ASTM E2979-2018 Standard Classification for Discarded Materials from Manufacturing Facilities and Associated Support Facilities《制造设施和相关辅助设施废弃材料的标准分类》.pdf

《ASTM E2979-2018 Standard Classification for Discarded Materials from Manufacturing Facilities and Associated Support Facilities《制造设施和相关辅助设施废弃材料的标准分类》.pdf》由会员分享，可在线阅读，更多相关《ASTM E2979-2018 Standard Classification for Discarded Materials from Manufacturing Facilities and Associated Support Facilities《制造设施和相关辅助设施废弃材料的标准分类》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E2979 18Standard Classification forDiscarded Materials from Manufacturing Facilities andAssociated Support Facilities1This standard is issued under the fixed designation E2979; the number immediately following the designation indicates the year oforiginal adoption or, in the case of rev

2、ision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This standard classifies discarded materials from manu-facturing facilities and associated on-site

3、support facilities.1.2 This classification system is based on classification,location, disposition, and treatment.1.3 This classification does not purport to address or super-sede proper waste disposal required by laws and regulations.1.4 This standard does not purport to address all of thesafety co

4、ncerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance wit

5、h internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 Federal Standa

6、rd:240 CFR Part 261 Identification and Listing of HazardousWaste3. Terminology3.1 Definitions:3.1.1 aerobic digestion, nprocess in which micro-organisms break down organic materials(s) in the presence ofoxygen.3.1.2 anaerobic digestion, nprocess in which micro-organisms break down organic material(s

7、) in the absence ofoxygen.3.1.3 hazardous material, nmaterial that, because of itsquantity, concentration, or characteristics, is capable of: (1)causing, or significantly contributing to, an increase in mortal-ity or to an increase in serious irreversible, or incapacitating,illness or injury, or (2)

8、 posing a present or potential hazard tohuman health or to the environment when improperly treated,stored, transported, or disposed of, or otherwise managed.3.1.3.1 DiscussionThe U.S. Environmental ProtectionAgency (US EPA) has developed a list of materials that areconsidered hazardous material and

9、has developed criteria andtest methods to determine if the material has hazardouscharacteristics. These listings and testing criteria can be foundin 40 CFR 261.3.1.4 landfill, ndisposal site for the deposit of materialsonto or into land under controlled or regulated conditions.3.1.5 non-process disc

10、arded material, nmaterial gener-ated and disposed of at a manufacturing facility that isunrelated to a manufacturing process.3.1.5.1 DiscussionExamples include, non-process materi-als from office activities, construction or demolition projects,or ground maintenance.3.1.6 process discarded material,

11、nmaterial generated anddisposed of at a manufacturing facility that is related to amanufacturing process.3.1.6.1 DiscussionDisposal of nonconforming processmaterials that cannot be reworked or raw material packagingare examples of process discarded material.3.1.7 regulated material, ndiscarded mater

12、ial that is offi-cially classified by relevant local, national, or internationalagencies or jurisdictions having statutory authority to establishwaste classification.3.1.8 re-use, nmaterials that have not reached their usefulend of life and are transferred to an entity that can use thematerial or pr

13、oduct again in its current state.3.1.8.1 DiscussionComputers or laboratory equipmentdonated to school and off-spec finished goods donated to atechnical school are examples of re-use.3.1.9 special material, nclass of materials having uniqueregulatory disposal requirements because of potential human o

14、renvironmental impacts that shall be managed to minimize therisk of harm to the environment or human health, or both.1This classification is under the jurisdiction of ASTM Committee E60 onSustainability and is the direct responsibility of Subcommittee E60.13 on Sustain-able Manufacturing.Current edi

15、tion approved Jan. 1, 2018. Published February 2018. DOI: 10.1520/E2979-18.2Available from U.S. Government Publishing Office (GPO), 732 N. Capitol St.,NW, Washington, DC 20401, http:/www.govinfo.gov.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. U

16、nited StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barri

17、ers to Trade (TBT) Committee.13.1.9.1 DiscussionFluorescent light bulbs, lithiumbatteries, asbestos, radioactive materials, halon, and pesticidesare examples of special material.4. Significance and Use4.1 This classification can be used to classify materialoutputs from manufacturing facilities and a

18、ssociated supportfacilities. This classification does not include classification ofemissions to air or water.4.2 This classification can be used to classify discardedmaterials for marketing claims associated with discardedmaterials generation and development of consistent trackingmetrics for manufac

19、turing facilities.5. Basis of Classification5.1 Materials shall be classified according to the steps in thissection. See Fig. 1 and Table 1 for further guidance onclassification.5.2 Step 1: Type of MaterialDiscarded materials shall beclassified into one of the following:5.2.1 Non-Process Discarded M

20、aterial5.2.2 Process Discarded Material5.3 Step 2: ClassificationDiscarded materials shall befurther classified according to classification status.5.3.1 Regulated Material5.3.1.1 SpecialFIG. 1 Manufacturing Facility Discarded Material Classification FlowchartE2979 1825.3.1.2 Hazardous or5.3.2 Unregu

21、lated5.4 Step 3: LocationMaterials shall be further classifiedaccording to the location of disposition.5.4.1 On-site or5.4.2 Off-site5.5 Step 4: DispositionMaterials shall be further classifiedinto one of the following final arrangement types:5.5.1 Re-use5.5.2 Recycle or5.5.3 Treatment5.6 Step 5: Tr

22、eatmentTreatment for materials include thefollowing types of material treatment facilities:5.6.1 Landfill5.6.2 Incineration5.6.3 Anaerobic digestion5.6.4 Aerobic digestion and5.6.5 Other6. Classification6.1 All discarded materials shall be classified per Section 5using abbreviations detailed in Tabl

23、e 1.6.1.1 For example, process discarded material sent from onemanufacturing facility to another for recycling would beclassified as PUFR Process discarded material (P), Unregu-lated (U), Sent off-site (F), for Recycling (R).6.2 Additional classification may be included and shall betracked separatel

24、y.6.2.1 For example, discarded materials may be furtherclassified based on the presence of feedstock energy content forthe purpose of life-cycle inventories.7. Keywords7.1 discarded materials; waste; waste treatmentASTM International takes no position respecting the validity of any patent rights ass

25、erted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time b

26、y the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will rece

27、ive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Inte

28、rnational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or throu

29、gh the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Discarded Materials Classification System1. Discarded Materials 2. Classification 3. Location 4. Disposition 5. TreatmentProcess Discarded Material (P) Regulated (R) On-site (O) Re-use (U) Landfill (1)Non-Process Discarded Material (D) Special (1) Off-site (F) Recycle (R) Incineration (2)Hazardous (2) Treatment (T) Anaerobic digestion (3)Unregulated (U) Aerobic digestion (4)Other (5)E2979 183