DIN EN 1487-2014 Building valves - Hydraulic safety groups - Tests and requirements German version EN 1487 2014《建筑物阀门 液压安全类 试验和要求 德文版本EN 1487-2014》.pdf

《DIN EN 1487-2014 Building valves - Hydraulic safety groups - Tests and requirements German version EN 1487 2014《建筑物阀门 液压安全类 试验和要求 德文版本EN 1487-2014》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1487-2014 Building valves - Hydraulic safety groups - Tests and requirements German version EN 1487 2014《建筑物阀门 液压安全类 试验和要求 德文版本EN 1487-2014》.pdf（37页珍藏版）》请在麦多课文档分享上搜索。

1、September 2014 Translation by DIN-Sprachendienst.English price group 15No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).

2、ICS 91.140.60!%:lN“2237343www.din.deDDIN EN 1487Building valves Hydraulic safety groups Tests and requirements;English version EN 1487:2014,English translation of DIN EN 1487:2014-09Gebudearmaturen Hydraulische Sicherheitsgruppen Prfungen und Anforderungen;Englische Fassung EN 1487:2014,Englische be

3、rsetzung von DIN EN 1487:2014-09Robinetterie de btiment Groupes de scurit hydraulique Essais et exigences;Version anglaise EN 1487:2014,Traduction anglaise de DIN EN 1487:2014-09SupersedesDIN EN 1487:2000-06www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.

4、Document comprises 37 pages 08.14 DIN EN 1487:2014-09 2 A comma is used as the decimal marker. National foreword This document (EN 1487:2014) has been prepared by Technical Committee CEN/TC 164 “Water supply” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was t

5、he Normenausschuss Armaturen (DIN Standards Committee Valves), Working Committee NA 003-02-02 AA Armaturen fr die Trinkwasser-installation in Gebuden. Amendments This standard differs from DIN EN 1487:2000-06 as follows: a) the scope has been extended to include nominal sizes DN 15 to DN 20; b) norm

6、ative references have been updated; c) terms and definitions have been modified; d) Subclause 4.1 “General” relating to materials has been reworded; e) Subclauses 4.3 “Detection of residual stress”, 4.4 “Outside visible surfaces”, 4.5 “Corrosion resistance”, 4.6 “Coating adherence” and 4.7 “Compatib

7、ility with the products used for disinfection of the networks” have been added; f) Subclauses 5.2 “Dimensional characteristics”, 5.3 “Test port” and 5.4 “Pressure tapping” have been modified; g) the former Subclause 5.7 “Other threads” has been deleted; h) Subclauses 5.8 “Replacing of the safety val

8、ve” and 5.9 “Check valve” have been added; i) Clause 6 “Apparatus” has been added, thus renumbering of the following clauses was necessary; j) Clause 7 “Hydraulic tests and requirements” has been modified; k) the former Clause 8 “Acoustic tests and requirements” has been editorially revised and is n

9、ow Clause 11; l) Clause 9 “Tests and requirements of the components of the hydraulic safety group” has been modified; m) Clause 10 “Resistance to thermal shocks” has been added; n) Clause 12 “Classification” has been modified; o) Clause 13 “Designation” has been modified; p) Clause 15 “Technical doc

10、uments and presentation at delivery” has been added; q) the former Annex A (informative) has been replaced by informative Annex A “Test sequences”. Previous editions DIN EN 1487: 2000-06 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1487 July 2014 ICS 91.140.60 Supersedes EN 1487:2000English

11、Version Building valves - Hydraulic safety groups - Tests and requirements Robinetterie de btiment - Groupes de scurit hydraulique - Essais et exigences Gebudearmaturen - Hydraulische Sicherheitsgruppen - Prfungen und Anforderungen This European Standard was approved by CEN on 22 May 2014. CEN membe

12、rs are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicatio

13、n to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Manageme

14、nt Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, L

15、ithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17

16、, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1487:2014 EEN 1487:2014 (E) 2 Contents Page Foreword 4 Introduction .6 1 Scope 7 2 Normative references 7 3 Terms and definitions .8 4 Materials and surface fin

17、ishes 11 4.1 General . 11 4.2 Materials 11 4.3 Detection of residual stress . 11 4.3.1 Test . 11 4.3.2 Test method (Procedure) . 11 4.3.3 Requirements 12 4.4 Outside visible surfaces 12 4.4.1 Surfaces without coatings . 12 4.4.2 Surfaces with coatings . 13 4.5 Corrosion resistance 13 4.5.1 Test meth

18、od . 13 4.5.2 Requirements 13 4.6 Coating adherence 13 4.6.1 Test method . 13 4.6.2 Requirements 14 4.7 Compatibility with the products used for disinfection of the networks 14 4.7.1 General . 14 4.7.2 Test method . 14 4.7.3 Requirements 14 5 Design and dimensional requirements 14 5.1 General guidan

19、ce 14 5.2 Dimensional characteristics 15 5.2.1 End connections . 15 5.3 Test port . 17 5.4 Pressure tapping. 17 5.5 Hydraulic safety valve outlet connection to air break to drain 18 5.6 Hydraulic safety valve discharge connection to drain device . 18 5.7 Exclusions . 18 5.8 Replacing of the safety v

20、alve 18 5.9 Check valve . 18 6 Apparatus 18 6.1 General . 18 6.2 Tolerances of parameters and accuracy of measure instruments 18 6.2.1 Tolerances on set parameters . 18 6.2.2 Accuracy of measuring instruments 19 6.2.3 Test media . 19 7 Hydraulic tests and requirements . 19 7.1 Flow rate test . 19 7.

21、1.1 Procedure 19 7.1.2 Requirement 19 7.2 Tightness test 19 DIN EN 1487:2014-09 EN 1487:2014 (E) 3 7.2.1 General . 19 7.2.2 Tightness test for the isolating valve at a pressure of 1,6 MPa (16 bar) . 19 7.2.3 Hydraulic safety group tightness test . 20 8 Mechanical tests and requirements 20 8.1 Mechan

22、ical strength 20 8.1.1 Pressure test of the body of the hydraulic safety group . 20 8.1.2 Bending test of the body and pull out test of the drainage of the hydraulic safety group 20 8.1.3 Torsional strength of the hydraulic safety groups body 22 8.1.4 Tensile strength of the captive rotating nuts .

23、23 8.2 Mechanical strength of the easing gear of the pressure safety valve . 23 8.2.1 Procedure . 23 8.2.2 Requirement . 23 9 Tests and requirements of the components of the hydraulic safety group 24 9.1 Isolating valve 24 9.1.1 General . 24 9.1.2 Test of manual operation 24 9.1.3 Endurance test . 2

24、4 9.1.4 Test for manual operation 24 9.2 Check valve 25 9.2.1 Verification of the leaktightness between the groups body and the check valve at low pressure 25 9.2.2 Verification of the leaktightness between the groups body and the check valve under high pressure . 25 9.3 Pressure safety valve 25 9.3

25、.1 Pressures . 25 9.3.2 Cold water pressure tests. 26 9.3.3 Steam test. 27 9.4 Endurance test . 28 9.4.1 Procedure . 28 9.4.2 Requirement . 28 9.5 Easing gear (manual control device) . 29 9.5.1 Operation of the easing gear 29 9.5.2 Easing gear endurance test 29 9.6 Manual drainage device 29 9.6.1 Ge

26、neral . 29 9.6.2 Flow rate test . 29 9.7 Air break to drain . 29 10 Resistance to thermal shocks 30 10.1 Test method . 30 10.2 Requirement . 30 11 Acoustic tests and requirements . 30 12 Classification . 31 13 Designation 31 14 Marking . 32 15 Technical documents and presentation at delivery . 32 An

27、nex A (informative) Test sequences . 34 DIN EN 1487:2014-09 EN 1487:2014 (E) 4 Foreword This document (EN 1487:2014) has been prepared by Technical Committee CEN/TC 164 “Water Supply”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard,

28、 either by publication of an identical text or by endorsement, at the latest by January 2015, and conflicting national standards shall be withdrawn at the latest by January 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN

29、 and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1487:2000. The main changes compared to EN 1487:2000 are as follows: a) the Scope has been modified to nominal sizes DN 15 to DN 25; b) Normative references were updated; c) Terms

30、 and definitions were changed; d) subclause 4.1 (general wording for materials) was modified; e) subclauses 4.3 (Detection of residual stress), 4.4 (Outside visible surfaces), 4.5 (Corrosion resistance), 4.6 (Coating adherence) and 4.7 (Compatibility with the products used for disinfection of the ne

31、tworks) were added; f) subclauses 5.2 (Dimensional characteristics), 5.3 (Test port) and 5.4 (Pressure tapping) were modified; g) subclause 5.7 (Other threads) was deleted; h) subclauses 5.8 (Replacing of the safety valve) and 5.9 (Check valve) were added; i) Clause 6 (Apparatus) was added, thus ren

32、umbering of the following clauses was necessary; j) Clause 7 (Hydraulic tests and requirements) was modified; k) Clause 8 (Acoustic tests and requirements) was moved to Clause 11 and modified editorially; l) Clause 9 (Tests and requirements of the components of the hydraulic safety group) was modifi

33、ed; m) Clause 10 (Resistance to thermal shocks) was added; n) Clause 12 (Classification) was modified; o) Clause 13 (Designation) was modified editorially; p) Clause 15 (Technical documents, presentation at delivery) was added; q) informative Annex A was replaced by informative Annex A (Test sequenc

34、es). DIN EN 1487:2014-09 EN 1487:2014(E)5 According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Y

35、ugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 1487:2014-09 EN 1487:2014 (E) 6 Introd

36、uction In respect of potential adverse effect on the quality of water intended for human consumption, caused by the product covered by this standard: a) This standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA. b) I

37、t should be noted that, whilst awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and or the characteristics of this product remain in force. DIN EN 1487:2014-09 EN 1487:2014 (E) 7 1 Scope This European Standard specifies dimensions, materials and

38、 performance requirements (including methods of test) for hydraulic safety groups, of nominal sizes from DN 15 to DN 25, having working pressures1)from 0,1 MPa (1 bar) to 0,7 MPa (7 bar). Hydraulic safety groups are intended for fitting to the potable water supply of storage water heaters, having a

39、maximum storage temperature of 95C. Hydraulic safety groups limit the pressure in hot water heaters, prevent the backflow of water into the main circuit and prevent the discharged water to get into contact with the water in the water heater. Hydraulic safety groups do not control the temperature. Th

40、ey ensure the hydraulic safety of water heaters if the mechanical resistance of the water heater remains at least equal to the rating pressure. NOTE The use of the device specified in this European Standard does not override the need to use controls (e.g. thermostats and cut-outs) which act directly

41、 on the power sources of water heaters. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the

42、referenced document (including any amendments) applies. EN 248:2002, Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr EN 806-1, Specifications for installations inside buildings conveying water for human consumption - Part 1: General EN 806-2, Specification for install

43、ations inside buildings conveying water for human consumption - Part 2: Design EN 806-3, Specifications for installations inside buildings conveying water for human consumption - Part 3: Pipe sizing - Simplified method EN 806-4, Specifications for installations inside buildings conveying water for h

44、uman consumption - Part 4: Installation EN 806-5, Specifications for installations inside buildings conveying water for human consumption - Part 5: Operation and maintenance EN 1488, Building valves - Expansion groups - Tests and requirements EN 1567, Building valves - Water pressure reducing valves

45、 and combination water pressure reducing valves - Requirements and tests EN 1717:2000, Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow EN 10226-1, Pipe threads where pressure tight joints are made on the thread

46、s - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation EN 13959, Anti-pollution check valves - DN 6 to DN 250 inclusive family E, type A, B, C and D 1) All pressures are gauge unless otherwise stated. DIN EN 1487:2014-09 EN 1487:2014 (E) 8 EN ISO 22

47、8-1, Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1) EN ISO 3822-1, Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 1: Method of measurement (ISO 3

48、822-1) EN ISO 3822-3, Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 3: Mounting and operating conditions for in-line valves and appliances (ISO 3822-3) EN ISO 4628-3, Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting (ISO 4628-3) EN ISO 6509, Corrosion of metals and alloys - Determination of dezincification resistance of