BS F 153-2006 Properties of oil resistant silicone rubber sheet mouldings and extrusions - Specification《抗油硅橡胶板、模和挤压的特性 规范》.pdf
《BS F 153-2006 Properties of oil resistant silicone rubber sheet mouldings and extrusions - Specification《抗油硅橡胶板、模和挤压的特性 规范》.pdf》由会员分享,可在线阅读,更多相关《BS F 153-2006 Properties of oil resistant silicone rubber sheet mouldings and extrusions - Specification《抗油硅橡胶板、模和挤压的特性 规范》.pdf(14页珍藏版)》请在麦多课文档分享上搜索。
1、BS F 153:2006Properties of oil resistant silicone rubber sheet, moulding and extrusions SpecificationICS 49.025.40NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPublishing and copyright informationThe BSI copyright notice displayed in this document indicates wh
2、en the document was last issued. BSI 2006ISBN 0 580 49384 9The following BSI references relate to the work on this standard:Committee reference ACE/65Draft for comment 05/30130016 DCPublication historyFirst published October 2006Amendments issued since publicationAmd. no. Date Text affectedBS F 153:
3、2006 BSI 2006 iBS F 153:2006ContentsForeword ii1 Scope 12 Normative references 13 Terms and definitions 24 Material 25 Properties 36 Test sheet manufacture 57 Test methods 58 Quality of material 79 Marking, labelling and packaging 7AnnexesAnnex A (normative) Manufacture of test sheet 8Bibliography 9
4、List of tablesTable 1 Tests as moulded material 3Table 2 Tests after exposure to heat ageing 4Table 3 Tests after immersion in fluid Oil No. 1 4Table 4 Tests after immersion in fluid Liquid 101 5Summary of pagesThis document comprises a front cover, an inside front cover, pages i and ii, pages 1 to
5、9 and a back cover.BS F 153:2006ii BSI 2006ForewordPublishing informationThis British Standard was published by BSI and came into effect on 31 October 2006. It was prepared by ACE/65/-/25, Rubbers, elastomers and sealants, under the authority of Technical Committee ACE/65, Inspection and testing req
6、uirements for non-metallic materials. A list of organizations represented on this committee can be obtained on request to its secretary.Information about this documentThis document supersedes DTD 5582A with Amendment No. 1 June 1979 and Amendment No. 2 August 1981, which was declared obsolescent by
7、the Ministry of Defence from 1 April 1999 and DTD 818 Class N, which was declared obsolescent by the Ministry of Defence in 1999.Hazard warningsWARNING. This British Standard calls for the use of substances and/or procedures that can be injurious to health if adequate precautions are not taken. It r
8、efers only to technical suitability and does not absolve the user from legal obligations relating to health and safety at any stage.Use of this documentIt has been assumed in the preparation of this British Standard that the execution of its provisions will be entrusted to appropriately qualified an
9、d experienced people, for whose use it has been produced.Presentational conventionsThe provisions of this standard are presented in roman (i.e. upright) type. Its requirements are expressed in sentences in which the principal auxiliary verb is “shall”.Commentary, explanation and general informative
10、material is presented in smaller italic type, and does not constitute a normative element.Contractual and legal considerationsThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard
11、cannot confer immunity from legal obligations. BSI 2006 1BS F 153:20061 ScopeThis British Standard specifies requirements for an oil resistant silicone rubber material possessing excellent ozone resistance properties intended for the production of items such as sheet, mouldings and certain extrusion
12、s, for use in fluid sealing applications where low compression set is of prime importance. The material is suitable for contact with heavy mineral and certain diester based oils over the temperature range p65 C to 150 C1).For applications in air the material is suitable over the temperature range p6
13、5 C to 250 C.This material standard is to be used in conjunction with BS EN 3207.NOTE 1 Material and products manufactured from this specification, when used in fluid sealing applications, may be used up to 200 C for short intermittent periods.NOTE 2 Material and products manufactures from this spec
14、ification are not intended for use in contact with petroleum based fuels, light mineral oils or greases derived from them.NOTE 3 Further information on the suitability of silicone rubber for design applications can be found in SBAC Technical Specification No. 97 1.NOTE 4 Marking BS F 153:2006 on or
15、in relation to a product represents a manufacturers declaration of conformity, i.e. a claim by or on behalf of the manufacturer that the product meets the requirements of the standard. The accuracy of the claim is solely the claimants responsibility. Such a declaration is not to be confused with thi
16、rd party certification of conformity.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the reference cited applies. For undated references, the latest edition of the referenced document (including any amendment
17、s) applies.BS 903-A1 (ISO 2781), Physical testing of rubber Part A1: Determination of densityBS 903-A6 (ISO 815), Physical testing of rubber Part A6: Method for determination of compression set at ambient, elevated or low temperaturesBS ISO 1817, Rubber, vulcanized Determination of the effect of liq
18、uidsBS ISO 188 (BS 903-A19), Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tests1)Silicone rubber products, when properly stored at room temperature and in the absence of hostile environments, deteriorate very slowly and, for most practical purposes, the storage life may
19、 be considered indefinite. However, the rate of deterioration increases markedly with increase in temperature and the service life of the rubber therefore depends upon the operational temperature. Conversely, the maximum temperature at which the rubber may be used depends upon the useful life requir
20、ed.BS F 153:20062 BSI 2006BS 903-A26 (ISO 48), Physical testing of rubber Part A26: Method for determination of hardness (hardness between 10 IRHD and 100 IRHD)BS 3734-1 (ISO 3302-1), Rubber Tolerances for products Part 1: Dimensional tolerancesBS EN 3207, Rubber compounds Technical specificationBS
21、F 68, Controlled storage of vulcanized rubbers for use in aerospace applicationsBS F 69, Packaging and identification of vulcanized rubber itemsBS ISO 34-1, Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test piecesBS ISO 37, Physical testing o
22、f rubber Part A2: Method for determination of tensile stress Strain propertiesBS ISO 1817, Rubber, vulcanized Determination of the effect of liquids3 Terms and definitionsFor the purposes of this British Standard, the following terms and definitions apply.3.1 polymermaterial formed by joining togeth
23、er many (poly) individual units (mer) of one or more monomers3.2 vulcanizationthermosetting reaction involving the use of heat and pressure, resulting in greatly increased strength and elasticity of rubber-like materials4Material4.1 Material compositionSilicone polymer shall consist of a homogeneous
24、 mix of recognized rubber quality products suitably compounded and cured to meet the requirements of this specification. No reclaimed or ground vulcanized waste shall be used in the mix.4.2 Manufacturing controlSilicone rubber material and products manufactured from this material shall be formulated
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSF1532006PROPERTIESOFOILRESISTANTSILICONERUBBERSHEETMOULDINGSANDEXTRUSIONSSPECIFICATION 硅橡胶 挤压 特性 规范

链接地址:http://www.mydoc123.com/p-582799.html