IEC 60317-17-2010 Specifications for particular types of winding wires - Part 17 Polyvinyl acetal enamelled rectangular copper wire class 105《特种绕组线规范.第17部分 105级聚乙烯醇缩醛漆包扁铜线》.pdf

《IEC 60317-17-2010 Specifications for particular types of winding wires - Part 17 Polyvinyl acetal enamelled rectangular copper wire class 105《特种绕组线规范.第17部分 105级聚乙烯醇缩醛漆包扁铜线》.pdf》由会员分享，可在线阅读，更多相关《IEC 60317-17-2010 Specifications for particular types of winding wires - Part 17 Polyvinyl acetal enamelled rectangular copper wire class 105《特种绕组线规范.第17部分 105级聚乙烯醇缩醛漆包扁铜线》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60317-17Edition 3.0 2010-03INTERNATIONAL STANDARD NORME INTERNATIONALESpecifications for particular types of winding wires Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105 Spcifications pour types particuliers de fils de bobinage Partie 17: Fil de section rectangulaire en

2、cuivre maill avec actal de polyvinyle, classe 105 IEC60317-17:2010 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mec

3、hanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the a

4、ddress below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la ph

5、otocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national

6、 de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all

7、 electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.i

8、ec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publi

9、cations. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with e

10、quivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or cont

11、act us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies appa

12、rentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Cata

13、logue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les n

14、ouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes e

15、t dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette public

16、ation ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60317-17Edition 3.0 2010-03INTERNATIONAL STANDARD NORME INTERNATIONALESpecifications for particular types of winding wires Part 17: Polyvinyl ace

17、tal enamelled rectangular copper wire, class 105 Spcifications pour types particuliers de fils de bobinage Partie 17: Fil de section rectangulaire en cuivre maill avec actal de polyvinyle, classe 105 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE JICS 29.060.10

18、PRICE CODECODE PRIXISBN 2-8318-1083-0 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 60317-17 IEC:2010 CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Terms, definitions and general notes

19、on methods of test and appearance 7 3.1 Terms and definitions 7 3.2 General notes on methods of test7 3.3 Appearance.7 4 Dimensions 7 5 Electrical resistance .7 6 Elongation 7 7 Springiness 7 8 Flexibility and adherence7 8.1 Mandrel winding test .7 8.2 Stretching test.7 9 Heat shock .8 10 Cut-throug

20、h 8 11 Resistance to abrasion .8 12 Resistance to solvents8 13 Breakdown voltage .8 14 Continuity of insulation .8 15 Temperature index .8 16 Resistance to refrigerants.8 17 Solderability .8 18 Heat or solvent bonding8 19 Dielectric dissipation factor.8 20 Resistance to transformer oil 9 21 Loss of

21、mass 9 23 Pin hole test .9 30 Packaging 9 Table 1 Mandrel winding 7 60317-17 IEC:2010 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105 FOREWORD 1) The International Electrotechnic

22、al Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this e

23、nd and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Com

24、mittee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in a

25、ccordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all

26、 interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held re

27、sponsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any diverg

28、ence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC ma

29、rks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual exper

30、ts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Pu

31、blication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Pu

32、blication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. This International Standard has been prepared by IEC technical committee 55: Winding wires. This third edition of IEC 60317-17 cancels and replaces the second edition issue

33、d in 1990, its Amendment 1 (1997) and its Amendment 2 (2005). This edition constitutes a technical revision. The main change with respect to the previous edition is listed below: Clause 20: reference to the transformer oil resistance test method in IEC 60851-4. 4 60317-17 IEC:2010 The text of this s

34、tandard is based on the following documents: FDIS Report on voting 55/1180/FDIS 55/1191/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives,

35、 Part 2. This International Standard is to be read in conjunction with IEC 60317-0-2 (1997). A list of all the parts in the IEC 60317 series, under the general title Specifications for particular types of winding wires, can be found on the IEC website. The committee has decided that the contents of

36、this amendment and the base publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended.

37、 60317-17 IEC:2010 5 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing 1) winding wires and test methods (IEC 60851); 2) specifications for particular types of winding wire (IEC 60

38、317); 3) packaging of winding wires (IEC 60264). 6 60317-17 IEC:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105 1 Scope This part of IEC 60317 specifies the requirements of enamelled rectangular copper winding wire of c

39、lass 105 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to

40、enhance certain performance or application characteristics. Class 105 is a thermal class that requires a minimum temperature index of 105 and a heat shock temperature of at least 155 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is r

41、ecommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor dimensions covered by this standard is width: min. 2,00 mm max. 16,00 mm; thickness: min. 0,80 mm max. 5,60 mm. Wires of grade 1 and grade 2 are include

42、d in this specification and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specified ratio width/thickness are given in IEC 60317-0-2. 2 Normative references The following referenced documents are indispensable for the application of this

43、document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-2:1997, Specifications for particular types of winding wires Part 0-2: General requirements Enamelled rectangular copp

44、er wire Amendment 1 (1999) Amendment 2 (2005) IEC 60851-4:1996, Methods of test for winding wires Part 4: Chemical properties Amendment 1 (1997) Amendment 2 (2005) 60317-17 IEC:2010 7 3 Terms, definitions and general notes on methods of test and appearance 3.1 Terms and definitions For terms and def

45、initions, see 3.1 of IEC 60317-0-2. In case of inconsistencies between IEC 60317-0-2 and this standard, IEC 60317-17 shall prevail. 3.2 General notes on methods of test For general notes on methods of test, see 3.2 of IEC 60317-0-2. In case of inconsistencies between IEC 60317-0-2 and this standard,

46、 IEC 60317-17 shall prevail. 3.3 Appearance See 3.3 of IEC 60317-0-2. 4 Dimensions See Clause 4 of IEC 60317-0-2. 5 Electrical resistance See Clause 5 of IEC 60317-0-2. 6 Elongation See Clause 6 of IEC 60317-0-2. 7 Springiness See Clause 7 of IEC 60317-0-2. 8 Flexibility and adherence 8.1 Mandrel wi

47、nding test The coating shall show no crack after the wire has been bent flatwise and edgewise on a mandrel with a diameter as specified in Table 1. Table 1 Mandrel winding Wire bent on Mandrel diameter Width Sizes up to and including 10 mm Sizes over 10 mm 2 width 3 width Thickness All dimensions 2

48、thickness 8.2 Stretching test The wire shall be stretched by 20 %. 8 60317-17 IEC:2010 The distance of loss of adhesion shall be less than 1x width. 9 Heat shock See Clause 9 of IEC 60317-0-2, where the minimum heat shock temperature shall be 155 C. 10 Cut-through Test inappropriate. 11 Resistance t

49、o abrasion Test inappropriate. 12 Resistance to solvents See Clause 12 of IEC 60317-0-2. 13 Breakdown voltage See Clause 13 of IEC 60317-0-2, where the elevated temperature shall be 105 C. 14 Continuity of insulation Test inappropriate. 15 Temperature index See Clause 15 of IEC 60317-0-2, where the minimum temperature index shall be 105. 16 Resistance to refrigerants Test inappropriate. 1