum AlloysDOD-STD-2138 Metal Sprayed Coating Systems for Cor-rosi

7、on Protection2.3 Federal Specifications:3QQ-C-390 Copper Alloy CastingsTT-E-490 Enamel-Silicone Alkyd Copolymer, Semi-gloss,Exterior2.4 ANSI Standard:A2.6 Standard for Fire Tests of Window Assemblies42.5 AISI Standard:316 Low Alloy Stainless Steel (Cres 316)53. Classification3.1 The dogs and hinges

8、shall be classified as given in Table1.4. Ordering Information4.1 Ordering for fittings shall be indicated on the purchaseorder prepared for doors, with reference to this specificationnoted.4.2 When ordering fittings, indicate the following:4.2.1 Type,4.2.2 Quantity,4.2.3 Marking (see Section 8), an

9、d4.3 Inspection and acceptance of fittings shall be agreedupon between the purchaser and the supplier.5. Materials and Manufacture5.1 The material shall be as specified in Tables 2-4.5.2 All securing screws and fasteners shall be of stainlesssteel, Type 316.5.3 All glazing in portlights of fire door

10、 shall meet ANSIA2.6.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Aug. 1, 2007. Published August 2007. Originallyapproved in 1987. Las

11、t previous edition approved in 1999 as F 1073 - 87(1999).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Ava

12、ilable from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.5Available from America

13、n Iron and Steel Institute (AISI), 1140 ConnecticutAve., NW, Suite 705, Washington, DC 20036, http:/www.steel.org.TABLE 1 Classification of Dogs and HingesType DescriptionDog:A Fitted to doorB Fitted to door frameHinge:A With clenched pinB With clenched pin secured with cotter pin1Copyright ASTM Int

14、ernational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.TABLE 2 Material for Door DogsComponentMild Steel Aluminum Glass-Reinforced PlasticNumber Item1 Handle interior Specification A 668 Specification A 668 Specification A 6682 Handle exterior Specification A

15、 668 Specification A 668 Specification A 6683 Jam nut Specification A 563 Specification A 563 Specification A 2764 Spring washer steel commercial AISI (316)AIS(316)5 Washer steel commercial steel commercial steel commercial6 Dog sleeve Specification A 36/A 36M Specification B 210 (AL-5086) Specifica

16、tion B 210 (AL 5086)7 Bushing oil impregnated bronze oil impregnated bronze oil impregnated bronze8 Packing MIL-P-17578A MIL-P-17578A MIL-P-17578A9 Packing gland MIL-P-17578A MIL-P-17578A MIL-P-17578A10 Grease fitting Specification B 140/B 140M Specification B 140/B 140M Specification B 140/B 140M11

17、 Wedge QQ-C-390 Specification B 210 QQ-C-390TABLE 3 Material for Door HingesComponentMild Steel Aluminum Glass-Reinforced PlasticNumber Item1 Piece to frame Specification A 36/A 36M Specification A 240/A 240M Specification A 240/A 240M2 Piece to door Specification A 36/A 36M Specification A 240/A 24

18、0M Specification A 240/A 240M3 Clenched pin corrosion-resistant steel (316) corrosion-resistant steel (316) corrosion-resistant steel (316)4 Washer corrosion-resistant steel (commercial) corrosion-resistant steel (commercial) corrosion-resistant steel (commercial)5 Cotter pin corrosion-resistant ste

19、el (commercial) corrosion-resistant steel (commercial) corrosion-resistant steel (commercial)TABLE 4 Material for Miscellaneous Fittings Door MaterialComponentMild Steel Aluminum Glass-Reinforced PlasticNumber Item1 Port light Specification A 240/A 240M Specification A 240/A 240M Specification A 240

20、/A 240M2 Label plate Specification A 240/A 240M Specification A 240/A 240M Specification A 240/A 240M3 Hasp and eye Specification A 276 Specification A 276 Specification A 2764 Hold back hook Specification A 276 Specification A 276 Specification A 2765 Grab handle Specification A 276 Specification A

21、 276 Specification A 2761 in. = 25.4 mm2.2 lb = 1 kgFIG. 1 Watertight, Airtight, and Weathertight Door Dog Assembly (Estimated Weight 8 lb)F 1073 87 (2007)26. Construction, Shape, and Dimensions6.1 The construction, shape, and dimensions for dogs andhinges shall be as shown in Figs. 1-9.6.2 Door dog

22、s shall be supplied with hold-open clips.7. Workmanship, Finish, and Appearance7.1 All materials shall have a smooth finish.7.2 Pretreatment and priming of door fittings shall be asfollows:7.2.1 Mild steel fittings shall be abrasive blasted to “nearwhite” metal and coated with inorganic zinc silicat

23、e at 1.5 to3.0 mils.7.2.2 Steel fittings, secured on doors, shall be welded tosteel; whereas aluminum fittings when secured to aluminum orglass-reinforced plastic doors, shall be welded or bolted intoposition.7.2.3 Nonferrous fittings shall be either riveted or bolted toaluminum, steel or glass-rein

24、forced plastic doors, or combina-tion thereof.7.2.4 Where different metals are to be used, insulation shallbe used between them, in way of contact, to prevent galvanicaction.8. Product Marking8.1 Each fitting shall be marked with its purchase ordernumber and shall indicate the type of fitting, left

25、hand or righthand. The marking shall be applied on a waterproof tag andattached to the fitting.9. Keywords9.1 airtight; door fittings; doors; gastight; marine; non-tight;ship; tightness integrity; watertight; weathertight1 in. = 25.4 mm2.2 lb = 1 kgFIG. 2 Dog DetailsF 1073 87 (2007)31 in. = 25.4 mm2

26、.2 lb = 1 kgFIG. 3 Dog Assembly for Non-Tight Doors (Estimated Weight 8 lb)1 in. = 25.4 mm2.2 lb = 1 kgFIG. 4 Hinge Assembly for Non-Tight DoorsF 1073 87 (2007)41 in. = 25.4 mmFIG. 5 Hook Staple Detail1 in. = 25.4 mmFIG. 6 Grabhandle DetailF 1073 87 (2007)51 in. = 25.4 mmFIG. 7 Frame Assembly Fixed

27、Light1 in. = 25.4 mmFIG. 8 Hasp and Eye Assembly “A”F 1073 87 (2007)6SUPPLEMENTARY REQUIREMENTSThe following supplementary requirement shall apply only when specified by the contract or order.S1. PaintingS1.1 Pretreatment and priming of mild steel door compo-nents shall consist of metal spray coatin

28、g in accordance withDOD-STD-2138, Type II on both sides before assembly.S1.2 Aluminum door components shall be treated with achemical conversion coating MIL-C-81706, followed with asecond coat of epoxy polyamide primer (formula 150 ofMIL-P-24441) alkyd haze gray (TT-E-490) or equal. Coatingto be app

29、lied before assembly, following surface preparation,in accordance with the manufacturers instructions.S1.3 Special heat resisting gaskets, in accordance withMIL-P-17578A, are to be used.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any

30、item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical c

31、ommittee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at

32、a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Dr

33、ive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).1 in. = 25.4 mmFIG. 9 Hinge Assembly for Aluminum DoorsF 1073 87 (2007)7