DIN EN ISO 11203-2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from.pdf

《DIN EN ISO 11203-2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 11203-2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、January 2010DEUTSCHE NORM English price group 11No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 17.140.20!$Tp“1564977w

2、ww.din.deDDIN EN ISO 11203Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station andat other specified positions from the sound power level(ISO 11203:1995)English version of DIN EN ISO 11203:2010-01Akustik Geruschabstrahlung von Maschinen

3、 und Gerten Bestimmung von Emissions-Schalldruckpegeln am Arbeitsplatz und an anderenfestgelegten Orten aus dem Schallleistungspegel (ISO 11203:1995)Englische Fassung DIN EN ISO 11203:2010-01SupersedesDIN EN ISO 11203:1996-07www.beuth.deDocument comprises pages17DIN EN ISO 11203:2010-01 National for

4、eword This standard has been prepared by Technical Committee ISO/TC 43 “Acoustics”, Subcommittee SC 1 “Noise” (Secretariat: DS, Denmark), Working Group WG 28 “Basic machinery noise emission standards” in collaboration with Technical Committee CEN/TC 211 “Acoustics” (Secretariat: DS, Denmark). The re

5、sponsible German body involved in its preparation was the Normenausschuss Akustik, Lrmminderung und Schwingungstechnik im DIN und VDI (Acoustics, Noise Control and Vibration Engineering Standards Committee in DIN and VDI), Working Committee NA 001-01-04 AA Gerusch-emission von Maschinen und Anlagen;

6、 Messung, Minderung, Datensammlung. Amendment of the European Machinery Directive has made it necessary to review Annexes ZA and ZB in terms of the essential requirements of EU Directive 98/37/EC and the revised Directive, 2006/42/EC. The technical substance of the standard has not been changed. The

7、 DIN Standards corresponding to the International Standards referred to in this document are shown below. The IEC numbers are listed in the currently valid five-digit versions, although they are cited in the text by their last three digits only (i.e. without “60”). ISO 1996-1 DIN 45645-1 ISO 7779 DI

8、N EN ISO 7779 ISO 2204 DIN EN ISO 12001 ISO 9614-1 DIN EN ISO 9614-1 ISO 3740 DIN EN ISO 3740 ISO 9614-2 DIN EN ISO 9614-2 ISO 3741 DIN EN ISO 3741 ISO 11200 DIN EN ISO 11200 ISO 3742 DIN EN ISO 3741 ISO 11201 DIN EN ISO 11201 ISO 3743-1 DIN EN ISO 3743-1 ISO 11202 DIN EN ISO 11202 ISO 3743-2 DIN EN

9、 ISO 3743-2 ISO 11204 DIN EN ISO 11204 ISO 3744 DIN EN ISO 3744 ISO 12001 DIN EN ISO 12001 ISO 3745 DIN EN ISO 3745 IEC 60651 DIN EN 61672 (all parts) ISO 3746 DIN EN ISO 3746 IEC 60804 DIN EN 61672 (all parts) ISO 3747 DIN EN ISO 3747 IEC 60942 DIN EN 60942 ISO 4871 DIN EN ISO 4871 IEC 61260 DIN EN

10、 61260 The national standards are given in Annex NA “Bibliography”. Amendments This standard differs from DIN EN ISO 11203:1996-07 as follows: a) Annexes ZA and ZB have been supplemented to show the relationship between this standard and the Machinery Directive 98/37/EC and the new revised Machinery

11、 Directive 2006/42/EC. Previous editions DIN 45635: 1970-03 DIN 45635-1: 1972-01, 1984-04 DIN EN ISO 11203: 1996-07 2 DIN EN ISO 11203:2010-01 National Annex NA (informative) Bibliography DIN 45645-1, Determination of rating levels from measurement data Part 1: Noise immission in the neighbourhood D

12、IN EN 60942, Electroacoustics Sound calibrators DIN EN 61260, Electroacoustics Octave-band and fractional-octave-band filters DIN EN 61672-1, Electroacoustics Sound level meters Part 1: Specifications DIN EN 61672-2, Electroacoustics Sound level meters Part 2: Pattern evaluation tests DIN EN 61672-3

13、, Electroacoustics Sound level meters Part 3: Periodic tests DIN EN ISO 3740, Acoustics Determination of sound power levels of noise sources Guidelines for the use of basic standards DIN EN ISO 3741, Acoustics Determination of sound power levels of noise sources using sound pressure Precision method

14、s for reverberation rooms DIN EN ISO 3743-1, Acoustics Determination of sound power levels of noise sources Engineering methods for small, movable sources in reverberant fields Part 1: Comparison method for hard-walled test rooms DIN EN ISO 3743-2, Acoustics Determination of sound power levels of no

15、ise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms DIN EN ISO 3744, Acoustics Determination of sound power levels of noise sources using sound pressure Engineering method in an essential free fiel

16、d over a reflecting plane DIN EN ISO 3745, Acoustics Determination of sound power levels of noise sources using sound pressure Precision methods for anechoic and hemi-anechoic rooms DIN EN ISO 3746, Acoustics Determination of sound power levels of noise sources using sound pressure Survey method usi

17、ng an enveloping measurement surface over a reflecting plane DIN EN ISO 3747, Acoustics Determination of sound power levels of noise sources using sound pressure Comparison method for use in situ DIN EN ISO 4871, Acoustics Declaration and verification of noise emission values of machinery and equipm

18、ent DIN EN ISO 7779, Acoustics Measurement of airborne noise emitted by information technology and telecommunications equipment DIN EN ISO 9614-1, Acoustics Determination of sound power levels of noise sources using sound intensity Part 1: Measurement at discrete points 3 DIN EN ISO 11203:2010-01 4

19、DIN EN ISO 9614-2, Acoustics Determination of sound power levels of noise sources using sound intensity Part 2: Measurement by scanning DIN EN ISO 11200, Acoustics Noise emitted by machinery and equipment Guidelines for the use of basic standards for the determination of emission sound pressure leve

20、ls at a work station and at other specified positions DIN EN ISO 11201, Acoustics Noise emitted by machinery and equipment Measurement of emission sound pressure levels at a work station and at other specified positions Engineering method in an essentially free field over a reflecting plane DIN EN I

21、SO 11202, Acoustics Noise emitted by machinery and equipment Measurement of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections DIN EN ISO 11203, Acoustics Noise emitted by machinery and equipment Determination of emission

22、sound pressure levels at a work station and at other specified positions from the sound power level DIN EN ISO 11204, Acoustics Noise emitted by machinery and equipment Measurement of emission sound pressure levels at a work station and at other specified positions Method requiring environmental cor

23、rections DIN EN ISO 12001, Acoustics Noise emitted by machinery and equipment Rules for the drafting and presentation of a noise test code EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11203 August 2009 ICS 17.140.20 Supersedes EN ISO 11203:1995English Version Acoustics Noise emitted by m

24、achinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995) Acoustique Bruit mis par les machines et quipements Dtermination des niveaux de pression acoustique dmission au poste de travail et en

25、 dautres positions spcifies partir du niveau de puissance acoustique (ISO 11203:1995) Akustik Geruschabstrahlung von Maschinen und Gerten Bestimmung von Emissions-Schalldruckpegeln am Arbeitsplatz und an anderen festgelegten Orten aus dem Schallleistungspegel (ISO 11203:1995) This European Standard

26、was approved by CEN on 27 July 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nat

27、ional standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and

28、notified to the CEN Management Centre has the same status as theofficial versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,

29、Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of ex

30、ploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11203:2009: EEN ISO 11203:2009 (E) 2 Contents Page Foreword 3Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC 12Annex ZB (inf

31、ormative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC 13DIN EN ISO 11203:2010-01 Introduction 4 1 Scope.5 1.1 General 5 1.2 Types of noise and noise sources .5 1.3 Test environment .5 1.4 Specified positions 5 1.5 Specific field of applicatio

32、n of each method.6 2 Normative references.6 3 Definitions.6 4 Measurement uncertainty8 5 Quantities to be determined8 6 Procedures8 6.1 General 8 6.2 Methods.8 7 Information to be resorded .9 7.2 Sound source .9 7.2 Conditions under wich the sound power level has been determined 9 7.3 Location(s) of

33、 specified positions10 7.4 Method used .10 7.5 Noise data .10 8 Information to be reported 10 Annex A (informative) Bibliography11 EN ISO 11203:2009 (E) 3 Foreword The text of ISO 11203:1995 has been prepared by Technical Committee ISO/TC 43 “Acoustics” of the International Organization for Standard

34、ization (ISO) and has been taken over as EN ISO 11203:2009 by Technical Committee CEN/TC 211 “Acoustics” the secretariat of which is held by DS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Feb

35、ruary 2010, and conflicting national standards shall be withdrawn at the latest by February 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such pat

36、ent rights. This document supersedes EN ISO 11203:1995. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directives. For relationship with EU Directives, see informative Annexes

37、ZA and ZB, which are integral parts of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, Franc

38、e, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 11203:1995 has been approved by CEN as a EN ISO 11203:

39、2009 without any modification. DIN EN ISO 11203:2010-01 Introduction 0.1 This International Standard specifies methods for determining the emission sound pressure levels at a work station and at other specified positions in the vicinity of machinery and equipment from the sound power level. In gener

40、al, these sound pressure levels are different from those that would be observed when the machinery or equipment is oper- ating in its normal surroundings where the environment may influence the emission sound pressure level. 0.2 This International Standard is one of a series (IS0 11200 to IS0 11204)

41、 which specifies various methods for determining the noise emissions of a piece of machinery or equipment, or a sub-assembly of such equipment (machine under test). IS0 11200 gives guidance on the choice of the method to be used to determine the emission sound pressure levels of machinery and equipm

42、ent. It also gives details of International Standards giving methods for the de- termination of sound power levels. EN ISO 11203:2009 (E) DIN EN ISO 11203:2010-01 41 Scope 1 .I General This International Standard specifies two methods for determining the emission sound pressure levels of machinery a

43、nd equipment, at a work station and at other specified positions nearby, by calculation from the sound power level. The principal purpose of this determination is to permit comparison of the per- formance of different units of a given family of ma- chinery or equipment, under defined environmental c

44、onditions and standardized mounting and operating conditions. The data obtained may also be used for the declaration and verification of emission sound pressure levels as specified in IS0 4871. Emission sound pressure levels are determined with the same frequency weighting and time weighting, or in

45、the same frequency bands, as those for which sound power levels have been determined. NOTES I The contents of this and related International Standards are summarized in table 1 of IS0 11200:1995. 2 At any given position in relation to a particular machine, and for given mounting and operating condit

46、ions, the emis- sion sound pressure levels determined by the method of this International Standard will in general be lower than the directly measured sound pressure levels for the same ma- chine in the typical workroom where it is used. This is due to reverberation and the contributions of other ma

47、chines. A method of calculating the sound pressure levels in the vicinity of a machine operating alone in a workroom is given in IS0 11690-3. Commonly observed differences are I dB to 5 dB, but in extreme cases the difference may be even greater. 1.2 Types of noise and noise sources This Internation

48、al Standard is, in principle, applicable to moving or stationary machines, for indoor or out- door use, particularly those machines which are mass-produced. The methods given in this Inter- national Standard are not applicable to highly direc- tional sound sources used outdoors. This International S

49、tandard is particularly applicable to machines whose largest dimension is less than or equal to 1 m. It is also applicable to larger machines in certain cases (see 6.2.3). This International Standard is applicable to all types of noise as defined in IS0 2204 and IS0 12001 for which methods for determining the sound power level are available. 1.3 Test environment The test environment to be used is that which is sp