IEC 60317-23-2013 Specifications for particular types of winding wires - Part 23 Solderable polyesterimide enamelled round copper wire class 180《特种绕组线规格.第23部分 180级丝包可软焊聚酰亚胺漆包圆铜线》.pdf

《IEC 60317-23-2013 Specifications for particular types of winding wires - Part 23 Solderable polyesterimide enamelled round copper wire class 180《特种绕组线规格.第23部分 180级丝包可软焊聚酰亚胺漆包圆铜线》.pdf》由会员分享，可在线阅读，更多相关《IEC 60317-23-2013 Specifications for particular types of winding wires - Part 23 Solderable polyesterimide enamelled round copper wire class 180《特种绕组线规格.第23部分 180级丝包可软焊聚酰亚胺漆包圆铜线》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60317-23 Edition 3.0 2013-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires Part 23: Solderable polyesterimide enamelled round copper wire, class 180 Spcifications pour types particuliers de fils de bobinage Partie 23: Fil brasable de section ci

2、rculaire en cuivre maill avec polyesterimide, classe 180 IEC60317-23:2013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic

3、 or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contac

4、t the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compri

5、s la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit n

6、ational de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and pub

7、lishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published

8、. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.i

9、ec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30

10、 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistanc

11、e, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A pr

12、opos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous

13、permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications

14、de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglai

15、s et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez

16、-nous: csciec.ch. IEC 60317-23 Edition 3.0 2013-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires Part 23: Solderable polyesterimide enamelled round copper wire, class 180 Spcifications pour types particuliers de fils de bobinage Partie 23: Fil brasa

17、ble de section circulaire en cuivre maill avec polyesterimide, classe 180 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE K ICS 29.060.10 PRICE CODE CODE PRIX ISBN 978-2-8322-1140-3 Registered trademark of the International Electrotechnical Commission Marque dpos

18、e de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60317-23 IEC:2013 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope

19、 . 6 2 Normative references . 6 3 Terms, definitions, general notes and appearance 6 3.1 Terms and definitions 6 3.2 General notes 6 3.2.1 Methods of test 6 3.2.2 Winding wire 6 3.3 Appearance . 7 4 Dimensions 7 5 Electrical resistance . 7 6 Elongation 7 7 Springiness 7 8 Flexibility and adherence 7

20、 9 Heat shock . 7 10 Cut-through 7 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 1,600 mm) . 7 12 Resistance to solvents 8 13 Breakdown voltage . 8 14 Continuity of insulation . 8 15 Temperature index . 8 16 Resistance to refrigerants . 8 17 Solderability .

21、 9 17.1 Nominal conductor diameters up to and including 0,100 mm 9 17.2 Nominal conductor diameters over 0,100 mm 9 18 Heat or solvent bonding 9 19 Dielectric dissipation factor . 9 20 Resistance to transformer oil 9 21 Loss of mass 9 23 Pin hole test . 9 30 Packaging 9 Bibliography 10 Table 1 Resis

22、tance to abrasion 8 60317-23 IEC:2013 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 23: Solderable polyesterimide enamelled round copper wire, class 180 FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organizati

23、on for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC p

24、ublishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with m

25、ay participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agree

26、ment between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC P

27、ublications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used

28、or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corr

29、esponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for

30、 any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees an

31、d IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) A

32、ttention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights

33、. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60317-23 has been prepared by IEC technical committee 55: Winding wires. This third edition cancels and replaces the second edition published in 1990, Amendment 1:1997 and Amendment 2:1999.

34、This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: new 3.2.2 containing general notes on winding wire, formerly a part of the scope; revision to references to IEC 60317-0-1:2013 to clarify that their

35、application is normative; consolidation of 17.1 and 17.2 of the solderability requirements; modification to Clause 19, Dielectric dissipation factor; new Clause 23, Pin hole test. 4 60317-23 IEC:2013 The text of this standard is based on the following documents: FDIS Report on voting 55/1413/FDIS 55

36、/1434/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 60317 series, published under the general

37、title Specifications for particular types of winding wires, can be found on the IEC website. The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. The committee has decided

38、 that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended.

39、60317-23 IEC:2013 5 INTRODUCTION This part of IEC 60317 is one of a series of standards which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851); 2) Specifications for particular types of winding wir

40、es (IEC 60317); 3) Packaging of winding wires (IEC 60264). 6 60317-23 IEC:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 23: Solderable polyesterimide enamelled round copper wire, class 180 1 Scope This part of IEC 60317 specifies the requirements of solderable enamelled round copper

41、 winding wire of class 180 with a sole coating based on polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or mo

42、re additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is: Grade 1: 0,020 mm up to and including 1,600 mm; Grade 2: 0,020 mm up to and including 1,600 mm. The nominal conductor diameters are specified in Clause 4

43、of IEC 60317-0-1:2013. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docume

44、nt (including any amendments) applies. IEC 60317-0-1:2013, Specifications for particular types of winding wires Part 0-1: General requirements Enamelled round copper wire 3 Terms, definitions, general notes and appearance 3.1 Terms and definitions Subclause 3.1 of IEC 60317-0-1:2013 applies. 3.2 Gen

45、eral notes 3.2.1 Methods of test Subclause 3.2.1 of IEC 60317-0-1:2013 applies. In case of inconsistencies between IEC 60317-0-1:2013 and this part of IEC 60317, the latter shall prevail. 3.2.2 Winding wire Class 180 is a thermal class that requires a minimum temperature index of 180 and a heat shoc

46、k temperature of at least 200 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. 60317-23 IEC:2013 7 3.3 Appearance S

47、ubclause 3.3 of IEC 60317-0-1:2008 applies. 4 Dimensions Clause 4 of IEC 60317-0-1:2008 applies. 5 Electrical resistance Clause 5 of IEC 60317-0-1:2008 applies. 6 Elongation Clause 6 of IEC 60317-0-1:2008 applies. 7 Springiness Clause 7 of IEC 60317-0-1:2008 applies. 8 Flexibility and adherence Clau

48、se 8 of IEC 60317-0-1:2008 applies. For 8.4, the constant K used for the calculation of the number of revolutions for the peel test shall be 110 mm. 9 Heat shock Clause 9 of IEC 60317-0-1:2008 applies. The minimum heat shock temperature shall be 200 C. 10 Cut-through No failure shall occur within 2

49、min at 265 C. 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 1,600 mm) The wire shall meet the requirements given in Table 1. For intermediate nominal conductor diameters, the value of the next larger nominal conductor diameter shall be taken. 8 60317-23 IEC:2013 Table 1 Resistance to abrasion Nominal conductor diameter mm Grade 1 Grade 2 Minimum average force to failure N