NAVY MIL-STD-1323-376-1991 UNIT LOAD FOR UNDERWAY REPLENISHMENT MORTAR 81MM M819 OR M85381 IN PA157 CONTAINER《PA157容器M819和M85381型81MM迫击炮航行的负载》.pdf

《NAVY MIL-STD-1323-376-1991 UNIT LOAD FOR UNDERWAY REPLENISHMENT MORTAR 81MM M819 OR M85381 IN PA157 CONTAINER《PA157容器M819和M85381型81MM迫击炮航行的负载》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-STD-1323-376-1991 UNIT LOAD FOR UNDERWAY REPLENISHMENT MORTAR 81MM M819 OR M85381 IN PA157 CONTAINER《PA157容器M819和M85381型81MM迫击炮航行的负载》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、*- w MIL-STD-1323 -37b 81 9999911 0311908 89T W MIL-STD-1323-376 MILITARY STANDARD (NAWI 2 DECEMBER 1991 UNIT LOAD FOR U N DE R WAY REP L ENI SHM E NT MORTAR, 81MM, M819,OR M85381 IN PA157 CONTAINER UNIT LOAD DATA NUMBER OF CARTRIDGES/CONTAINER 3 NUMBER OF CONTAINERS/UNIT LOAD . 27 GROSS WEIGHT OF O

2、NE CONTAINER . 61 LBS WEIGHT OF WOOD FRAMES (APPROX) . 18 LBS WEIGHT OF STEEL STRAPPING (APPRO X) 5 LBS GROSS WEIGHT OF UNIT LOAD . 1,764 LES A CUBE 45.36 CU FT DO NOT USE FOR SHIPPING WEIGHT FOR HAZARD CLASSIFICATION SEE NAVSEA OP 2165. W NOT STACK MORE THAN 6 UNIT LOADS HIGH IN STORAGE. AMSC NO. -

3、 N/A DISTRIBUTION STATEMENT A APPROVED FOR PUBLIC RELEASE: DISTRIBUTION IS UNLIMITED. NOTES: I. UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. 2. FOR CROSS REFERENCE TO ASSOCIATED TRUCKLOADING, I I I I I CONTAINERLOADING AND CARLOADING MILITARY REV LTR I APPROVAL I DATt I TDA ISYSCOMl STANDAR

4、DS, REFER TO INDEX TO STANDARDS, REV ISION DESCRIPTION M IL - HDBK - 236 IN AVY I. THIS UNIT LOAD IS AUTHORIZED AND RELEASED FOR SHIPPING, HANDLING, STORAGE AND TRANSFER-AT-SEA. IT MAY ALSO BE USED FOR DOMESTIC SHIPMENT IN COMPLIANCE WITH DOT REGULATIONS. REQUIREMENTS FOR CONSTRUCTION OF THIS UNIT L

5、OAD SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF MIL-STD-1323 (NAWI. Ii .T c/ dATr/ O RI GI NATO R WPNSTA EARLE. NEW JERSEY Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-I323 -376 83 9999933 03II909 72b DEPALLETIZING PROCEDURE MI

6、L- STD- 13 23 - 3 76 (NAVY 1 12 8 EDGEPROTECTOR FSNB13C00-2910962 8 7 SEAL STEEL 314 SIZE PALLETIZING PROCEDURE: (A) (E) (C) (E) CUT AND REMOVE LATERAL STRAPS, ITEM 3. CUT AND REMOVE UPPER PERIMETER STRAP, ITEM 4. CUT AND REMOVE LOWER PERIMETER STRAP, ITEM 4. CUT AND REMOVE LONGITUDINAL STRAPS, ITEM

7、 2. REMOVE CONTAINERS AND GATE ASSEMBLIES. (0) THREAD CENTER LONGTTUDINAL STRAP, ITEM 2, BETWEEN 11TH AND 12TH WIRES OF PALLET DECK AS SHOWN IN DETAIL A. THREAD OUTER LONGITUDINAL STRAPS, ITEM 2, BETWEEN 4TH AND 5TH WIRES. POSITION CENTER ROW OF NINE CONTAINERS ON THE PALLET WITH EQUAL OVERHANG ON B

8、OTH ENDS. POSITION ONE GATE ASSEMBLY (SEE DETAIL E) ON EACH SIDE OF CENTER ROW. POSITION THE REMAINING TWO ROWS (18 CONTAINERS) ON THE PALLET WITH EQUAL OVERHANG ON BOTH SIDES AND ENDS. BRING LONGITUDINAL STRAPS, ITEM 2, OVER THE TOP OF THE UNIT LOAD, PLACING SIX (6) EDGE PROTECTORS, ITEM 8, UNDER S

9、TRAPS AS SHOWN. TENSION LONGITUDINAL STRAPC, ITEM 2, AND DOUBLE NOTCH THE SEALS, ITEM 7. THE CENTER STRAP SHOULD BE TENSIONED FIRST. POSITION LOWER PERIMETER STRAP, ITEM 4, AROUND UNIT LOAD AS SHOWN. TENSION AND DOUBLE NOTCH THE SEAL, ITEM 7. FEED UPPER PERIMETER STRAP, ITEM 4, AROUND THE UNIT LOAD

10、AND THROUGH THE HANDLES (SEE DETAIL C) OF THE FOUR CONTAINERS ON THE CORNERS OF THE PALLET. TENSION AND DOUBLE NOTCH THE SEALS, ITEM 7. FEED LATERAL STRAPS, ITEM 3, UNDER THE PALLET AND OVER THE UNIT LOAD AS SHOWN. DO NOT FEED IATERAL STRAPS, ITEM 3, UNDER PERIMETER STRAPS, ITEM 4. POSITION EDGE PRO

11、TECTORS UNDER THE LATERAL STRAPS, ITEM 3, AS SHOWN. TENSION AND DOUBLE NOTCH THE SEALS. 4 6 SPACER BAR, VERTICAL WOOD 2X4X14 SPACER EAR, HORIZONTAL WOOD 2X4X48 - 5 2 4 WPING, PERIMETER STEEL 3/4 x ,035 x 18 Fr 3 3 STRAPPING, LATERAL STEEL 314 X .O35 X 13 FT CENTRALLY LOCATE ON COMAINERS AS SHOWN 6PL

12、 3 REF DETAIL A 2 STRAPPING, LONGITUDINAL STEEL 314 X .O35 X 15 Fi NOTES 1 1. UNLESS OTHERWISE SPECIFIED, ALL MATERIALS SHALL BE IN ACCORDANCE WITH MIL-STD-1323 (NAVY). 2. DO NOT USE TYPE I STRAPPING WITH POWER MACHINES. 1 I PALLET MK 3 MOD O 564200 I 4OX48X4314 REQ. ITEM DESCRIPTION MATL/DWG DIMENS

13、IONS PAGE 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1323 -376 81 H 9999311 03LL9LO 448 = MIL-STD-1323-376 (NAVY) THREAD STRAPPING BENVEEN 4TH AND 5TH WIRES (2PL) AND BETWEENllTHAND12MWIRES. DETAIL 0 DETAIL 0 SPACER ASSY 2 REQD. STRAP TO RUN THROUGH HANDLE AT EACH CORNER AS SHOWN (4PL). DETAIL PREPARING ACTIVITY: NAVY - OS (PROJECT NO. 814-N999) PAGE : REVIEW ACTIVTTY: NAVY - AS, OS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-