DIN EN 1015-10-2007 Methods of test for mortar for masonry - Part 10 Determination of dry bulk density of hardened mortar(includes Amendment A1 2006) English version of DIN EN 1015.pdf

《DIN EN 1015-10-2007 Methods of test for mortar for masonry - Part 10 Determination of dry bulk density of hardened mortar(includes Amendment A1 2006) English version of DIN EN 1015.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1015-10-2007 Methods of test for mortar for masonry - Part 10 Determination of dry bulk density of hardened mortar(includes Amendment A1 2006) English version of DIN EN 1015.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、May 2007DEUTSCHE NORM English price group 6No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.100.10!,xb2“9856315www.d

2、in.deDDIN EN 1015-10Methods of test for mortar for masonry Part 10: Determination of dry bulk density of hardened mortar (includesAmendment A1:2006)English version of DIN EN 1015-10:2007-05Prfverfahren fr Mrtel fr Mauerwerk Teil 10: Bestimmung der Trockenrohdichte von Festmrtel (enthlt nderung A1:20

3、06)Englische Fassung DIN EN 1015-10:2007-05SupersedesDIN EN 1015-10:1999-10www.beuth.deDocument comprises 7 pages 08.07DIN EN 1015-10:2007-05 2 National foreword This standard has been prepared by CEN/TC 125 “Masonry” (Secretariat: BSI, United Kingdom). The responsible German body involved in its pr

4、eparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Technical Committees NA 005-06-01 AA Mauerwerksbau and NA 005-06-04 AA Prfverfahren. This European Standard is part of a series of standards specifying methods used to check compliance of mortar for maso

5、nry with the requirements specified in the relevant product standard. Amendment A1:2006 has been integrated in this standard and is marked by a vertical line in the left margin. Amendments This standard differs from DIN EN 1015-10:1999-10 as follows: a) In clause 2, the explanatory text has been ame

6、nded. b) All occurrences of “pr” preceding EN references have been deleted throughout the document. c) In clause 3, the detail “when submerged in water in a saturated condition” has been deleted. d) In clause 4, three symbols have been deleted. e) In clause 7, the heading “7.1 Drying to constant mas

7、s” and the entire subclause 7.2 have been deleted, and the drying temperature has been changed. f) In clause 8, a new first paragraph has been added. Previous editions DIN EN 1015-10: 1999-10 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1015-10 August 1999 +A1 December 2006 ICS 91.100.10 Eng

8、lish version Methods of test for mortar for masonry Part 10: Determination of dry bulk density of hardened mortar Mthodes dessai des mortiers pour maonnerie Partie 10: Dtermination de la masse volumique apparente sche du mortier durci Prfverfahren fr Mrtel fr Mauerwerk Teil 10: Bestimmung der Trocke

9、nrohdichte von Festmrtel EN 1015-10:1999 was approved by CEN on 1999-07-08 and Amendment A1 on 2006-10-26. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterati

10、on. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation

11、under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungar

12、y, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, and the United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNG Management

13、 Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1015-10:1999 + A1:2006 EEN 1015-10:1999 + A1:2006 (E) 2 Contents Page Foreword to EN 1015-10:19993 Foreword to EN 1015-10:1999/A1:200

14、6.3 1 Scope 3 2 Normative references 3 3 Principle4 4 Symbols 4 5 Apparatus .4 6 Sampling, preparation and storage of test samples4 7 Procedure .4 8 Calculation and expression of results.5 9 Test report 5 EN 1015-10:1999 + A1:2006 (E) 3 Foreword to EN 1015-10:1999 This European Standard has been pre

15、pared by Technical Committee CEN/TC 125 “Masonry”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2000, and conflicting national standards shall

16、be withdrawn at the latest by December 2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland

17、, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Foreword to EN 1015-10:1999/A1:2006 This document (EN 1015-10:1999/A1:2006) has been prepared by Technical Committee CEN/TC 125 “Masonry”, the secretariat of which is held by BSI. This Amendment to

18、 the European Standard EN 1015-10:1999 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. According to the CEN/CENELEC Internal R

19、egulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands

20、, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. 1 Scope This European Standard specifies a method for determining the dry bulk density of hardened mortars. It is applicable to lightweight and general purpose and thin layer mortars using specime

21、ns of regular shape. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 99

22、8-1, Specification for mortar for masonry Part 1: Rendering and plastering mortar with inorganic binding agents EN 998-2, Specification for mortar for masonry Part 2: Masonry mortar EN 1015-2, Methods of test for mortar for masonry Part 2: Bulk sampling of mortars and preparation of test mortars EN

23、1015-3, Methods of test for mortar for masonry Part 3: Determination of consistence of fresh mortar (by flow table) EN 1015-10:1999 + A1:2006 (E) 4 EN 1015-11, Methods of test for mortar for masonry Part 11: Determination of flexural and compressive strength of hardened mortar 3 Principle The dry bu

24、lk density of a given specimen of hardened mortar is determined as the quotient of its mass in oven dried condition, and the volume which it occupies. 4 Symbols ms,dryis the oven dry mass of specimen of hardened mortar, in kilograms (kg) Vsis the volume of specimen of hardened mortar, in cubic metre

25、s (m3) 5 Apparatus 5.1 A weighing instrument accurate to 0,1 % of the total mass of the specimen. 5.2 A ventilated oven, capable of maintaining a temperature of 70 C 5 C or 60 C 5 C. 5.3 Moulds as described in EN 1015-11. 6 Sampling, preparation and storage of test samples The fresh mortar for this

26、test shall have a volume of not less than 50 times the maximum aggregate particle size, and in no case less than 50 ml or 1,5 times the quantity needed to perform the test, whichever is the greater. It shall be obtained either by reduction of the bulk test sample (see EN 1015-2) using a sample divid

27、er or by quartering or by preparation from dry constituents and water in the laboratory. The flow value of the mortar in the bulk test sample shall be determined in accordance with EN 1015-3 and reported. Laboratory mixed samples shall, before testing, be brought to a defined flow value as specified

28、 in EN 1015-2. Ready to use mortars (factory-made wet mortars which are retarded), and pre-batched air-lime/sand wet mortars when not gauged with hydraulic binders, shall be tested within their specified workable life. The length of mixing period shall be measured from the moment all constituents ar

29、e introduced into the mixer. Before testing, the batch shall be gently stirred by hand using a trowel or palette knife in 5 s to 10 s to counteract any false setting etc., but without any additional mixing of the batch. Any deviation from the mixing procedure shall be noted. A test sample shall comp

30、rise three specimens prepared in moulds, their shape, preparation and storage being in accordance with EN 1015-11. 7 Procedure Dry the specimen in the oven at a temperature of 105 C 5 C until the constant mass is reached. For samples with organic constituents, e.g. expanded polystyrene aggregate, us

31、e a drying temperature of 60 C 5 C. The specimen is considered to have reached constant mass if two consecutive weighings 2 h apart EN 1015-10:1999 + A1:2006 (E) 5 during the drying, do not differ by more than 0,2 % of the mass of the dry specimen. Record the mass of the specimen, ms,dryin kg to the

32、 nearest 0,1 %. 8 Calculation and expression of results Vsis taken as the volume of the mould, which is 256 106m3. Calculate the dry bulk density of each mortar specimen as the ratio of the recorded mass, ms,dry, to the volume Vs. Calculate the mean value from the individual values of each mortar sp

33、ecimen, all values rounded to the nearest 10 kg/m3. 9 Test report The test report shall include the following information: a) the number, title and date of issue of this European Standard; b) the place, date and time of taking the bulk test sample1); NOTE This is the sample taken from the bulk suppl

34、y that is to be used for all of the tests in EN 1015. c) the method used for taking the bulk test sample (if known) and the name of the organization that took it; d) the type, origin and designation of the mortar by reference to the relevant part of EN 998:1993; e) the date of testing; f) the date a

35、nd time of preparing test samples for test (i.e. date and time of any mixing, casting, moulding, or demoulding procedure, if appropriate); g) flow value of test mortar determined in accordance with EN 1015-3; h) details of test specimens including number, dimensions, mass etc., if appropriate; i) test results (individual and mean values of dry bulk density rounded to the nearest 10 kg/m3); j) remarks, if any. 1) This information is contained on the certificate of sampling (see EN 1015-2).