BS EN 61300-3-48-2013 Fibre optic interconnect devices and passive components Basic test and measurement procedures Examinations and measurements Spring compression force of the coe.pdf

《BS EN 61300-3-48-2013 Fibre optic interconnect devices and passive components Basic test and measurement procedures Examinations and measurements Spring compression force of the coe.pdf》由会员分享，可在线阅读，更多相关《BS EN 61300-3-48-2013 Fibre optic interconnect devices and passive components Basic test and measurement procedures Examinations and measurements Spring compression force of the coe.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationFibre optic interconnect devices and passive components Basic test and measurement proceduresPart 3-48: Examinations and measurements Spring compression force of the coupling sleeve for rectangular ferrule multi-fibre connectorsBS EN 61300-3-48:2013Copyright European Committ

2、ee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National forewordThis British Standard is the UK implementation of EN 61300-3-48:2013. It isidentical to IEC 61300-3-48:2013.The UK par

3、ticipation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre opticinterconnecting devices and passive components.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purpo

4、rt to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013ISBN 978 0 580 75981 9ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations

5、.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2013.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61300-3-48:2013Copyright European Committee for Electrotechnical Standardization Provided

6、by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD EN 61300-3-48 NORME EUROPENNE EUROPISCHE NORM September 2013 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotec

7、hnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61300-3-48:2013 E ICS 33.180.20 English version Fibre

8、optic interconnect devices and passive components - Basic test and measurement procedures - Part 3-48: Examinations and measurements - Spring compression force of the coupling sleeve for rectangular ferrule multi-fibre connectors (IEC 61300-3-48:2013) Dispositifs dinterconnexion et composants passif

9、s fibres optiques - Procdures fondamentales dessais et de mesures - Partie 3-48: Examens et mesures - Force de compression du ressort du manchon de couplage des connecteurs multifibres munis de frules rectangulaires (CEI 61300-3-48:2013) Lichtwellenleiter - Verbindungselemente und passive Bauteile -

10、 Grundlegende Prf- und Messverfahren - Teil 3-48: Messungen - Federdruckkraft der Kupplungshlse fr rechteckige Mehrfasersteckverbinder - Ferrulen (IEC 61300-3-48:2013) This European Standard was approved by CENELEC on 2013-08-19. CENELEC members are bound to comply with the CEN/CENELEC Internal Regu

11、lations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC

12、member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official ver

13、sions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, t

14、he Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61300-3-48:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networki

15、ng permitted without license from IHS-,-,-EN 61300-3-48:2013 - 2 - Foreword The text of document 86B/3522/CDV, future edition 1 of IEC 61300-3-48, prepared by SC 86B, “Fibre optic interconnecting devices and passive components“, of IEC TC 86, “Fibre optics“ was submitted to the IEC-CENELEC parallel

16、vote and approved by CENELEC as EN 61300-3-48:2013. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-05-19 latest date by which the national standards conflicting wit

17、h the document have to be withdrawn (dow) 2016-08-19 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of th

18、e International Standard IEC 61300-3-48:2013 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61300-3-1 NOTE Harmonised as EN 61300-3-1. IEC 61754-7 NOTE Harmonise

19、d as EN 61754-7. IEC 61754-10 NOTE Harmonised as EN 61754-10. IEC 61754-18 NOTE Harmonised as EN 61754-18. BS EN 61300-3-48:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without li

20、cense from IHS-,-,- 2 61300-3-48 IEC:2013(E) CONTENTS 1 Scope . 5 2 Normative references . 5 3 General description 5 4 Apparatus . 5 4.1 General . 5 4.2 Fixture . 5 4.3 Force transfer cup . 5 4.4 Force gauge 5 4.5 Sliding stage . 6 4.6 Observation instrument . 6 5 Procedure. 7 6 Details to be specif

21、ied 7 Annex A (informative) Example of positions for MPO connector (IEC 61754-7) 8 Bibliography 9 Figure 1 Measurement of coupling sleeve compression force . 6 Figure 2 Details of force transfer 7 Figure A.1 Position of coupling sleeve before measurement 8 Figure A.2 Position of coupling sleeve duri

22、ng measurement . 8 BS EN 61300-3-48:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-61300-3-48 IEC:2013(E) 5 FIBRE OPTIC INTERCONNECT DEVICES AND PASSIVE

23、 COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 3-48: Examinations and measurements Spring compression force of the coupling sleeve for rectangular ferrule multi-fibre connectors 1 Scope The purpose of this part of IEC 61300 is to describe the procedure required to measure the spring compress

24、ion force of the coupling sleeve for rectangular ferrule multi-fibre connectors. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undat

25、ed references, the latest edition of the referenced document (including any amendments) applies. None. 3 General description The measurement of the coupling sleeve compression force is made with the optical connector fixed. Then the coupling sleeve is moved to the stipulated position to measure the

26、coupling sleeve compression force with a force gauge. 4 Apparatus 4.1 General The apparatus consists of the following elements. See Figures 1 and 2. 4.2 Fixture The fixture shall be able to hold the optical connector without influencing the measurement of the spring compression force of the coupling

27、 sleeve. The fixture shall be able to hold the optical connector with a force larger than the stipulated coupling sleeve compression force. If measurement is repeated, the location of the optical connector shall not be changed. 4.3 Force transfer cup The force transfer cup shall push only the coupli

28、ng sleeve without contacting any other elements of the optical connector. 4.4 Force gauge The force gauge shall be able to measure at least from 2,9 N to 6,9 N (compression force range). The force gauge is placed so that its pushing direction is the same as the coupling sleeve steering direction. BS

29、 EN 61300-3-48:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 6 61300-3-48 IEC:2013(E) 4.5 Sliding stage The sliding stage shall not impede the locatio

30、n of the force gauge (4.4) and should be placed so that it can move in the same direction as the coupling sleeve. 4.6 Observation instrument The observation instrument shall have sufficient magnification to verify that the coupling sleeve is located at the stipulated location within a 0,1 mm margin.

31、 Coupling sleeve Force transfer cup Force gauge Sliding stage Fixture IEC 1604/13 Figure 1a Top view Observation instrument Sliding stage Force gauge Coupling sleeve Force transfer cup Fixture IEC 1605/13 Figure 1b Side view Figure 1 Measurement of coupling sleeve compression force BS EN 61300-3-48:

32、2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-61300-3-48 IEC:2013(E) 7 Force transfer cup Coupling sleeve IEC 1607/13 IEC 1606/13 Figure 2a Top view Fi

33、gure 2b Perspective view Figure 2 Details of force transfer 5 Procedure The procedure is as follows: a) Set the optical connector under test into the fixture. b) Have the pushing part contact the edge of the coupling sleeve under test and confirm that it is located such that only the coupling sleeve

34、 is pushed, checking that the force transfer cup does not interfere with the optical connector. c) Set the observation instrument to confirm that the coupling sleeve is properly compressed to the intended position. d) Use the force gauge to set the force transfer cup and coupling sleeve at the measu

35、rement position. Confirm the location of the coupling sleeve with the observation instrument. When the edge of the coupling sleeve is within a 0,1 mm range from the measurement position, read the value of the force gauge. 6 Details to be specified The following details, as applicable, shall be state

36、d in the relevant specification: maximum allowed compression force for the force gauge; pre-conditioning procedure; recovery procedure; acceptance/failure criteria; number of times the test is performed on each component; any deviation from measuring procedure; measurement uncertainty. BS EN 61300-3

37、-48:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 8 61300-3-48 IEC:2013(E) Annex A (informative) Example of positions for MPO connector (IEC 61754-7)

38、Coupling sleeve endface Z(Mechanical reference plane) IEC 1608/13 Figure A.1a Side view ZCoupling sleeve endface IEC 1609/13 Figure A.1b Top view Figure A.1 Position of coupling sleeve before measurement ZIEC 1610/13 Figure A.2a Side view Coupling sleeve endface (in the range of 0 m to 0,1 mm to the

39、 rig or to the left of datum Z) ZIEC 1611/13 Figure A.2b Top view Figure A.2 Position of coupling sleeve during measurement BS EN 61300-3-48:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking per

40、mitted without license from IHS-,-,-61300-3-48 IEC:2013(E) 9 Bibliography IEC 61300-3-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination IEC 61754-7, Fibre optic interconnecting devices and pa

41、ssive components Fibre optic connector interfaces Part 7: Type MPO connector family IEC 61754-10, Fibre optic interconnecting devices and passive components Fibre optic connector interfaces Part 10: Type Mini-MPO connector family IEC 61754-18, Fibre optic interconnecting devices and passive componen

42、ts Fibre optic connector interfaces Part 18: Type MT-RJ connector family _ BS EN 61300-3-48:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page del

43、iberately left blankCopyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BSI is the national body responsible for preparing British Standards and other standards-

44、related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together b

45、usiness, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organization

46、s of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or

47、 Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Devel

48、opment Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted Europe