SAE AS 7513-2017 MALE FERRULE THREADLESS - FLEXIBLE FIXED CAVITY CURRENT CARRYING SELF BONDING SWAGED.pdf

《SAE AS 7513-2017 MALE FERRULE THREADLESS - FLEXIBLE FIXED CAVITY CURRENT CARRYING SELF BONDING SWAGED.pdf》由会员分享，可在线阅读，更多相关《SAE AS 7513-2017 MALE FERRULE THREADLESS - FLEXIBLE FIXED CAVITY CURRENT CARRYING SELF BONDING SWAGED.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD MALE FERRULE, THREADLESS, - FLEXIBLE, FIXED CAVITY, CURRENT CARRYING, SELF BONDING, SWAGED AS7513Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electron

2、ic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2017-09

3、THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3A FEDERAL SUPPLY CLASS 4730 AS7513 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: AS7510 /4/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sciences. The useof this report is entirely

4、voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is the sole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites y

5、our written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS7513 RATIONALE NEW PART STANDARD AS PART OF AS7510 TO SUPERSEDE AS5833. FIGURE 1 SECTION A-A AEROSPACE STANDARD AS7513 SHEET 2 OF 3 MALE FERRULE, THREADLES

6、S, - FLEXIBLE, FIXED CAVITY, CURRENT CARRYING, SELF BONDING, SWAGED TABLE 1 DIMENSIONS AND WEIGHTS /6/ BASIC NO AS7513 /12/ SIZE CODE NOM TUBE SIZE REF A .003 B .010 C D REF E .002 F .001 H .005 M N W +.000 -.010 LB/EA REF ALUM 08 .500 .507 .704 .170 .6225 .480 .007 .531 3 4 .117 .01 10 .625 .633 .7

7、04 .170 .7475 .607 .007 .654 3 4 .117 .01 12 .750 .758 .754 .220 .8875 .732 .007 .782 3 4 .105 .02 16 1.000 1.008 .804 .245 1.1395 .983 .008 1.001 4 5 .111 .02 20 1.250 1.259 .804 .245 1.3895 1.233 .008 1.252 4 5 .111 .03 24 1.500 1.509 .866 .245 1.6395 1.478 .009 1.521 5 6 .150 .03 28 1.750 1.759 .

8、866 .245 1.8895 1.728 .009 1.770 5 6 .150 .04 32 2.000 2.009 .896 .245 2.1425 1.979 .009 2.042 5 6 .150 .04 36 2.250 2.259 .927 .245 2.3925 2.229 .009 2.290 5 6 .150 .05 40 2.500 2.510 .927 .265 2.6425 2.479 .011 2.538 5 6 .150 .06 48 3.000 3.010 .927 .265 3.1425 2.977 .011 3.035 5 6 .150 .07 56 3.5

9、00 3.512 .957 .265 3.6425 3.479 .012 3.547 6 7 .150 .08 64 4.000 4.012 1.140 .265 4.1515 3.979 .013 4.050 7 8 .150 .11 NOTES /1/ MATERIAL: MATERIAL CODE LETTER A TYPE 2024-T351, T851, T8510, OR T8511 ALUMINUM ALLOY PER AMS-QQ-A-225/6, AMS4120, AMS4339, AMS-QQ-A-200/3, ASTM B211, OR ASTM B241. 2. HEA

10、T TREATMENT: MATERIAL CODE LETTER A IF THE MATERIAL IS PROCURED IN THE SOLUTION TREATED CONDITION, AGE TO THE T851 OR T8511 PER AMS2770 OR AMS2772. 3. FINISH: MATERIAL CODE LETTER A CHEMICAL CONVERSION COAT PER MIL-DTL-5541, TYPE 1, CLASS 3. /4/ QUALIFICATION: FERRULES MANUFACTURED TO THIS SPECIFICA

11、TION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL)FOR PRI-QPL-AS7510 FOR THIS STANDARD. THE QPL IS AVAILABLE AT www.eAuditN. /5/ IDENTIFICATION: MARK PER AS478-15A OR AS478-30 USING .062 OR LARGER CHARACTERS. MARK A

12、S A MINIMUM THE MANUFACTURERS NAME, AND/OR CAGE CODE, COMPLETE “AS” NUMBER AND DATE OF MANUFACTURE IN ACCORDANCE WITH MIL-STD-130. SIZES 20 AND SMALLER MAY BE INDIVIDUALLY BAGGED WITH A TAG PER AS478-35D CONTAINING THE PREVIOUS INFORMATION. /6/ OTHER DIMENSIONS AND TOLERANCES NOT SPECIFIED ARE CONTR

13、OLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPATIBILITY WITH THE ASSEMBLY AND COMPLIANCE WITH THE REQUIREMENTS OF THE PROCUREMENT SPECIFICATION. 7. INTERPRETATION OF DRAWING PER AS4296. 8. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHER

14、WISE SPECIFIED, MACHINED SURFACE TO BE 125 MICROINCHES Ra. 9. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 10. DIMENSION AND TOLERANCE PER ASME Y14.5-2009. 11. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: .005, ANGULAR DIMENSIONS 030. AEROSPACE STANDARD AS7513 SHEET 3 OF 3

15、MALE FERRULE, THREADLESS, - FLEXIBLE, FIXED CAVITY, CURRENT CARRYING, SELF BONDING, SWAGED /12/ FORMAT OF PART NUMBER: AS7513 A 32 BASIC PART NUMBER MATERIAL CODE LETTER /1/ SIZE CODE, TUBE SIZE IN .062 INCH INCREMENTS (SEE TABLE 1) EXAMPLE OF PART NUMBER: AS7513A32 /13/ AN IDENTIFYING MACHINED GROO

16、VE IS PLACED AT THE END OF THE FERRULE TO DIFFERENTIATE THE AS7513 FERRULES FROM THE AS5833 FERRULES. /14/ THE FERRULE DESIGN IS THE SAME AS THE AS5833 EXCEPT THE FERRULE LENGTH (DIMENSION “B”) IS LONGER AND THE DUCT STOP HEIGHT IS SHORTER TO PREVENT THE DUCT STOP INTERFERING THE SWAGING OPERATION.

17、SPECIFICATION NOTES 1. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.