DIN EN 10149-1-2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 1 General technical delivery conditions German version EN 10149-1 2013《采用冷成型.pdf

《DIN EN 10149-1-2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 1 General technical delivery conditions German version EN 10149-1 2013《采用冷成型.pdf》由会员分享，可在线阅读，更多相关《DIN EN 10149-1-2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 1 General technical delivery conditions German version EN 10149-1 2013《采用冷成型.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、December 2013 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 77.140.50!%*zV“2078751www.din.deDDIN EN 10149-1Hot rolled flat products made of high yield strength steels for coldforming Part 1: General technical delivery conditions;English version EN 10149-1:2013,English translation of DIN EN 10149-1:2013-12Warmgewalzte Flacherzeugnisse aus Sthlen mit hoher

3、Streckgrenze zumKaltumformen Teil 1: Allgemeine technische Lieferbedingungen;Englische Fassung EN 10149-1:2013,Englische bersetzung von DIN EN 10149-1:2013-12Produits plats lamins chaud en aciers haute limite dlasticit pour formage froid Partie 1: Conditions gnrales techniques de livraison;Version a

4、nglaise EN 10149-1:2013,Traduction anglaise de DIN EN 10149-1:2013-12SupersedesDIN EN 10149-1:1995-11www.beuth.deDocument comprises 18 pagesIn case of doubt, the German-language original shall be considered authoritative.11.13DIN EN 10149-1:2013-12 2 A comma is used as the decimal marker. National f

5、oreword This document (EN 10149-1:2013) has been prepared by Technical Committee ECISS/TC 103 “Structural steel other than reinforcements”, (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Eisen und Stahl (Iron and Steel Standards Committee

6、), Working Committee NA 021-00-04-01 UA Sthle fr den Stahlbau. Amendments This standard differs from DIN EN 10149-1:1995-11 as follows: a) normative references have been updated; b) note 1 to definition 3.2 has been revised; c) Clause 6 “Classification and designation” has been updated; d) in Subcla

7、use 7.4.1.1, the note has been modified and changed to standard text; e) in Subclause 7.5.1 “Weldability”, NOTE 2 has been added; f) in Table 1, values for Mn, Ti and Mo have been modified; g) the Bibliography has been updated; h) the standard has been editorially revised. Previous editions DIN EN 1

8、0149-1: 1995-11 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10149-1 September 2013 ICS 77.140.50 Supersedes EN 10149-1:1995English Version Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions Produits plats lamins chaud

9、 en aciers haute limite dlasticit pour formage froid - Partie 1: Conditions gnrales techniques de livraison Warmgewalzte Flacherzeugnisse aus Sthlen mit hoher Streckgrenze zum Kaltumformen - Teil 1: Allgemeine technische Lieferbedingungen This European Standard was approved by CEN on 17 August 2013.

10、 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on

11、application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELE

12、C Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

13、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue

14、 Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10149-1:2013: EEN 10149-1:2013 (E) 2 Contents Page Foreword . 3 1 Scope 4 2 Normative references . 4 3 Terms and definitions 5 4 Information to be sup

15、plied by the purchaser 6 4.1 Mandatory information . 6 4.2 Options . 6 5 Dimensions, mass and tolerances 6 5.1 Dimensions and tolerances . 6 5.2 Mass of steel 6 6 Classification and designation 6 6.1 Classification and grades 6 6.2 Designation 6 7 Technical requirements . 7 7.1 Steel manufacturing p

16、rocess . 7 7.2 Delivery condition 7 7.3 Chemical composition . 8 7.4 Mechanical properties 9 7.5 Technological properties . 9 7.6 Surface finish . 10 7.7 Internal soundness 10 8 Inspection and testing . 11 8.1 General . 11 8.2 Sampling . 11 8.3 Test units 11 8.4 Verification of chemical composition

17、11 8.5 Preparation of samples and test pieces 11 8.6 Test methods 12 8.7 Retests and resubmission for testing . 13 8.8 Inspection documents . 13 9 Marking . 14 10 Disputes 14 11 Options . 14 Bibliography 16 DIN EN 10149-1:2013-12 EN 10149-1:2013 (E) 3 Foreword This document (EN 10149-1:2013) has bee

18、n prepared by Technical Committee ECISS/TC 103 “Structural steel other than reinforcements”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2014, an

19、d conflicting national standards shall be withdrawn at the latest by March 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This

20、document supersedes EN 10149-1:1995. In comparison with EN 10149-1:1995, the following significant technical changes were made: definition 3.2, Note 1 modified; subclause 7.4.1.1, Note modified and changed to standard text; subclause 7.5.1, Note 2 for welding suitability of grades S900MC and S960MC

21、added; Table 1, values for Mn, Ti and Mo modified. The specific requirements for hot rolled products made of high yield strength steels for cold forming are given in the EN 10149-2 and EN 10149-3. The titles of the other Parts of this European Standard are: Part 2: Technical delivery conditions for

22、thermomechanical rolled steels; Part 3: Technical delivery conditions for normalized or normalized rolled steels. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgar

23、ia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turk

24、ey and the United Kingdom. DIN EN 10149-1:2013-12 EN 10149-1:2013 (E) 4 1 Scope 1.1 This European Standard specifies requirements for flat products made of weldable, hot-rolled, high yield strength alloy quality and special steels for cold forming. EN 10149-1 specifies the general delivery condition

25、s. EN 10149-2 specifies the delivery conditions for thermomechanically rolled steels in the grades given in Table 1 (chemical composition) and Table 2 (mechanical properties) of Part 2. EN 10149-3 specifies the delivery conditions for normalised or normalised rolled steels in the grades given in Tab

26、le 1 (chemical composition) and Table 2 (mechanical properties) of Part 3. 1.2 This European Standard does not apply to products for pressure vessels and products for which other European Standards exist or European Standards dealing with steels for general structural applications are being prepared

27、: Hot-rolled products of structural steels (see EN 10025 parts 1 to 6); Hot finished structural hollow sections of non-alloy and fine grain steels (see EN 10210-1). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable

28、for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10020, Definition and classification of grades of steel EN 10021, General technical delivery conditions for steel pr

29、oducts EN 10029, Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape EN 10048, Hot-rolled narrow steel strip Tolerances on dimensions and shape EN 10051, Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels Tolerances on dimensi

30、ons and shape EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:2007, Definition of steel products EN 10149-2:2013, Hot rolled flat products made of high yield strength steels for cold forming Part 2: Technical delivery conditions for thermomechanically rolled steels EN

31、 10149-3:2013, Hot rolled flat products made of high yield strength steels for cold forming Part 3: Technical delivery conditions for normalized or normalized rolled steels EN 10160, Ultrasonic testing of steel flat product of thickness equal to or greater than 6 mm (reflection method) EN 10162, Col

32、d-rolled steel sections Technical delivery conditions Dimensional and cross-sectional tolerances DIN EN 10149-1:2013-12 EN 10149-1:2013 (E) 5 EN 10163-1, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 1: General requirements EN 10163-2, Delivery

33、requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 2: Plate and wide flats EN 10168, Steel products Inspection documents List of information and description EN 10204, Metallic products Types of inspection documents EN ISO 148-1, Metallic materials Charpy pend

34、ulum impact test Part 1: Test method (ISO 148-1) EN ISO 377, Steel and steel products Location and preparation of samples and test pieces for mechanical testing (ISO 377) EN ISO 2566-1, Steel Conversion of elongation values Part 1: Carbon and low alloy steels (ISO 2566-1) EN ISO 6892-1:2009, Metalli

35、c materials Tensile testing Part 1: Method of test at room temperature (ISO 6892-1:2009) EN ISO 7438, Metallic materials Bend test (ISO 7438) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10052:1993, EN 10079:2007 and the following apply. 3.1 fine g

36、rained steels steels with fine grain structure with an equivalent index of ferritic grain size 6 Note 1 to entry: For the determination of grain sizes, see EN ISO 643. 3.2 thermomechanical rolling rolling process in which the final deformation is carried out in a certain temperature range leading to

37、 a material condition with certain properties which cannot be achieved or repeated by heat treatment alone Note 1 to entry: Hot forming or post weld heat treatment at a temperature above 580 C may lower the strength values and for this reason is better not performed. Flame straightening can be appli

38、ed in accordance with CEN/TR 10347. For grades S900MC and S960MC, subsequent heating at temperature above 400 C is not recommended. Note 2 to entry: Thermomechanical rolling can include processes with an increasing cooling rate with or without tempering including self-tempering but excluding direct

39、quenching and quenching and tempering. Note 3 to entry: In some publications, the word TMCP (Thermomechanical Control Process) is also used. 3.3 normalised rolled rolling process in which the final deformation is carried out in a certain temperature range leading to a material condition equivalent t

40、o that obtained after normalising so that the specified values of the mechanical properties are retained even after normalising Note 1 to entry: In international publications for both the normalising rolling, as well as the thermomechanical rolling, the expression “controlled rolling“ may be found.

41、However, in view of the different applicability of the products, a distinction of the terms is necessary. DIN EN 10149-1:2013-12 EN 10149-1:2013 (E) 6 4 Information to be supplied by the purchaser 4.1 Mandatory information The following information shall be supplied by the purchaser at the time of t

42、he order: a) details of the product form and quantity; b) reference to this European Standard; c) nominal dimensions and tolerances (see 5.1); d) the grade and delivery condition of the steel (see EN 10149-2 and EN 10149-3); e) type of inspection document (see 8.8). 4.2 Options A number of options a

43、re specified in Clause 11. In the event that the purchaser does not indicate his wish to implement any of these options, the supplier shall supply in accordance with the basic specification. 5 Dimensions, mass and tolerances 5.1 Dimensions and tolerances Dimensions and tolerances shall be in accorda

44、nce with EN 10029, EN 10048 or EN 10051. 5.2 Mass of steel The calculated mass shall be determined using a volumetric mass of 7,85 kg/dm3. 6 Classification and designation 6.1 Classification and grades Classification shall be in accordance with EN 10149-2 and EN 10149-3 which specify steel grades th

45、at are alloy quality steels or alloy special steels according to EN 10020. The steels for flat products specified in EN 10149-2 and EN 10149-3 are subdivided into grades on the basis of the minimum specified yield strength at ambient temperature. 6.2 Designation 6.2.1 Steel names and steel numbers F

46、or the steel grades covered by this European Standard, the steel names are allocated in accordance with EN 10027-1; the steel numbers are allocated in accordance with EN 10027-2. DIN EN 10149-1:2013-12 EN 10149-1:2013 (E) 7 6.2.2 Details for the designation The designation shall consist of: the numb

47、er of this European Standard (EN 10149-2 or EN 10149-3); the steel number or the steel name consisting of: the symbol S (for structural steel); the indication of the minimum specified yield strength expressed in MPa1); the symbol for the delivery condition (M or N) (see EN 10149-2 and EN 10149-3); t

48、he capital letter C indicating the steel is suitable for cold forming (see EN 10149-2 and EN 10149-3). EXAMPLE 1 Thermomechanically rolled (M) structural steels (S) with a specified minimum yield strength at room temperature of 420 MPa1)(420) suitable for cold forming (C): Steel EN 10149-2 - 1.0980

49、or Steel EN 10149-2 - S420MC EXAMPLE 2 Structural steels (S) with a specified minimum yield strength at room temperature of 420 MPa1) (420) in the normalised or normalised rolled condition (N) suitable for cold forming (C): Steel EN 10149-3 - 1.0981 or Steel EN 10149-3 - S420NC 7 Technical requirements 7.1 Steel manufacturing process 7.1.1 The steel manufacturing process shall be at the manufacturers option. If specified at the time of the order, the steel manufacturing process sh