FORD ESF-M1L34-A-2003 COPPER WIRE BATTERY CABLE - #6 GAGE TO BE USED WITH FORD WSS-M99P1111-A 《电池电缆用铜丝》.pdf

《FORD ESF-M1L34-A-2003 COPPER WIRE BATTERY CABLE - #6 GAGE TO BE USED WITH FORD WSS-M99P1111-A 《电池电缆用铜丝》.pdf》由会员分享，可在线阅读，更多相关《FORD ESF-M1L34-A-2003 COPPER WIRE BATTERY CABLE - #6 GAGE TO BE USED WITH FORD WSS-M99P1111-A 《电池电缆用铜丝》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2003 04 24 Revised Para 3.0 inserted; Para 3.9, 3.10, 3.11, 3.12, 3.13, 4 deleted 1991 01 31 DE00E 00107002086 Revised 3.5 std para added J. Huebner 1963 08 16 CTS4-58846-1 Released Printed copies are uncont

2、rolled Page 1 of 2 Copyright 2003, Ford Global Technologies, Inc. COPPER WIRE, BATTERY CABLE - #6 GAGE ESF-M1L34-A 1. SCOPE The material defined by this specification is a #6 gage stranded, insulated battery cable. 2. APPLICATION This specification was released originally for material used as a batt

3、ery cable on automotive passenger vehicles. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 CABLE SIZE The finished cable diameter shall not exce

4、ed SAE limits for type SGR cable. 3.2 INSULATION COLOR Black, unless otherwise specified on the engineering drawing 3.3 CABLE QUALITY Shall meet all of the requirements listed herein and must be equal to the original approved sample. 3.4 WIRE QUALITY Shall consist of bare ESF-M2L1-A, soft or anneale

5、d round copper wire, prior to bunching or stranding. 3.5 CABLE CONSTRUCTION Shall consist of a minimum of 48 strands (any manufacturing tolerance must be additive) of #23 gage bare copper wire having a minimum area of 11.85 mm2. The strands shall be bunched and laterally served with a 25.4 x 0.08 mm

6、 minimum paper or polyester film tape. The tape must have a 12 1/2% minimum overlap. ENGINEERING MATERIAL SPECIFICATION ESF-M1L34-A Page 2 of 2 Copyright 2003, Ford Global Technologies, Inc. 3.6 INSULATION QUALITY The finished cable shall be covered with a good grade of elastomer which meets SAE typ

7、e SGR requirements. The insulation must have a 1.19 mm wall nominal thickness. 3.7 RESISTIVITY, FINISHED CABLE, max 1453 microohms/m at 20 C 3.8 PHYSICAL AND ELECTRICAL PROPERTIES Three samples of cable are required. One for each of the high temperature, low temperature and oil absorption tests. All

8、 samples are subjected to the dielectric breakdown test at the completion of their respective tests. These samples are 0.6 m in length with 25 mm of insulation stripped from both ends. 3.8.1 High Temperature Resistance No fracture or splitting of the insulation Test Method: Suspend sample over a 254

9、 mm mandrel with a 2.72 kg weight at each end. Soak at 121 +/- 2 C for 120 h in a circulating air oven. Cool to 23 +/- 2 C, remove the weight and bend the sample around the mandrel in a reverse direction at a rate not exceeding 1 turn per minute until a 180 bend is completed. 3.8.2 Low Temperature R

10、esistance No fracture or splitting of the insulation Test Method: Reduce temperature of a straight piece of sample to - 34 C at a rate not to exceed 68 C per minute. Hold for 3 h and then wrap around a 254 mm mandrel for 180 at a rate of 1 turn per 10 s. 3.8.3 Oil Absorption Resistance Cable dia sha

11、ll not increase more than 15% nor shall the insulation fracture or split Test Method: Immerse sample to within 38 mm from the end into a solution of 50 % kerosene and 50 % SAE 10W engine oil for 20 h at 49 +/- 2 C. Wrap sample around a 254 mm mandrel for 180 . 3.8.4 Dielectric Resistance No rupture of the insulation Test Method: Join exposed ends of sample and immerse loop to within 150 mm of ends in a 5 % salt bath (salt content by weight at 27 C). Soak 5 h and then apply 500 V (RMS) 60 cps (Hz) between sample conductor and salt bath for 1 minute.