SAE AS 85028 2A-2010 CONNECTOR ELECTRIC RECTANGULAR INDIVIDUAL CONTACT SEALING POLARIZED CENTER HARDWARE RECEPTACLE CRIMP REMOVABLE SOCKET CONTACTS CLASS E《E级压盖可拆式插座触头的极化中心硬件单触头密封矩.pdf

《SAE AS 85028 2A-2010 CONNECTOR ELECTRIC RECTANGULAR INDIVIDUAL CONTACT SEALING POLARIZED CENTER HARDWARE RECEPTACLE CRIMP REMOVABLE SOCKET CONTACTS CLASS E《E级压盖可拆式插座触头的极化中心硬件单触头密封矩.pdf》由会员分享，可在线阅读，更多相关《SAE AS 85028 2A-2010 CONNECTOR ELECTRIC RECTANGULAR INDIVIDUAL CONTACT SEALING POLARIZED CENTER HARDWARE RECEPTACLE CRIMP REMOVABLE SOCKET CONTACTS CLASS E《E级压盖可拆式插座触头的极化中心硬件单触头密封矩.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD CONNECTOR, ELECTRIC, RECTANGULAR, INDIVIDUAL CONTACT SEALING, POLARIZED CENTER HARDWARE, RECEPTACLE, CRIMP REMOVABLE SOCKET CONTACTS, CLASS EAS85028/2Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system o

2、r transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.

3、org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2004-06REVISED 2010-11THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.AFEDERAL SUPPLY CLASS 5935 AS85028/2SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: AS85028SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance the

4、state of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at whic

5、h time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85028/2ARATIONALE LIMITED SCOPE REVISION REQUIRED TO INCORPORATE AS85028/2-A1. NOT

6、ICE THE REQUIREMENTS FOR PROCURING THE CONNECTORS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF AS85028. FIGURE 1 AS85028/2 CONFIGURATION Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted witho

7、ut license from IHS-,-,-AEROSPACE STANDARD AS85028/2SHEET 2 OF 2REV. ACONNECTOR, ELECTRIC, RECTANGULAR, INDIVIDUAL CONTACT SEALING, POLARIZED CENTER HARDWARE, RECEPTACLE, CRIMP REMOVABLE SOCKET CONTACTS, CLASS ETABLE 1 AS85028/2 DIMENSIONS AND CONSTRUCTION DASHNO. NO. OF CONTACTS ABSCBMAXC.007 DMAXE

8、MAXFMAXWEIGHT (GRAMS) MAX(WITH CONTACTS AND SEALS) INSERTARRANGEMENTMIL-STD-1674 1 52 .550 .990 1.090 1.155 1.900 2.275 85 10.1 2 80 .812 1.250 1.350 1.700 2.045 2.420 100 20.1 3 104 .812 1.250 1.350 2.156 2.500 2.875 120 30.1 4 158 1.250 1.760 1.860 2.156 2.500 2.875 141 40.1 5 212 1.850 2.290 2.39

9、0 2.156 2.500 2.875 180 50.1 NOTES: 1. DIMENSIONS ARE IN INCHES. 2. SOCKET CONTACTS USED WITH THIS CONNECTOR SHALL CONFORM TO AS39029/69. 3. SEALING PLUGS USED WITH THIS CONNECTOR SHALL CONFORM TO AS85028/4. 4. INTERFACIAL SEALS USED WITH THIS CONNECTOR SHALL CONFORM TO AS85028/3. 5. WIRE SEALS USED

10、 WITH THIS CONNECTOR SHALL CONFORM TO AS85028/5. 6. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITL

11、E INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-