FORD WSK-M2G299-B2-2016 ADHESIVE SEALER SYNTHETIC RUBBER HOT APPLIED 120 - 130 NON-REACTIVE TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M2G299-B1).pdf

《FORD WSK-M2G299-B2-2016 ADHESIVE SEALER SYNTHETIC RUBBER HOT APPLIED 120 - 130 NON-REACTIVE TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M2G299-B1).pdf》由会员分享，可在线阅读，更多相关《FORD WSK-M2G299-B2-2016 ADHESIVE SEALER SYNTHETIC RUBBER HOT APPLIED 120 - 130 NON-REACTIVE TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M2G299-B1).pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 05 2016 05 27 Revised See Summary of Revisions J.Herl, FoE 2015 01 07 N Status B4 N Status - No replacement named L. Sinclair, NA 1990 09 03 Released B1 and B2 Released K. Wolters, FOE Controlled document at www.MATS Copyright 2016, Ford

2、 Global Technologies, LLC Page 1 of 7 ADHESIVE, SEALER, SYNTHETIC RUBBER, HOT APPLIED, WSK-M2G299-B1 60 - 70 C, HEAT CURING, MEDIUM STRENGTH ADHESIVE, SEALER, SYNTHETIC RUBBER, HOT APPLIED, WSK-M2G299-B2 120 - 130 C, NON-REACTIVE ADHESIVE, SEALER, SYNTHETIC RUBBER, HOT APPLIED, WSK-M2G299-B3 70 - 80

3、 C, HEAT CURING NOT TO BE USED FOR NEW DESIGN ADHESIVE, SEALER, SYNTHETIC RUBBER, WARM APPLIED, WSK-M2G299-B4 30 - 60 C, HEAT CURING NOT TO BE USED FOR NEW DESIGN ADHESIVE, SEALER, SYNTHETIC RUBBER, COLD APPLIED, WSK-M2G299-B5 15 - 35 C, HEAT CURING NOT TO BE USED FOR NEW DESIGN ADHESIVE, SEALER, RU

4、BBER BASED, WARM APPLIED, WSS-M2G299-B6 30 50 C, HEAT CURING NOT TO BE USED FOR NEW DESIGN ADHESIVE, SEALER, SYNTHETIC RUBBER, EXPANDABLE, WSK-M2G299-B7 COLD APPLIED, 15 - 35 C, HEAT CURING NOT TO BE USED FOR NEW DESIGN ADHESIVE, SEALER, SYNTHETIC RUBBER, WARM APPLIED WSS-M2G299-B8 60 - 70 C, HEAT C

5、URING, LONG TERM FLEXIBLE 1. SCOPE The materials defined by these specifications are solvent free, spot weldable adhesives and sealers. 2. APPLICATION These specifications were released originally for materials used to bond sheet metal body parts. The materials are applicable on oiled surfaces with

6、acceptable oil film weights (European applications limit the oil/pre-lubricant film weight to max 3 g/m, see para. 3.20). Note: Care must be taken to ensure that the local oil film weight in the area of the adhesive/sealer application does not exceed the critical limit. Monitoring of the film thickn

7、ess, adequate storage of the part and/or cleaning of the surface prior to sealer/adhesive application is necessary to avoid critical film thickness values, which would then cause malfunction of the sealer/adhesive. ENGINEERING MATERIAL SPECIFICATION WSK-M2G299-B1/B2/B3/B4/B5/B7 WSS-M2G299-B6/B8 Copy

8、right 2016, Ford Global Technologies, LLC Page 2 of 7 WSK-M2G299-B1 is used where high shear strength is required, e.g. bonding of hood parts. It cures during the electrocoat baking process at 175 C. WSK-M2G299-B2 is used to seal rear wheelhouse to side panel, roof bow to roof, frame of sliding roof

9、 to roof etc. It does not cure. WSK-M2G299-B3 is used to seal rear wheelhouse to side panel, roof bow to roof, frame of sliding roof-to-roof etc. It cures during the electrocoat baking process at 175 C. WSK-M2G299-B4 is used to bond reinforce panel to door panel etc. It cures during electrocoat baki

10、ng process at 175 C. WSK-M2G299-B5 is used to bond rear wheel arch outer to inner panel plus fuel filler. It cures during electrocoat baking process at 175 C. WSS-M2G299-B6 is used to bond roof bow to roof, etc. It cures during the electrocoat baking process at 175 C. WSK-M2G299-B7 is used to bond r

11、ear wheel arch outer to inner panel plus fuel filler. It is applied with swirl spray system. It cures during electrocoat baking process at 175 C. WSS-M2G299-B8 is used where high shear strength and long term flexible properties are required, e.g. bonding of hood parts. It cures during the electrocoa

12、t baking process at 175 C. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other d

13、ocuments. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 COLOR Black or grey 3.3 DENSITIY AT 20 C See Initial Sample (ASTM D792) +/- 0.05 g/cm3 3.4 SOLIDS 99.0 % min (FLTM BV 150-10) 3.5 ASH 47.0% max (FLTM BV 150-10) 3.6 WATER

14、ABSORPTION 1% max (FLTM BV 153-07 Method A, Exception: Cure according to Para 4.4 (electrocoat only) ENGINEERING MATERIAL SPECIFICATION WSK-M2G299-B1/B2/B3/B4/B5/B7 WSS-M2G299-B6/B8 Copyright 2016, Ford Global Technologies, LLC Page 3 of 7 3.7 SHEAR ADHESION, N/cm2 Cohesion failure (FLTM BV 154-03,

15、Method B) Prepare test specimens according to section A for oiled surfaces and para 3.20, coating thickness 3.0 mm for B1-B4/B6 and B8 and 0.2 mm for B5 and B7 Cure according to Para 4.4 B1 B2 B3 B4 B5 B6 B7 B8 3.7.1 At 23 +/- 2 C, min 80.0 3.0 3.0 20.0 400 12.0 900 80 3.7.2 At 90 +/- 2 C, min 40.0

16、0.5 1.0 10.0 90.0 8.0 550 40 3.7.3 At -30 +/- 2 C, max 80.0 3.0 3.0 20.0 450 20.0 850 90-225 3.8 PEEL ADHESION, N/cm, min Cohesion failure (FLTM BV 154-03, Method C) Prepare test specimens according to section A for oiled surfaces and para. 3.20, coating thickness 3.0 mm for B1-B4/B6 and B8 and 0.2

17、mm for B5 and B7. Cure according to Para 4.4 B1 B2 B3 B4 B5 B6 B7 B8 3.8.1 At 23 +/- 2 C, min 80.0 10.0 10.0 25.0 140 11.0 400 70 3.8.2 At 90 +/- 2 C, min 70.0 4.0 4.0 15.0 80 9.0 200 60 3.8.3 At -30 +/- 2 C, max 250 45.0 45.0 45.0 210 15.0 260 75-175 3.9 HARDNESS DUROMETER A 60 -75 NA 8 5-15 75 13

18、90 60-70 (ISO 868, 3 s dwell) Test Method: Prepare a test panel (300 x 100 x 0.8 -0.9 mm) according to FLTM BZ 150-01 see para 3.20. Apply a ribbon of test material (250 x 30 x 5 mm) to the Test Panel. Conditioning: 10 minutes at 23 +/- 2 C Baking: 30 minutes at 175 +/- 2 C Conditioning: 4 h at 23 +

19、/-2 C ENGINEERING MATERIAL SPECIFICATION WSK-M2G299-B1/B2/B3/B4/B5/B7 WSS-M2G299-B6/B8 Copyright 2016, Ford Global Technologies, LLC Page 4 of 7 3.10 FLEXIBILITY AFTER AGING No loss of adhesion (FLTM BV 153-04, Method 4 3b, exceptions noted below) and no chipping Cure according to Para 4.4 Test pane

20、l dimensions: 300 x 100 x 0.8 - 0.9 mm Aging: 14 days at 80 +/ -2 C Conditioning: 2 h at 23 +/-2 C Test Temperature: -30 +/- 2 C Mandrel diameter: 100 mm 3.11 FLAMMABILITY Self extinguishing within 5 s. (FLTM BV 159-02, Method A, exceptions noted below) No corrosion allowed Material Thickness: 1.0 -

21、 1.2 mm Immediately after welding, separate the welded parts using a test fixture according to FLTM BV 159-01, Fig. 4. 3.12 CORROSION RESISTANCE No corrosion or blistering at the border line sealer/EC/steel The material shall protect the test panel from corrosion. Test Method: (a) Test panel prepara

22、tion according to FLTM BV 159-02, Method A. (b) After 2 h at 23 +/- 2 C wash, phosphate and electrocoat test assemblies under normal production conditions. (c) Cure test assemblies according to FLTM BV 150-05, Table 2: a. min curing cycle b. max curing cycle (d) Expose test assembly to Ford 00.00-L-

23、467 for 6 weeks (e) Separate welded assemblies using a test fixture according to FLTM BV 159-01, Fig. 4 and examine. Under the material and at the border line of material edges there shall be no visible corrosion, flaking, or any evidence of loss of adhesion of the material. 3.13 RESISTANCE AGAINST

24、WASH AND No dissolution PHOSPHATING SOLUTION of material or lifting from panel Test Method: Prepare a test panel (300 x 100 x 0.8 -0.9 mm) according to FLTM BZ 150-01 see para 3.20. Apply a ribbon of test material (250 x 30 x 5 mm) to the panel. Condition for 2 h at 23 +/- 2 C. Then wash, phosphate

25、and electrocoat the test panel under defined process conditions according to Global Manufacturing Standard UC 800. ENGINEERING MATERIAL SPECIFICATION WSK-M2G299-B1/B2/B3/B4/B5/B7 WSS-M2G299-B6/B8 Copyright 2016, Ford Global Technologies, LLC Page 5 of 7 3.14 FLOW RATE No flow permitted (FLTM BV 153-

26、01, Method A, exceptions noted below) Test Method: Prepare panels according to FLTM BZ 150-01 see para 3.20. Apply a bead of 8 mm diameter and bake 30 minutes at 110 +/- 2 C. 3.15 WETTING No discoloration or (FLTM BV 153-08, Method A) staining permitted The paint film (paint materials shall be noted

27、 in the Initial Sample Report of the adhesive, see also para 4.3) shall cover the sealer with a continuous film. 3.16 VOLUME EXPANSION Volume expansion is not mandatory. It shall be determined with the Initial Sample WSK-M2G299-B1/B4/B5/B7/B8 15 35% WSK-M2G299-B2/B3 25 40% WSS-M2G299-B6 60 150% Stru

28、cture after baking: If adhesive expands during the curing process, it shall form a closed skin. Any cellular structure shall be fine without large voids. The volume expansion shall be investigated under both minimum and maximum baking cycles per FLTM BV 150-05, Table 2. V2 - V1 It is defined as: Vol

29、ume Expansion = - x 100% V1 Where: V1 = Volume of unbaked adhesive V2 = Volume of baked adhesive 3.17 QUALITY The adhesive shall be a smooth, homogeneous mixture, free from foreign materials. The material must be adaptable for application in accordance with the appropriate Ford Motor Company Process

30、 Specification and must be compatible with all related materials. 3.18 PENETRATION, mm (ASTM D5, 0.483 N total weight force, 5 s dwell time) B1 B2 B3 B4 B6 B8 3.18.1 Original at 20 +/- 2 C 12 - 17 4.0 - 7 9 - 16 10 - 15 3 - 5 19 - 23 3.18.2 After Aging (14 days at 30 +/- 2 C) 10 - 17 3.5 - 7 8 - 16

31、9 - 15 2 - 5 17 - 23 ENGINEERING MATERIAL SPECIFICATION WSK-M2G299-B1/B2/B3/B4/B5/B7 WSS-M2G299-B6/B8 Copyright 2016, Ford Global Technologies, LLC Page 6 of 7 3.19 VISCOSITY (for B5 and B7) (FLTM BV 103-01, nozzle 2 mm ID, conditioning time up to measurement: 30 minutes at test temperature) B5 B7 L

32、ine pressure, bar 4 4 3.19.1 As received, s 200 350 80 - 90 3.19.2 After Aging, s 200 450 80 - 125 3.20 OIL COMPATIBILITY & REFERENCE OIL (European Applications) All materials released to this specification must be applicable to oiled surfaces, including corrosion protection oil, wash oils, pre-lubr

33、icants, draw oils, hot melts etc. The approved products for use in Ford of Europe or the European brands are listed in the applicable approved source list (contact materials engineering for details). The supplier must confirm the compatibility of the adhesive/sealer material to these specific coatin

34、g materials in the appropriate lab tests listed in para 3 and - prior to vehicle production - in a line trial in cooperation with Ford manufacturing engineering. The lab test panels must be oiled with maximum permissible oil film thickness (see FLTM BZ 150-11 Oiling of Steel Surfaces). Reference oil

35、 for adhesive performance comparison is Fuchs Anticorit RP 4107S Attention: New compatibility tests are necessary if the oil grade of the affected part is changed! Nominal oil film weight is: 1 - 1.5 g/m The maximum permissible oil weight for full adhesive performance is: 3 g/m Note: All necessary a

36、ctions must be taken to prevent any local oil film weight exceeding 3 g/m in the area of adhesive/sealer application. Critical areas are the lowest positions of parts during transport/storage, e.g. door hem flanges or other oil trapping areas. Unacceptable oil collection will require appropriate sto

37、rage geometries (critical areas turned to top) or in-process cleaning operations prior to sealer/adhesive application. 3.21 LINE TRIAL The Engineering Performance Requirements defined in this specification are based upon laboratory coupon testing and define the minimum acceptance criteria for adhesi

38、ve performance. Prior to use, the adhesive must be evaluated under the production parameters of the relevant production line. The choice of substrates, stamping lubricants, stamping plant-processing conditions, assembly plant processing conditions and specific design application may affect adhesive

39、performance. Compliance with this specification does not guarantee the adhesive will function for all potential applications on a vehicle. Therefore materials being evaluated for approval to this specification shall be subjected to a production trial. Functional trial results must be approved by the

40、 affected assembly operation. Results shall be made available to Materials Engineering prior to material approval and release. ENGINEERING MATERIAL SPECIFICATION WSK-M2G299-B1/B2/B3/B4/B5/B7 WSS-M2G299-B6/B8 Copyright 2016, Ford Global Technologies, LLC Page 7 of 7 4. GENERAL INFORMATION The informa

41、tion given below is provided for clarification and assistance in meeting the requirements of these specifications. Contact for questions concerning Engineering Material Specifications. 4.1 STORAGE STABILITY (From date of manufacturing) WSK-M2G299-B1/B2/B3 12 months WSK-M2G299-B4/B5/B7 6 months WSS-

42、M2G299-B6/B8 6 months The material must be stable during storage in unopened drums out of direct sunlight at temperatures between 5 C and 32 C. 4.2 OPEN ASSEMBLY TIME As specified by (At the required operation temperature) the supplier Open assembly time is the maximum time interval from initial app

43、lication of the adhesive to the completion of the part assembly for bonding. 4.3 MATERIAL REFERENCE All related materials used for approval of adhesives according to this specification, e.g. paint materials or metallic substrates, shall be noted in the Initial Sample Report of the adhesive. 4.4 MATE

44、RIAL CURE SCHEDULE Cure at min and max temperature conditions following paint shop oven cycle times most appropriate to local conditions according to tables listed in FLTM BV 150-05. Record chosen cycle in the Sample Report of the adhesive 4.5 APPROVAL OF MATERIALS Suppliers desiring approval of the

45、ir materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating fu

46、ll compliance with all the requirements of the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Con

47、trol Plans, Certification testing) with Ford. 4.6 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect t

48、he materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SR

49、EA. ENGINEERING MATERIAL SPECIFICATION WSK-M2G299-B1/B2/B3/B4/B5/B7 WSS-M2G299-B6/B8 Copyright 2016, Ford Global Technologies, LLC Page 8 of 7 For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must b