ASTM A918-2006 Standard Specification for Steel Sheet Zinc-Nickel Alloy Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surfac.pdf
《ASTM A918-2006 Standard Specification for Steel Sheet Zinc-Nickel Alloy Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surfac.pdf》由会员分享,可在线阅读,更多相关《ASTM A918-2006 Standard Specification for Steel Sheet Zinc-Nickel Alloy Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surfac.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: A 918 06Standard Specification forSteel Sheet, Zinc-Nickel Alloy Coated by the ElectrolyticProcess for Applications Requiring Designation of theCoating Mass on Each Surface1This standard is issued under the fixed designation A 918; the number immediately following the designation indica
2、tes the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers zinc-nickel allo
3、y coatingsapplied by the electrolytic process to hot-rolled and cold-rolledsteel sheet. The coating has a smooth, spangle-free surface. Thezinc-nickel-coated sheet covered in this specification is pro-duced in a range of coating masses to provide coatings that arecompatible with the anticipated serv
4、ice life required. Thecoating mass varies, from very thin coatings that are usuallypainted to provide good service, to relatively heavy masses thatprovide good corrosion resistance in the bare (unpainted)condition. The composition range is from 9 to 16 % nickel, byweight, with the balance being zinc
5、.1.2 The product shall be coated on one or both surfaces withequal or differential coating masses on the two surfaces. Sheetcoated with equal coating masses on each surface has similarlevels of corrosion protection on each surface. Often, however,a higher level of corrosion protection is required on
6、 one surfacethan is required on the other. In these situations, one surfaceshall be specified with a heavier coating mass than the other.Either surface, when specified to be painted, will provideadditional corrosion protection as compared to an unpaintedsurface.1.3 This coating process has essential
7、ly no effect on the basemetal mechanical properties, and use is permitted on any gradeof hot- or cold-rolled steel sheet. The coated sheet is availableas Commercial Steel (CS), Drawing Steel (DS), Deep DrawingSteel (DDS), Extra-Deep Drawing Steel (EDDS), StructuralSteel (SS), High-Strength Low-Alloy
8、 Steel (HSLAS), High-Strength Low-Alloy Steel with Improved Formability(HSLAS-F), Solution-Hardened Steel (SHS), or Bake-Hardenable Steel (BHS).1.4 The values stated in SI units are to be regarded as thestandard.2. Referenced Documents2.1 ASTM Standards:2A 754/A 754M Test Method for Coating Weight (
9、Mass) ofMetallic Coatings on Steel by X-Ray FluorescenceA 917 Specification for Steel Sheet, Coated by the Electro-lytic Process forApplications Requiring Designation of theCoating Mass on Each Surface (General Requirements)E 1659 Test Methods for Coating Weight and ChemicalAnalysis of Zinc-Nickel A
10、lloy Electrolytically Coated onSteel Sheet3. Classification3.1 Coatings shall be designated as in Specification A 917.The letter N shall be used to designate zinc-nickel coatings.4. Ordering Information4.1 Orders for products to this specification shall include thefollowing information, as necessary
11、 to adequately describe thedesired product:4.1.1 Name of product (electrolytic zinc-nickel alloy-coatedsteel sheet).4.1.2 ASTM designation and year of issue.4.1.3 Base metal type (hot rolled or cold rolled).4.1.4 Base metal designation Commercial Steel (CS),Drawing Steel (DS), Deep Drawing Steel (DD
12、S), Extra-DeepDrawing Steel (EDDS), High-Strength Low-Alloy Steel(HSLAS), High-Strength Low-Alloy with Improved Formabil-ity (HSLAS-F), Solution-Hardened Steel (SHS), or Bake-Hardenable Steel (BHS).4.1.5 Formability type, strength, grade, or class, or combi-nation thereof, as required for structural
13、 or high-strengthlow-alloy steels.4.1.6 Coating designation (see 3.1).4.1.7 Surface treatments required (see Note 1).1This specification is under the jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and is the direct responsibility ofSubcommittee A05.11 on Sheet Specifica
14、tions.Current edition approved Nov. 1, 2006. Published December 2006. Originallyapproved in 1993. Last previous edition approved in 2005 as A 918 00 (2005).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of AST
15、MStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.NOTE 1Steel sheet is ava
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMA9182006STANDARDSPECIFICATIONFORSTEELSHEETZINCNICKELALLOYCOATEDBYTHEELECTROLYTICPROCESSFORAPPLICATIONSREQUIRINGDESIGNATIONOFTHECOATINGMASSONEACHSURFACPDF

链接地址:http://www.mydoc123.com/p-459962.html