IEC TR 60943 AMD 1-2008 Guidance concerning the permissible temperature rise for parts of electrical equipment in particular for terminals Amendment 1《电气设备部件(特别.pdf

《IEC TR 60943 AMD 1-2008 Guidance concerning the permissible temperature rise for parts of electrical equipment in particular for terminals Amendment 1《电气设备部件(特别.pdf》由会员分享，可在线阅读，更多相关《IEC TR 60943 AMD 1-2008 Guidance concerning the permissible temperature rise for parts of electrical equipment in particular for terminals Amendment 1《电气设备部件(特别.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC/TR 60943Edition 2.0 2008-12TECHNICAL REPORT RAPPORT TECHNIQUEGuidance concerning the permissible temperature rise for parts of electrical equipment, in particular for terminals Guide concernant lchauffement admissible des parties des matriels lectriques, en particulier les bornes de raccordemen

2、t IEC/TR60943:1998/A1:2008 AMENDMENT 1 AMENDEMENT 1 Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzer

3、land All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country

4、of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, au

5、cune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le

6、 copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.chWeb: www.iec.chAbou

7、t the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review

8、 by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also

9、 gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia

10、.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch

11、/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.chTel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est

12、la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possde

13、z ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne

14、aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par em

15、ail. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechni

16、que International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.chTl.: +41 22 919 02 11 Fax: +41 22 919 0

17、3 00 Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IEC/TR 60943Edition 2.0 2008-12TECHNICAL REPORT RAPPORT TECHNIQUEGuidance concerning the permissible temperature rise for

18、parts of electrical equipment, in particular for terminals Guide concernant lchauffement admissible des parties des matriels lectriques, en particulier les bornes de raccordement INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE EICS 29.020 PRICE CODECODE PRIXISBN

19、2-8318-1018-7AMENDMENT 1 AMENDEMENT 1 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or network

20、ing permitted without license from IHS-,-,- 2 TR 60943 Amend. 1 IEC:2008 FOREWORD This amendment has been prepared by IEC technical committee 32: Fuses. The text of this amendment is based on the following documents: DTR Report on voting 32/187/DTR 32/188/RVC Full information on the voting for the a

21、pproval of this amendment can be found in the report on voting indicated in the above table. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the

22、specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition; or amended. _ Page 63 Replace the existing Table 6 with the following new table: Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for Resale

23、No reproduction or networking permitted without license from IHS-,-,-TR 60943 Amend. 1 IEC:2008 3 Table 6 Typical values of temperature rise and temperature limits* Description of component Column A Maximum temperature rise Ku(an= 20 C) Column B Maximum temperature C (an= 40 C) Remarks Spring contac

24、ts Copper and copper alloys uncoated in OG t in NOGt in oil Tinned in OG, NOGt, oilb e35p75q4050 Nature of contact a, c, eSilver- b, s or nickel-plated b in OGtor NOGt in oil For contactors, in oil 75q50 105 Deterioration of the oil Bolted connections Copper, aluminium, and their alloys, uncoated in

25、 OGt in NOGt60q 75qTinnedbin OG or NOGt,105 Creep point of tin Silver- b, s or nickel-plated b in OG or NOGt in oil 75q100 Deterioration of the oil For contactors, in oil 105 Deterioration of the oil Terminals d, f,rTo be connected to exterior conductors by screws or bolts Uncoated Tinned b Silver-

26、or nickel-plated b60q75q105 Creep point of tin Other contact materials g, hMetallic parts In contact with Insulation class i: Y A E B F H enamel: oil base synthetic acting as springs at position of a tin soldering 90 105 120 130 155 180 100 120 j100 kAgeing of insulation Permanent deterioration Brea

27、king Oil for oil-immersed switchgearl, mAll parts which are metallic or of insulating material in contact with oil, except for contacts m90 100 Deterioration of the oil Electric motors and resistance nManual control components metallic non-metallic 55 65 IEC 60364-4-42 :1980 SurfacesoExpected to be

28、touched in normal operation but not to be held continuously in the hand metallic non metallic 70 80 Accessible, but not designed to be touched in normal operation metallic non metallic 80 90 * For notes, see following page. Copyright International Electrotechnical Commission Provided by IHS under li

29、cense with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 4 TR 60943 Amend. 1 IEC:2008 NOTES a For connection units in vacuum, the limit values of temperature and temperature rise do not apply to the components in the vacuum. The other components must not exce

30、ed the temperature and temperature rise values given in Table 6. Maximum acceptable temperature rises in NOGt are the same for silver-plated or nickel-plated copper as for bare copper, because of the absence of oxygen. b The following are considered as silver contacts: solid silver contacts, contact

31、s with inlaid silver strips, silver-plated contacts. In general, for all plated metals, the quality of the plating must be such that a protective layer remains in the contact zone: 1) after the making and breaking tests (if any); 2) after the permissible short period current test; 3) after mechanica

32、l test, in accordance with the correct specification for each material. If not, the contact must be considered as “bare”. For nickel-plated contacts, the contact resistance and contact life will be equivalent to those of silver if the temperature rise is kept within the prescribed limits. This can b

33、e achieved by higher contact forces, for example. c When engaging parts have different coatings, or one part is of bare metal, the permissible temperatures and temperature rises shall be: 1) for spring-contacts, those of the surface material having the lowest value permitted in Table 6; 2) for bolte

34、d connections, those of the surface material having the highest value permitted in Table 6. d Values of the tightening torque for screws are given in the appropriate product standard, for example Table IV of IEC 60947-1:1988. e For fuses, the temperature rise to be considered can be increased to tak

35、e into account the proportion of heat from the fuse element transmitted by conduction to the contacts. Refer to the appropriate specifications for these components. f The temperature and temperature rise values are valid even if the conductor connected to the terminals is not protected by a covering

36、. g When materials other than those shown in Table 6 are used, their properties shall be taken into consideration. h Limited by the necessity of not damaging surrounding parts. i The classification of insulation is given in IEC 60085:1984. j Temperature shall not reach such a value that the elastici

37、ty of the material is reduced. k This applies when soldering is the main method of joining the two parts; otherwise, this limit may be increased to 110 C. l The measurement must be made in the upper part of the oil. m It is recommended that particular attention be paid to questions of vaporisation a

38、nd oxidation when using oil with a low flash-point. n Regulations in force. o For manual control components located inside enclosures which are accessible upon opening the enclosure, and which are not used frequently, higher temperatures may be allowed. The distinction between metallic and non-metal

39、lic surfaces depends on the thermal conductivity of the surface. Coats of paint and varnish are not considered to modify the thermal conductivity of the surface. On the other hand, certain plastic coatings can noticeably reduce the thermal conductivity of a metallic surface and allow it to be consid

40、ered as non-metallic. This rule does not apply to materials which comply with standards which state that the temperature or temperature-rise limits for accessible surfaces are fixed. p This limit can be increased to: 45 K for low voltage supply equipment downstream from meter boxes or rising mains;

41、for contactors operating on continuous service. Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TR 60943 Amend. 1 IEC:2008 5 65 K for contactors operating on 8 h, intermittent

42、 or temporary service, where conditions of use are those permitted in the appropriate product standards. q Limited by the necessity of causing no damage to adjacent parts and in particular to the insulation in contact. r For terminals intended for connection to insulated conductors, see 5.3.2. s For

43、 some low-voltage industrial equipment, the temperature rise is limited only by the need not to damage surrounding parts. t NOG = Not oxidizing gas; OG = Oxidizing gas. u Higher values can be admitted, respecting in any case Note q, if: products standards admit higher values, or manufacturers can pr

44、ove a correct long term ageing behaviour of the contacts. In this case, agreement on the acceptable values should be reached between the user and the manufacturer. _ Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking

45、permitted without license from IHS-,-,- 6 TR 60943 Amend. 1 CEI:2008 AVANT-PROPOS Le prsent amendement a t tabli par le comit dtudes 32 de la CEI: Coupe-circuit fusibles. Le texte de cet amendement est issu des documents suivants: Projet denqute Rapport de vote 32/187/DTR 32/188/RVC Le rapport de vo

46、te indiqu dans le tableau ci-dessus donne toute information sur le vote ayant abouti lapprobation de cet amendement. Le comit a dcid que le contenu de cette publication ne sera pas modifi avant la date de maintenance indique sur le site web de la CEI sous http:/webstore.iec.ch dans les donnes relati

47、ves la publication recherche. A cette date, la publication sera reconduite; supprime; remplace par une dition rvise; ou amende. _ Page 62 Remplacer le Tableau 6 existant par le nouveau tableau suivant: Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for

48、ResaleNo reproduction or networking permitted without license from IHS-,-,-TR 60943 Amend. 1 CEI:2008 7 Tableau 6 Valeurs types de limites dchauffement et de temprature* Dsignation de lorgane Colonne A Echauffementmaximal Ku(an= 20 C) Colonne B Temprature maximale C (an= 40 C) Remarques Contacts lastiques Cuivre et alliage de cuivre, nus dans GOt dans le GNOt dans lhuile Etams dans, GO