DLA SMD-5962-98643 REV C-2012 MICROCIRCUIT LINEAR VOLTAGE REGULATOR 5 VOLT POSITIVE FIXED MONOLITHIC SILICON.pdf

《DLA SMD-5962-98643 REV C-2012 MICROCIRCUIT LINEAR VOLTAGE REGULATOR 5 VOLT POSITIVE FIXED MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-98643 REV C-2012 MICROCIRCUIT LINEAR VOLTAGE REGULATOR 5 VOLT POSITIVE FIXED MONOLITHIC SILICON.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to reflect currents requirements. 05-01-20 Raymond Monnin B Figure 2, correct terminal symbols for case outlines N, T, U, and Z. Add note to table II, Group C end-point test parameters. -gz 09-07-06 Charles F. Saffle C Updated draw

2、ing paragraphs. -sld 12-05-15 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKE

3、D BY Michael C. Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 5 VOLT, POSITIVE, FIXED, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 99-07-14 AMSC N/A REVISION LEVEL C SIZE A C

4、AGE CODE 67268 5962-98643 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E170-12Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98643 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FO

5、RM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation h

6、ardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 98643 01 H T A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.

7、3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit

8、function as follows: Device type Generic number 1/ Circuit function 01 SDP7805A Positive voltage regulator, 5 volt, fixed 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PR

9、F-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H

10、 Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited tem

11、perature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that cl

12、ass. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturer

13、s internal, QML certified flow. This product may have a limited temperature range. 1/ The SDP7805A is similar to the 7805A listed on Standard Microcircuit Drawing 5962-87782. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWI

14、NG SIZE A 5962-98643 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style N See figure 1 3 Z-tab with n

15、onisolated tab, (TO-257Z), with glass seal T See figure 1 3 Flange mount with nonisolated tab, (TO-257), with glass seal U See figure 1 3 Flange mount with isolated tab, (TO-257), with glass seal Z See figure 1 3 Z-tab with isolated tab, (TO-257Z), with glass seal 1.2.5 Lead finish. The lead finish

16、shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage: Operating or output shorted to ground . 35 V dc Transient 43 V dc 2/ Output current (IO) . 1.0 A Storage temperature range -65 C to +150 C Lead temperature (soldering, 10 seconds) +300 C Junction temperature (TJ)

17、 . +150 C 3/ Power dissipation (PD): TC= +25 C . 15 W TA= +25 C . 3.0 W Thermal resistance junction-to-case (qJC): Cases N and T . 3.5 C/W Cases U and Z . 4.2 C/W Thermal resistance junction-to-ambient (qJA) 42 C/W 1.4 Recommended operating conditions. Input voltage range +8 V dc to +25 V dc Ambient

18、 operating temperature range (TA) -55 C to +125 C 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ The 43 volt input rating refers to the ability of the regulator to wit

19、hstand high line or transient condition without damage. Since the regulators maximum current capability is reduced, the output may fall out of regulation at high input voltages under nominal loading. 3/ The device is protected by a thermal shutdown circuit which is designed to turn off the output tr

20、ansistor whenever the device junction temperature is in excess of +150C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98643 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FOR

21、M 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitatio

22、n or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBO

23、OKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 1911

24、1-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. RE

25、QUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Manageme

26、nt (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM p

27、lan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in ac

28、cordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over

29、the full specified operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98643 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3.4 Electri

30、cal test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN liste

31、d in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality c

32、onformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made av

33、ailable to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall

34、affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and

35、 inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in acc

36、ordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and

37、Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-

38、883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

39、,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98643 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55 C TA +125 C unless otherwise specified Group A subgroups Device type Limit

40、s Unit Min Max Output voltage VOUTTA= +25 C 1 01 4.92 5.08 V VIN= 7.5 V to 20 V 2/ 1, 2, 3 4.85 5.15 Line regulation 3/ 4/ VRLINEVIN= 7.5 V to 20 V 1 01 5 mV 2, 3 12 VIN= 8.0 V to 12 V 1 01 4 mV 2, 3 10 Load regulation 3/ VRLOADVIN= 10 V, IO= 5.0 mA to 1.5 A 1 01 12 mV 2, 3 25 VIN= 10 V, IO= 250 mA

41、to 750 mA 1 01 6 mV 2, 3 15 Standby current drain ISCD1 01 5 mA 2, 3 12 Standby current drain change with line D ISCD(line) VIN= 7.5 V to 20 V 1, 2, 3 01 50 mA Standby current drain change with load D ISCD(load) IO= 5.0 mA to 1.0 A 1, 2, 3 01 0.5 mA Dropout voltage VDOVOUT= 100 mV, IO= 1.0 A 1, 2, 3

42、 01 2.5 V Peak output current IO(pk)TA= +25 C 1 01 1.5 3.3 A Short circuit current 5/ IOSVIN= 35 V 1 01 1.2 A 2, 3 2.8 Ripple rejection OUTINVVDDf = 120 Hz, VIN= 8 V to 18 V 4 01 68 dB 5, 6 6/ 60 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted with

43、out license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98643 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55 C TA +125 C unless otherwise specified Grou

44、p A subgroups Device type Limits Unit Min Max Output noise voltage 6/ NOf = 10 Hz to 100 kHz, TA= +25 C 7 01 40 V/V rms Long term stability 6/ DVINt = 1000 hours, TA= +25 C 7 01 75 mV Temperature coefficient 6/ DVOUTVIN= 10 V, IO= 5 mA 1, 3 01 -2 mV/ C 1, 2 -1.5 1/ Unless otherwise specified, VIN= 1

45、0 V and IO= 500 mA. 2/ IO= 5 mA to 1.0 A, P 15 W. 3/ All measurements except output noise voltage and ripple rejection are made at constant junction temperature and with low duty cycle. 4/ Minimum load current for full line regulation is 5.0 mA. 5/ Short circuit protection is only assured up to VIN=

46、 35 V. 6/ If not tested, shall be guaranteed to the limits specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98643 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8

47、DSCC FORM 2234 APR 97 Case outlines T and U. Inches mm 0.005 0.13 0.010 0.25 0.020 0.51 Symbol Millimeters Inches Min Max Min Max A 4.83 5.08 .190 .200 A1 0.89 1.14 .035 .045 A2 3.05 BSC .120 BSC b 0.64 1.02 .025 .040 D 16.38 16.89 .645 .665 D1 10.41 10.92 .410 .430 D3 0.00 0.97 .000 .038 e 2.54 BSC

48、 .100 BSC E 10.41 10.67 .410 .420 L 12.70 19.05 .500 .750 O 13.39 13.64 .527 .537 P 3.56 3.81 .140 .150 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, this item was originally designed using inch-pound units of measurement. In the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STA