NAVY MIL-G-29635-1990 GLOVES FIREMEN-S STRUCTURAL ALUMINIZED PROXIMITY《结构接近覆铝的消防手套》.pdf

《NAVY MIL-G-29635-1990 GLOVES FIREMEN-S STRUCTURAL ALUMINIZED PROXIMITY《结构接近覆铝的消防手套》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-G-29635-1990 GLOVES FIREMEN-S STRUCTURAL ALUMINIZED PROXIMITY《结构接近覆铝的消防手套》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-G-29635 BL( W 9977906 OL(588q3 T m INCH-POUND MIL-G-29635 20 November 1990 MILITARY SPECIFICATION GLOVES, FIREMENS, STRUCTURAL/ALUMINIZED PROXIMITY This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers t

2、he requirements for a flame resistant combination structural/aluminized proximity firemens glove. 1.2 Classification. The gloves shall be of one type only and in the following sizes (see 6.2). X-Small (XS) Small (8) Medium (M) Large (L) X-Large (XL) 2. APPLICABLE DOCUMENTS 2.1 Government documents.

3、Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: OEficer in Charge, Navy Clothing and Textile Research Facility, P.O. Box 59, Natick, MA 01760-0001 by using the self-addressed Standardization Doc

4、ument Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-29

5、b35 q W 9994906 0458844 I M MIL-G-29635 2.1.1 Specifications, standards, and handbooks. The following specifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of t

6、he Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL KK-L-2004 NN-P-71 DDD- L- 20 MILITARY MIL-C-3735 MIL-P-15011 MIL-B-17757 MIL-C-21852 MIL-C-24941 MIL-C-24929 MIL-T-44100 MIL-C-87059 STANDARDS F

7、EDERAL FED-STD-191 FED-STD-311 FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 MIL-STD-2073-1 MIL-STD-2073-2 - Leather, Cattlehide, Deerskin and Horsehide, Chrome - Pallet, Material Handling, Wood, Stringer - Label; for Clothing, Equipage and Tentage (General Tanned Construction, 2-Way and

8、4-Way (Partial) . Use) - Cuffs, Knit, Wrist and Ankle, and Cloth, Knitted - Pallets, Material Handling, Wood, Post - Box, Shipping, Fiberboard (Modular Sizes) - Cloth, Taffeta, Nylon - Cloth, Laminated, Aluminized (Para-aramid base) - Cloth, Laminated, Aluminized (Para-aramid/PBI base) - Thread, Par

9、a-aramid, Spun, Intermediate, Modulus - Cloth, Knitted, Nylon, Tricot Construct ion, 4-Way Entry - Textile Test Methods - Leather, Methods of Sampling and Testing - Stitches, Seams, and Stitchings - Sampling Procedures and Tables for Inspection by - Marking for Shipment and Storage - Palletized Unit

10、 Loads - DOD Materials Procedures for Development and - Packaging Requirement Codes Attributes Application of Packaging Requirements (Unless otherwise indicated, copies of federal and military specification, standards, and handbooks are available from the Standardization Documents Order Desk, Buildi

11、ng 4D, 700 Robbins Avenue? Philadelphia, PA 19111-5094.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-27b35 9 0 7777906 0958895 3 W MIL-G-29635 2.1.2 Other Government documents, drawings, and publications. The following other Government do

12、cuments, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues aye those cited in the solicitation. U.S. POSTAL MANUAL (Copies of the manual may be obtained from the Superintendent of Documents, U.S. Government Printing Office,

13、 Washington, DC 20402-0001.) 2.2 Non-Government publications. The following document(s) form a part of this specification to the extent specified herein. Unless otherwise specified, the issue of documents which are DoD adopted shall be those listed in the issue of the DODISS cited in the solicitatio

14、n. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applications for copies should be addressed to the Ameri

15、can Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404.) UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Application for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chica

16、go, IL 60606-5808.) NATIONAL FIRE PROTECTION ASSOCIATION NFPA 1973 - Gloves for Structural Firefighting (Applications for copies should be addressed to the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.) AMERCIAN SOCIETY FOR TESTING AND MATERIALS ASTM E-96 - Water Vapor T

17、ransmission of Materials ASTM D1424 - Tear Resistance of Woven Fabrics by Falling Pendulum (Elmendorf) Apparatus (Applications for copies should be addressed to the Amercian Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publica

18、tions are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-2963

19、5 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIRE

20、MENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the sample in which case this specification shall govern. 3- 3.2 First article. When specified, the contractor shall furnish sample u

21、nit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Material. l_l -I MIL-G-27b35 3.3.1 Leather. The palm area shall be a blue/gray chrome tanned flesh split cattlehide conforming to type VI11 of KK-L-2004. The leather shall be a 3 to 3-1/2 ounce thickness after silicone treatment

22、 specified in 3.3.1.1 except that: a. b. Test for percent ash and chloroform soluble material are not required. Shrinkage temperature shall not be less than 105C. 3.3.1.1 Silicone treatment. The leather shall be treated with an approved durable silicone compound (see 6.4) to lower its water absorpti

23、on. The treated leather shall not absorb more than 30 percent water when tested as specified in 4.4.1. 3.3.2 Aluminized shell. The aluminized shell for the back of the glove shall be either of the following fabrics: A highly reflective aluminum surface laminated to a knitted para-aramid base fabric

24、conforming to Type II of MIL-C-24929 or a highly reflective aluminum surface laminated to a knitted para-aramid/PBI base fabric conforming to MIL-C-24941. 3.3.3 Liner. 3.3.3.1 Liner material. The material used in the glove lining shall be a 40/35/25 (+ 2.5%) blend of para-aramid, PFR rayon and PBI (

25、polybenzimidazole). The liner material shall be made by using a 3 bar rashel knitting machine. The front and back bars shall be 32 singles consisting of 40/60 PBI/para-aramid; and the middle bar shall be 15 singles consisting of PFR rayon. The technical back shall be napped (the side of the fabric t

26、hat the rayon yarns are predominant). The use of fibers other than the approved is prohibited. The cloth shall conform to the physical requirements listed above and in Table I when tested as specified in 4.4.1. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

27、om IHS-,-,-MIL-G-27635 4 W 7779706 045Ll7 7 W MIL-G-29635 . Table I - Physical Requirements _ Characteristics Mi ni mum Maximum Wales per inch 20 Courses per inch 20 Tear strength - lbs (N) Wale 10 (44.5) Course 8 (35.6) Weight - oz/yd2 (g/m2) 8.0 (271.2) Bursting strength - lbs (N) 90 (400.5) Flame

28、 resistance, vertical (Wale direction only) After flame time, seconds Char length, inches (cm) After glow, seconds 0.5 1 (2.54) 15 3.3.3.2 Para-aramid. The fiber shall be 1-112 denier, 2 inch staple, when tested as specified in 4.4.1. 3.3.3.3 Rayon. The PFR (permanently flame retardant) rayon is man

29、ufactured by metering water-insoluble phosphorous-base chemical compounds into viscose solution from which rayon fibers are spun. The fibers contain the flame retardant which is highly dispersed in a matrix of PFR cellulose. The fiber shall be a nominal 1.5 - 2.0 denier and nominal 1.5 - 2.0 inch st

30、aple cut length, when tested as specified in 4.4.1. 3.3.3.4 PBI. The fiber shall be 1-112 denier, 2 inch staple, when tested - as specified in 4.4.1. 3.3.3.5 Color. The color shall be natural. 3.3.3.6 Knit construction. The guide bar stitch pattern shall be as follows when tested as specified in 4.4

31、.1. 2 . 321 O ic: . 543210 $ 210 Bar #1 Bar #2 Bar #3 Front guide bar #1: 1-0/2-3 Middle guide bar #2: O-0/5-5 Back guide bar #3: 1-2/1-O 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-29635 3.3.4 Insert. The glove insert shall be made of. n

32、ylon tricot fabric conforming to MIL-C-87059, except the construction shall have a minimum of 36 wales and 24 courses per inch. The fabric shall have a waterproof, moisture vapor permeable barrier (membrane, coating or laminate) applied such that the barrier is orientated toward the hand in the glov

33、e. The insert and sealed seam shall meet the following requirements when tested in accordance with 4.4.1. Characteristic Requirement Water penetration resistance (psi) - Minimum 4.0 Moisture vapor transmission rate (g/m2/24 hr) - Minimum 400 3.3.5 Cuff. The fabric used for the cuff shall be in accor

34、dance with type IV, class 3 of MIL-C-3735, except the yarn shall consist of 60% para-aramid and 40% PBI (polybenzimidazole). The fabric shall meet the following requirements when tested in 4.4.1. Characteristic Flame resistance After flame (seconds) - Maximum After glow (seconds) - Maximum Char leng

35、th - inches (cm) - Maximim Requirement 2.0 8.0 4.0 (10.16) 3.3.6 Adhesive. The adhesive used to bond the inside of the insert fingertips to the lining shall be compatible with the materials utilized. 3.3.7 Thread. The thread for assembling the glove shall be a para-aramid spun staple thread, size T-

36、70, minimum of 4 ply, natural color conforming to MIL-T-44100. 3.3.8 Label. Each glove shall have a combination warning, size, identification, instruction label conforming to type VI, class 14 of DDD-L-20, except that colorfastness requirements shall not apply. The label shall have the following for

37、mat and inscription: GLOVES, FIREMENS, STRUCTURAL/ALUMINIZED PROXIMITY SIZE: MEDIUM OR M (EXAMPLE) NAME OF CONTRACTOR: NAME OF MANUFACTURER: (IF OTHER THAN CONTRACTOR) CONTRACT NO: DLA-100-00-000-0000 (EXAMPLE) STOCK NO: 8415-00-000-0000 (EXAMPLE) WARNING DO NOT KEEP IN DIRECT CONTACT WITH FLAME KEE

38、P CLEAN, SOILING WILL REDUCE PROTECTIVE QUALITIES HAND WASH IN COLD WATER WITH LIQUID SOAP DO NOT BLEACH AIR DRY ONLY 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-29635 4 m 9999906 0458849 O m MIL-G-29635 . 3.4 Design. The glove shall be f

39、ive fingered, gunn cut, with a straight thuinb and knit wristlet. Palm shall be leather, and back shall be aluminized fabric, with aluminized side on the outside. A waterproof moisture vapor permeable glove insert shall be sandwiched between the inseamed shell and napped knitted lining. 3.4.1 Figure

40、s. Figures are furnished for information purposes only. When inconsistancies exist between the written specification and the figure, the written document shall govern. - 3.5 Patterns. Standard patterns to be used to cut working patterns will be furnished by the Government (see 6.3). The working patt

41、erns shall be identical to the Government patterns. Neither the Government patterns nor the working patterns shall be altered in any way, except that additional notches for use during construction are permitted on the working patterns. Also, minor modifications are permitted where necessary when usi

42、ng automatic equipment. These modifications shall not alter the dimensional, serviceability, or appearance requirements cited in the specification. The seam allowance shall be 1/8 inch. 3.5.1 Pattern parts. The component parts shall be cut from the materials as specified, and in accordance with the

43、following list of pattern parts: Ma ter ia1 Pattern parts Cut parts Leather shell- Aluminized shell Knit liner Palm Thumb Fingers Back Wrist tab Back liner Palm liner Thumb liner Finger liner 3.6 Construction, 3.6.1 Stitches, seams and stitchings. Stitch, seam and stitching types specified in Table

44、II shall conform to FED-STD-751. Whenever two or more methods for seam or stitch types are given for the same part of the operation any one may be used. Seam allowance shall be maintained with seams sewn so that no raw edges, runoffs, twists, pleats, puckers or open seams result. All seams shall sta

45、rt and finish evenly. Thread tension shall be maintained so that there is no tight or loose stitching. The bight of the overedge stitching shall be 3/16 inch. The guide and knife shall be set to trim only the ravelled ends of the fabric. In order to minimize the size of the needle hole in the leathe

46、r, the needle used in the seaming operations shall be of the smallest size which will accomodate the specified size of thread. 3.6.2 Stitches per inch. The minimum and maximum number of stitches per inch shall be as specified in Table II. 7 Provided by IHSNot for ResaleNo reproduction or networking

47、permitted without license from IHS-,-,-MIL-G-29b35 q 7999906 0458850 7 MIL-G-29635 3.6.3 Thread breaks and ends of seams. Ends of al.1. seams and stitching produced with 301 stitch type, when not caught in other seams or stitching, shall be securely tacked or backstitched not less than 3/8 inch. Thr

48、ead breaks (all stitch types) or bobbin run-outs shall be secured by stitching back of the break not less than 1/2 inch. 3.6.4 Cutting. The leather shall be examined on both sides prior to cutting and any area that contains surface defects shall not be included in the cut leather parts. The commerci

49、al method of pre-measuring and adjusting the stretch of the skin to provide measurements for the cut tranks, thumb, and fingers will be permitted provided the finished measurements of Table III are maintained. Skins shall not be toggled and set whereby all stretch of the leather is eliminated. Tranks and cut parts shall be matched for color, grain, and thickness of leather. 3.7 Manufacturing operations requirements. The glo