SAE J 2839-2010 Heavy Duty High Speed Datalink Connector《重型高速数据联络系统连接》.pdf

《SAE J 2839-2010 Heavy Duty High Speed Datalink Connector《重型高速数据联络系统连接》.pdf》由会员分享，可在线阅读，更多相关《SAE J 2839-2010 Heavy Duty High Speed Datalink Connector《重型高速数据联络系统连接》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 _ 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSX EOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDO and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, LVWKHVROHUHVS

2、RQVLELOLWRIWKHXVHU SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced

3、, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776

4、-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J2839_201507 SURFACE VEHICLE RECOMMENDED PRACTICE J2839 JUL2015 Issued 2010-02 Reaffirmed 2015-07 Superseding

5、 J2839 FEB2010 Heavy Duty High Speed Datalink Connector RATIONALE J2839 has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE This SAE Recommended Practice defines the performance requirements, size and mating interfaces for M12 style 4 and 5 pole Heavy Duty High Speed Datalin

6、k connection systems, and applies to both cable-to-cable and cable-to-device connectors. 1.1 Purpose High Speed Datalink connection systems, typically those operating at speeds that are greater than 10M bps, have been developed for commercial applications without regard to their potential applicatio

7、n on heavy-duty vehicles or off-highway machines. This recommended practice is intended to be the standard for the heavy-duty connector mating interface and environmental performance requirements for High Speed Datalink connection systems. This standardization will assure mating compatibility of dat

8、a link connectors from multiple connector suppliers while meeting industry performance requirements for heavy-duty applications. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest

9、issue of SAE publications shall apply. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. SAE J1128 Low Voltage Primary Cable SAE J2030 Heavy-Duty Electrical

10、 Connector Performance Standard SAE INTERNATIONAL J2839 Reaffirmed JUL2015 Page 2 of 8 2.1.2 IEC Publications Available from International Electrotechnical Commission, 3, rue de Varembe, P.O. Box 131, 1211 Geneva 20, Switzerland, Tel: +44-22-919-02-11, www.iec.ch. IEC 61076-2-101 Connectors for elec

11、tronic equipment Product requirements Part 2-101: Circular connectors Detail specification for M12 connectors with screw-locking 2.1.3 ISO Publications Available from American National Standards Institute, 25 West 43rd Street, New York, NY 10036-8002, Tel: 212-642-4900, www.ansi.org. ISO 6722 Road v

12、ehicles 60 V and 600 V single core cables Dimensions, test methods and requirements ISO 20653 Road vehicles Degrees of protection (IP-Code) Protection of electrical equipment against foreign objects, water and access 3. DEFINITIONS 3.1 BULKHEAD CONNECTOR The panel mount electrical connector which el

13、ectrically and mechanically joins the circuitry of a component or cable to another electrical connector. 3.2 CABLE CONNECTOR The cable side of an electrical connector which electrically and mechanically joins a cable to another electrical connector. 3.3 DEVICE MOUNTED CONNECTOR The device side of an

14、 electrical connector which electrically and mechanically joins the circuitry of a component to another electrical connector. 3.4 HDM12 A heavy duty M12 connector per IEC 61076-2-101 that also meets the requirements of SAE J2839. 3.5 HDM12EX An HDM12 connector with the additional physical durability

15、 as defined within SAE J2839. 4. REQUIREMENTS 4.1 Physical Requirements J2839 HDM12 connectors shall mate to IEC 61076-2-101 M12 connectors and will meet at minimum the performance requirements of IEC 61076-2-101 with the following exceptions: 4.1.1 The application torque requirement for the M12 thr

16、eads is 0.8 to 1.0 Nm. The torque requirement of the HDM12EX version M24-2 threads shall be 25 to 35 Nm. 4.1.2 The J2839 connector wire terminals shall be capable of being terminated to 0.8 mm2 (18 AWG) or 0.5 mm2 (20 AWG) conductors as defined by SAE J1128 and 0.75 mm2 and 0.50 mm2 conductors as de

17、fined by ISO 6722. 4.1.3 The J2839 connector will be 4 or 5 circuits only utilizing IEC 61087-2-101 B, D or P code keying arrangements. SAE INTERNATIONAL J2839 Reaffirmed JUL2015 Page 3 of 8 4.1.4 The J2839 connector shall have the capability of transitioning from the connector body to a 4 or 5 wire

18、 jacketed cable with an overall cable OD up to 12.7 mm. 4.1.5 There must be a provision to terminate an overall cable shield or a drain wire to the connector plug housing. 4.1.6 Due to the large jacketed cable diameters required for heavy duty cable construction, strain relief and coupling nut size

19、will deviate from IEC 61076-2-101. The HDM12 overall connector envelope shall not exceed the size requirements shown in Figures 1, 2, 3 and 4. The HDM12EX overall connector envelope shall not exceed the size requirements shown in Figure 5. FIGURE 1 - HDM12 STRAIGHT MALE ENVELOPE DRAWING FIGURE 2 - H

20、DM12 RIGHT ANGLE MALE ENVELOPE DRAWING SAE INTERNATIONAL J2839 Reaffirmed JUL2015 Page 4 of 8 FIGURE 3 - HDM12 STRAIGHT FEMALE ENVELOPE DRAWING FIGURE 4 - HDM12 RIGHT ANGLE FEMALE ENVELOPE DRAWING SAE INTERNATIONAL J2839 Reaffirmed JUL2015 Page 5 of 8 FIGURE 5 - HDM12EX ENVELOPE DRAWING 4.2 Test Req

21、uirements The test requirements apply to the connector-to-connector interface including the connector to cable interface(s), and if applicable, the connector to housing interface for bulkhead mounted connectors. 4.2.1 Test Connectors 4.2.1.1 Testing shall be performed on the mated connector pair. 4.

22、2.1.2 Cable connectors shall be assembled using 100 ohm 10 ohm impedance 0.8 mm2 and 0.5 mm2 two twisted pair jacketed cable. A braided shield or foil shield with drain wire may be used. The shield shall be terminated to the connector housing per the connector manufacturers assembly procedure. 4.2.1

23、.3 Cables may be constructed from ISO 6722 conductors or SAE J1128 conductors. The test requirements for 0.75 mm2 conductors shall be the same as those for 0.8 mm2. 4.2.1.4 Bulkhead connectors shall be mounted per the manufacturers assembly procedure. Ensure that the inside elements of a device moun

24、ted bulkhead connector are not subjected to the effects of water, salt, chemicals, etc. Environmental performance is applicable only to the mating connector side of a device mounted bulkhead surface. 4.2.2 The HDM12 connector under test shall be mated with a coupling torque of 0.8 to 1.0 Nm. The HDM

25、12EX connector under test shall be mated with a coupling torque of 25 to 35 Nm. 4.2.3 Test Procedure The J2839 connectors shall meet the test requirements of and follow the test sequences of SAE J2030 for a sealed signal connector with exceptions as noted. 4.2.3.1 Examination of Product Per SAE J203

26、0 Paragraph 6.1. SAE INTERNATIONAL J2839 Reaffirmed JUL2015 Page 6 of 8 4.2.3.2 Low Voltage Resistance Per SAE J2030 Paragraph 6.2. The maximum resistance for 0.5 mm2 wire is 15 milliohm. 4.2.3.3 Insulation Resistance Per SAE J2030 Paragraph 6.3. For 0.5 mm2 wire, the test current shall be 5 amps 0.

27、1 amps. 4.2.3.4 Connection Resistance Per SAE J2030 Paragraph 6.4 with a test current of 5 amps 0.1 amps and maximum millivolt drop of 50 millivolts. 4.2.3.4.1 For a cable connector, the measuring point shall be 900 to 1000 mm beyond the point of connection. The cable jacket shall remain for a minim

28、um of 850 mm beyond the point of connection. 4.2.3.4.2 For a device mounted bulkhead connector, the terminals are exposed in the interior of the device. The measuring point shall be 0 to 25 mm from the back surface of the bulkhead connector. 4.2.3.5 Pressure Washing Per SAE J2030 Paragraph 6.5. Alte

29、rnatively, the testing may be performed to ISO 20653 to meet the second element 9K. 4.2.3.6 Maintenance Aging Per SAE J2030 Paragraph 6.6. This test may be omitted for assemblies with terminals that are not serviceable. 4.2.3.7 Temperature Life Per SAE J2030 Paragraph 6.7. 4.2.3.8 Ultraviolet Effect

30、s Per SAE J2030 Paragraph 6.8. 4.2.3.9 Mating Forces Per SAE J2030 Paragraph 6.9. Omit this test - M12 connectors are mechanical assist by virtue of the threaded coupling. 4.2.3.10 Unmating Forces Per SAE J2030 Paragraph 6.10. Omit this test - M12 connectors are mechanical assist by virtue of the th

31、readed coupling. 4.2.3.11 Durability Per SAE J2030 Paragraph 6.11. Testing shall be performed for 100 cycles total. 4.2.3.12 Salt Fog Per SAE J2030 Paragraph 6.12 except that the total time shall be 240 hours. 4.2.3.13 Thermal Shock Per SAE J2030 Paragraph 6.13. SAE INTERNATIONAL J2839 Reaffirmed JU

32、L2015 Page 7 of 8 4.2.3.14 Fluid Immersion Per SAE J2030 Paragraph 6.14. 4.2.3.15 Vibration Per SAE J2030 Paragraph 6.15. 4.2.3.16 Shock Per SAE J2030 Paragraph 6.16. 4.2.3.17 Drop Test Per SAE J2030 Paragraph 6.17. The test only applies to cable connector assemblies. 4.2.3.18 Terminal Retention in

33、Connector Per SAE J2030 Paragraph 6.18. This test may be omitted in assemblies where the connector to cable interface is overmolded. The minimum pull out force of 110 N also applies to 20AWG/0.5 mm2 wires. 4.2.3.19 Water Immersion Per SAE J2030 Paragraph 6.19. 4.2.3.20 Connector Retention Per SAE J2

34、030 Paragraph 6.20. This tests the mated connector interface, the connector to multiconductor cable interface and the bulkhead interface of bulkhead mounted connectors. Use a force of 444N in the axis of the connection. Repeat this test with the cable pull 90 degrees off the axis of the connector. T

35、he pull force requirement of HDM12EX connector is 1332 N. 4.2.3.21 Mismating Per SAE J2030 Paragraph 6.21 as noted as follows: 4.2.3.21.1 During this test, the connector shall be rotated 360 degrees while the axial force of 40 to 44 N is applied. 4.2.3.21.2 When the key engages during this rotation,

36、 a torque of 1.4 to 1.5 Nm shall be applied. During the rotation, the threads are in contact but not started/engaged. 4.2.3.22 Current Test Per SAE J2030 Paragraph 6.22 does not apply. 4.2.3.23 Dust Test Per SAE J2030 Paragraph 6.23. Alternatively, the testing may be performed to ISO 20653 to meet t

37、he first element 6K. 4.2.3.24 Temperature/Humidity Per SAE J2030 Paragraph 6.24. 4.2.3.25 Current Cycling Test Per SAE J2030 Paragraph 6.25 does not apply. SAE INTERNATIONAL J2839 Reaffirmed JUL2015 Page 8 of 8 4.2.3.26 Terminal Crimp Strength Per SAE J2030 Paragraph 6.26. This test may be omitted i

38、n assemblies where the connector to cable interface is overmolded. For 0.5 mm2 wire, the minimum tensile strength is 90 N. 4.2.3.27 Final Visual Examination Per SAE J2030 Paragraph 6.27. Base metal exposure is considered a failure. 5. NOTES 5.1 Marginal Indicia A change bar ( l ) located in the left

39、 margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY THE HEAVY DUTY HIGH SPEED DATALINK CONNECTOR TASK FORCE FOR THE TRUCK AND BUS ELECTRICAL SYSTEMS COMMITTEE REAFFIRMED BY THE SAE TRUCK AND BUS ELECTRICAL SYSTEMS COMMITTEE