INTERN CEMS GT-30-2009 Chipping and Salt Spray Resistance《耐崩裂性和耐盐雾性》.pdf

《INTERN CEMS GT-30-2009 Chipping and Salt Spray Resistance《耐崩裂性和耐盐雾性》.pdf》由会员分享，可在线阅读，更多相关《INTERN CEMS GT-30-2009 Chipping and Salt Spray Resistance《耐崩裂性和耐盐雾性》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 1 of 2 NAVISTAR, INC. CEMS (CORPORATE ENGINEERING MATERIAL SPECI

2、FICATION) NUMBER: CEMS GT30 TITLE: Chipping and Salt Spray Resistance REVISION: August 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering DATE ISSUED: August 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazard

3、ous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: R

4、eplaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive. Reference: File 30-1 1.0 APPLICATION This specification covers the evaluation the ability of the paint to adhere to metal parts after being subjected to chipping or scribing, then salt spray. 2.0 SCOP

5、E This specification describes the test method of chipping and salt spray testing. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards applies. The following specifications, standards, and regulations are referenced herein. CEMS GT28 SAE J400 ASTM B 117 A

6、STM D 1654 4.0 APPARATUS 4.1 Q.G.R. Gravelometer machine capable of reaching 80 psi. 4.2 A straight-shank tungsten carbide tip, lathe cutting tool with an angle of 60 +/- 15 . 4.3 A freezer capable of maintaining a temperature of -30 C (-22 F) within +/- 3 C (+/- 5 ). 5.0 MATERIAL 5.1 3” x 6” bumper

7、 coupons or a bumper section with the appropriate paint. 5.2 3M Permacel 99 adhesive tape. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: CEMS GT30 TITLE Chipping and Sal

8、t Spray Resistance REVISION: August 2009 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 2 of 2 6.0 PROCEDURE 6.1

9、 Place one of the metal coupons or parts in the freezer at -30 C (-20 F) within +/- 3 C (+/- 5 F) for one hour, while keeping the other coupons or parts at 21 to 27 C (70 to 80 F) room temperature. 6.2 After one hour, remove the coupons or parts from the freezer and test in the Q.G.R. Gravelometer p

10、er SAE J400. 6.3 Test the coupons at room temperature in the Q.G.R. Gravelometer per SAE J400. 6.4 Examine both sets of panels for excessive chipping per CEMS GT-28. 6.5 Using the lathe cutting tool at a 45 angle, scribe the third set of coupons or parts per ASTM D 1654. 6.6 Place all three sets of

11、coupons or parts in the salt spray chamber and test per ASTM B117 for 50 hours. 6.7 Within 15 minutes of removing the pieces form the salt spray chamber, rinse the specimens with water. 6.8 Using a metal piece or a dull knife, vigorously scrape over the scribe or gravel chips while under the stream

12、of water per ASTM D 1654. 6.9 Place the 3M Permacel 99 adhesive tape over the scribe or gravel marks to remove any loose paint from the metal. 6.10 Examine the coupons or parts for evidence of creapage from the scribe or gravel chips. 6.2 REPORT Report as pass or fail per CEMS GT-28. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-