DIN EN 1608-2013 Thermal insulating products for building applications - Determination of tensile strength parallel to faces German version EN 1608 2013《建筑物用隔热产品 与表面平行的抗拉强度的测定 德文版本.pdf

《DIN EN 1608-2013 Thermal insulating products for building applications - Determination of tensile strength parallel to faces German version EN 1608 2013《建筑物用隔热产品 与表面平行的抗拉强度的测定 德文版本.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1608-2013 Thermal insulating products for building applications - Determination of tensile strength parallel to faces German version EN 1608 2013《建筑物用隔热产品 与表面平行的抗拉强度的测定 德文版本.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、May 2013 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.

2、100.60!%$;P“2012445www.din.deDDIN EN 1608Thermal insulating products for building applications Determination of tensile strength parallel to faces;English version EN 1608:2013,English translation of DIN EN 1608:2013-05Wrmedmmstoffe fr das Bauwesen Bestimmung der Zugfestigkeit in Plattenebene;Englisc

3、he Fassung EN 1608:2013,Englische bersetzung von DIN EN 1608:2013-05Produits isolants thermiques destins aux applications du btiment Dtermination de la rsistance la traction paralllement aux faces;Version anglaise EN 1608:2013,Traduction anglaise de DIN EN 1608:2013-05SupersedesDIN EN 1608:1997-01ww

4、w.beuth.deDocument comprises 11 pagesIn case of doubt, the German-language original shall be considered authoritative.04.13DIN EN 1608:2013-05 2 A comma is used as the decimal marker. National foreword This document (EN 1608:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulatin

5、g materials and products” (Secretariat: DIN, Germany) The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-56-60 AA Wrmedmmstoffe. DIN Standards corresponding to the International Stand

6、ards referred to in this document are as follows: ISO 5725-1 DIN ISO 5725-1 ISO 5725-2 DIN ISO 5725-2 Amendments This standard differs from DIN EN 1608:1997-01 as follows: a) the standard has been editorially revised. Previous editions DIN 18165: 1957-08, 1963-03 DIN 18164: 1963-01, 1966-08 DIN 1816

7、4-1: 1972-12, 1979-06, 1991-12, 1992-08 DIN 18165-1: 1975-01, 1987-03, 1991-07 DIN 18161-1: 1976-12 DIN EN 1608: 1997-01 National Annex NA (informative) Bibliography DIN ISO 5725-1, Accuracy (trueness and precision) of measurement methods and results Part 1: General principles and definitions DIN IS

8、O 5725-2, Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1608 March 2013 ICS 91.100.60 Supersedes EN 1608:1996En

9、glish Version Thermal insulating products for building applications - Determination of tensile strength parallel to faces Produits isolants thermiques destins aux applications du btiment - Dtermination de la rsistance la traction paralllement aux faces Wrmedmmstoffe fr das Bauwesen - Bestimmung der

10、Zugfestigkeit in Plattenebene This European Standard was approved by CEN on 15 December 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-dat

11、e lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

12、under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Form

13、er Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT

14、EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1608:2013: EEN 1608:2013 (E) 2 Contents Page Foreword . 3 1 Scope 5 2

15、 Normative references . 5 3 Terms and definitions 5 4 Principle 5 5 Apparatus . 5 6 Test specimens 6 7 Procedure . 7 8 Calculation and expression of results 8 9 Accuracy of measurement . 8 10 Test report 9 DIN EN 1608:2013-05 EN 1608:2013 (E) 3 Foreword This document (EN 1608:2013) has been prepared

16、 by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflict

17、ing national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This docume

18、nt supersedes EN 1608:1996. The revision of this standard contains no major changes, only minor corrections and clarifications of an editorial nature. This European Standard is one of a series of standards which specify test methods for determining dimensions and properties of thermal insulating mat

19、erials and products. It supports a series of product standards for thermal insulating materials and products which derive from the Council Directive of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products (Dir

20、ective 89/106/EEC) through the consideration of the essential requirements. This European Standard has been drafted for applications in building, but it may also be used in other areas where it is relevant. This European test standard is one of the following group of interrelated standards on test m

21、ethods for determining dimensions and properties of thermal insulation materials and products, all of which fall within the scope of CEN/TC 88: EN 822, Thermal insulating products for building applications Determination of length and width EN 823, Thermal insulating products for building application

22、s Determination of thickness EN 824, Thermal insulating products for building applications Determination of squareness EN 825, Thermal insulating products for building applications Determination of flatness EN 826, Thermal insulating products for building applications Determination of compression be

23、haviour EN 1602, Thermal insulating products for building applications Determination of the apparent density EN 1603, Thermal insulating products for building applications Determination of dimensional stability under constant normal laboratory conditions (23 C/50 % relative humidity) EN 1604, Therma

24、l insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions EN 1605, Thermal insulating products for building applications Determination of deformation under specified compressive load and temperature conditions EN 1606,

25、Thermal insulating products for building applications Determination of compressive creep DIN EN 1608:2013-05 EN 1608:2013 (E) 4 EN 1607, Thermal insulating products for building applications Determination of tensile strength perpendicular to faces EN 1608, Thermal insulating products for building ap

26、plications Determination of tensile strength parallel to faces EN 1609, Thermal insulating products for building applications Determination of short-term water absorption by partial immersion EN 12085, Thermal insulating products for building applications Determination of linear dimensions of test s

27、pecimens EN 12086, Thermal insulating products for building applications Determination of water vapour transmission properties EN 12087, Thermal insulating products for building applications Determination of long-term water absorption by immersion EN 12088, Thermal insulating products for building a

28、pplications Determination of long-term water absorption by diffusion EN 12089, Thermal insulating products for building applications Determination of bending behaviour EN 12090, Thermal insulating products for building applications Determination of shear behaviour EN 12091, Thermal insulating produc

29、ts for building applications Determination of freeze-thaw resistance EN 12429, Thermal insulating products for building applications Conditioning to moisture equilibrium under specified temperature and humidity conditions EN 12430, Thermal insulating products for building applications Determination

30、of behaviour under point load EN 12431, Thermal insulating products for building applications Determination of thickness for floating floor insulating products EN 13793, Thermal insulating products for building applications Determination of behaviour under cyclic loading EN 13820, Thermal insulating

31、 materials for building applications Determination of organic content According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark

32、, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 1608:2013-

33、05 EN 1608:2013 (E) 5 1 Scope This European Standard specifies the equipment and procedures for determining the tensile strength of a product parallel to its faces. It is applicable to thermal insulating products. This European Standard can be used to determine whether the product has sufficient str

34、ength to withstand stresses during transportation and application. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references,

35、 the latest edition of the referenced document (including any amendments) applies. EN 823, Thermal insulating products for building applications Determination of thickness EN 12085, Thermal insulating products for building applications Determination of linear dimensions of test specimens ISO 5725-1,

36、 Accuracy (trueness and precision) of measurement methods and results Part 1: General principles and definitions ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement

37、method 3 Terms and definitions For the purposes of this document, the following term and definition applies. 3.1 tensile strength parallel to faces t maximum recorded tensile force parallel to the product faces during the pulling operation, divided by the cross-sectional testing area of the test spe

38、cimen 4 Principle A test specimen is attached to two clamps which are fastened in a tensile testing machine and pulled apart at a given speed. The maximum tensile force is recorded and the tensile strength of the test specimen is calculated. 5 Apparatus 5.1 Tensile testing machine, appropriate for t

39、he range of force and displacement involved, capable of having a constant crosshead speed adjusted to (10 1) mm/min and capable of measuring the force to an accuracy of 1 %. 5.2 Two clamps, designed so as to avoid failure of the test specimen in the area of the clamps. The clamps shall be positioned

40、 so that the tensile stress is uniformly distributed during the test. DIN EN 1608:2013-05 EN 1608:2013 (E) 6 An example of suitable equipment is shown in Figure 1. Any test equipment or method which provides the same result with at least the same accuracy may be used. 6 Test specimens 6.1 Dimensions

41、 of test specimens The thickness of the test specimens shall be the original product thickness including any skins, facings, and/or coatings. The test specimens shall be cut with the shape and with the dimensions shown in Figure 2. For small products or because of equipment limitations, the test spe

42、cimen length and width shall be adjusted proportionally, but with a minimum length of 500 mm. Other specimen shapes which provide the same result to at least the same accuracy may be used. 6.2 Number of test specimens The number of test specimens shall be as specified in the relevant product standar

43、d. If the number is not specified, then at least three test specimens shall be used. In the absence of a product standard or any other European Technical Specification, the number of test specimens may be agreed between parties. Figure 1 Example of suitable clamps 6.3 Preparation of test specimens T

44、he test specimens shall be cut from the full size product so that the length direction corresponds to the direction in which the tensile force is applied to the product in its application. DIN EN 1608:2013-05 EN 1608:2013 (E) 7 Test specimens shall be prepared by methods that do not change the origi

45、nal structure of the product. Special methods of preparation, when needed, are given in the relevant product standard or any other European Technical Specification. 6.4 Conditioning of test specimens The test specimens shall be conditioned for at least 6 h at (23 5) C. In case of dispute, they shall

46、 be conditioned at (23 2) C and (50 5) % relative humidity for the time stated in the relevant product standard. 7 Procedure 7.1 Test conditions Testing shall be carried out at (23 5) C. In case of dispute, it shall be carried out at (23 2) C and (50 5) % relative humidity. 7.2 Test procedure Measur

47、e the thickness of the testing area, d, to the nearest millimetre, in accordance with EN 823. Measure the length of the test specimen, l, and the width of the testing area, b, to the nearest millimetre, in accordance with EN 12085. Attach the test specimen centrally between two clamps to distribute

48、the stress uniformly. Place it carefully in the tensile testing machine and increase the tensile force with a constant speed of the crosshead (see 5.1) until failure occurs. Record the maximum tensile force, in kilonewtons. Note the way in which the product failed. Discard any test specimens that fa

49、iled outside the testing area (see Figure 2). DIN EN 1608:2013-05 EN 1608:2013 (E) 8 Key a length of the testing area b width of the testing area Figure 2 Test specimen shape and dimensions 8 Calculation and expression of results Calculate the tensile strength parallel to faces, t, in kilopascals, using the formula: bdF=m (1) where Fmis the maximum tensile force recorded, in kilonewtons; d is the thickness of the te