EN 15719-2015 en Sanitary appliances - Baths made from impact modified coextruded ABS acrylic sheets - Requirements and test methods《卫生器具 冲击改性复合ABS 亚克力板材制成的浴室 要求和试验方法》.pdf

《EN 15719-2015 en Sanitary appliances - Baths made from impact modified coextruded ABS acrylic sheets - Requirements and test methods《卫生器具 冲击改性复合ABS 亚克力板材制成的浴室 要求和试验方法》.pdf》由会员分享，可在线阅读，更多相关《EN 15719-2015 en Sanitary appliances - Baths made from impact modified coextruded ABS acrylic sheets - Requirements and test methods《卫生器具 冲击改性复合ABS 亚克力板材制成的浴室 要求和试验方法》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 15719:2015Sanitary appliances Bathsmade from impact modifiedcoextruded ABS/acrylic sheets Requirements and testmethodsBS EN 15719:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 15719:2015.It supersedes BS EN 15719:2009 which

2、is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/503, Sanitary appliances.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract.

3、 Users are responsible for its correctapplication. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 85599 3ICS 91.140.70Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority

4、of theStandards Policy and Strategy Committee on 30 November 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 15719:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15719 November 2015 ICS 91.140.70 Supersedes EN 15719:2009English Version Sanitary applianc

5、es - Baths made from impact modified coextruded ABS/acrylic sheets - Requirements and test methods Appareils sanitaires - Baignoires en feuilles coextrudes ABS/acrylique modifi choc - Prescriptions et mthodes dessai Sanitrausstattungsgegenstnde - Badewannen, hergestellt aus schlagzh-modifizierten co

6、extrudierten ABS/Acrylplatten - Anforderungen und PrfverfahrenThis European Standard was approved by CEN on 20 September 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard

7、without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any ot

8、her language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic

9、, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COM

10、MITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15719:2015 EBS EN 15719:

11、2015EN 15719:2015 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Requirements . 5 4.1 General 5 4.2 Material . 5 4.3 Surface appearance 5 4.4 Waste outlet hole . 5 4.5 Overflow hole . 6 4.6 Hole edges 6 4.7 Bath-mounted tapware . 6 4.8 Hand

12、grips . 6 4.9 Dimensional deviations 6 4.10 Geometric deviations . 6 4.10.1 General 6 4.10.2 Squaring 6 4.10.3 Straightness of the rim sides . 6 4.10.4 Straightness of the bottom edge of the rim 6 4.10.5 Flatness of the top surface of the rim . 7 4.11 Bottom of the bath 7 4.12 Resistance to temperat

13、ure changes . 7 4.13 Resistance to impact 7 4.14 Permitted deflections 7 4.15 Bath rims 7 4.16 Surface mechanical resistance . 8 4.17 Chemical and stain resistance 8 5 Marking . 8 Annex A (normative) Bath test methods 9 A.1 Sequence of tests . 9 A.2 Geometric deviations . 9 A.2.1 Test apparatus 9 A.

14、2.2 Squaring 9 A.2.3 Straightness of the rim side 10 A.2.4 Straightness of the bottom edge of the rim . 11 A.2.5 Flatness of the top surface of the rim 12 A.3 Resistance to temperature change 13 A.3.1 Test apparatus. 13 A.3.2 Procedure 13 A.4 Resistance to impact . 14 BS EN 15719:2015EN 15719:2015 (

15、E) 3 A.4.1 Test apparatus . 14 A.4.2 Test procedure 14 A.5 Determination of deflections 15 A.5.1 General . 15 A.5.2 Test apparatus . 15 A.5.3 Installation methods . 16 A.5.4 Preloading . 18 A.5.5 Deflection test 1 Deflection of the rim and the bottom due to a load on the bottom 18 A.5.6 Deflection t

16、est 2 Deflection of the bottom and rim due to a load on the bottom . 20 A.5.7 Deflection test 3 Deflection of the rim due to a load on the long side of the rim 21 A.5.8 Deflection test 4 Deflection of the rim due to a load on the end of the bath 22 A.6 Handgrip tests 24 A.6.1 General . 24 A.6.2 Test

17、 apparatus . 24 A.6.3 Procedure 24 A.7 Resistance to scratching . 24 A.7.1 Test apparatus . 24 A.7.2 Test specimen 25 A.7.3 Procedure 25 Bibliography . 27 BS EN 15719:2015EN 15719:2015 (E) 4 European foreword This document (EN 15719:2015) has been prepared by Technical Committee CEN/TC 163 “Sanitary

18、 appliances”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be withdrawn at the latest by May 2016. At

19、tention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 15719:2009. The only change from the previous edition is in

20、A.7.3 where “50 %” has been changed to “25 %”. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, For

21、mer Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 15719:2015EN 15719:2015 (E) 5 1 Sc

22、ope This European Standard specifies requirements for baths for domestic purposes made from impact modified coextruded ABS/acrylic sheets conforming to EN 13559 with the aim of ensuring that the product, when installed in accordance with the manufacturers instructions, will provide satisfactory perf

23、ormance in use. This European Standard is applicable to all sizes and shapes of baths. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For

24、 undated references, the latest edition of the referenced document (including any amendments) applies. EN 232, Baths Connecting dimensions EN 13559:2003, Specifications for impact modified coextruded ABS/Acrylic sheets for baths and shower trays for domestic purposes ISO 4586-2:2004, High-pressure d

25、ecorative laminates Sheets made from thermosetting resins Part 2: Determination of properties 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 domestic purposes use in homes, hotels, accommodation for students, hospitals and similar buildings,

26、 except when special medical provisions are required 4 Requirements 4.1 General The manufacturer shall provide instructions for installation and care with each bath. The bath shall be free from sharp edges that would be exposed after the installation of the bath in accordance with the manufacturers

27、instructions. 4.2 Material The bath shall be manufactured from impact modified coextruded ABS/acrylic sheet material complying with EN 13559. 4.3 Surface appearance When the bath is visually inspected under strong and oblique illumination there shall be no evidence of cracks, chips, or other surface

28、 defects, such as unexpected changes in colours, etc. that will impair the appearance or performance of the bath. 4.4 Waste outlet hole The bath shall have at least one outlet hole. The dimensions of the waste outlet hole and the clearance around the waste outlet hole shall either be in accordance w

29、ith the requirements of EN 232 or the manufacturer shall supply or recommend a suitable waste outlet fitting. BS EN 15719:2015EN 15719:2015 (E) 6 4.5 Overflow hole When the bath is provided with an overflow hole the dimensions of the overflow hole and the clearance around the overflow hole shall eit

30、her be in accordance with the requirements of EN 232 or the manufacturer shall supply or recommend a suitable overflow fitting. 4.6 Hole edges The edges of any holes in the bath shall not show evidence of chips, cracks, or any other defects that may impair the appearance or performance of the bath.

31、4.7 Bath-mounted tapware When the bath is intended to accommodate bath-mounted tapware the space and area provided shall either comply with the requirements of EN 232 or the manufacturer shall supply or recommend a suitable tapware. 4.8 Handgrips When a handgrip(s) is fitted it shall be tested in ac

32、cordance with A.6 and the bath and the handgrip shall be free from any permanent deformation or other defects that will impair the functioning and/or the appearance of the bath. If not pre-fitted by the manufacturer, the manufacturers instructions shall indicate how and where the handgrips are fitte

33、d. 4.9 Dimensional deviations The dimensions of baths shall not deviate from the size quoted by the manufacturer by greater than 5 mm. If the manufacturer states two sizes (e.g. both a work size and a nominal size) he shall state to which size the permitted deviations apply. For round baths, length

34、and width correspond to the diameter. 4.10 Geometric deviations 4.10.1 General The straight sides or edges of the bath that might abut independent surroundings or supporting structures shall comply with the requirements of 4.10.2 to 4.10.4 and all baths shall comply with 4.10.5. These requirements a

35、re not applicable to sides or edges that are purposely designed as curves or slopes. 4.10.2 Squaring When tested in accordance with A.2.2 the deviation from square, q, shall be less than or equal to 5 mm. 4.10.3 Straightness of the rim sides When tested in accordance with A.2.3 the deviation from st

36、raightness of the rim sides, s, shall be less than or equal to 5 mm. 4.10.4 Straightness of the bottom edge of the rim When tested in accordance with A.2.4 the deviation from straightness of the bottom edge of the rim, r, shall be less than or equal to 5 mm. BS EN 15719:2015EN 15719:2015 (E) 7 4.10.

37、5 Flatness of the top surface of the rim When tested in accordance with A.2.5 the deviation from flatness of the top surface of the rim, c, shall be less than or equal to 5 mm. 4.11 Bottom of the bath When the bath is installed in accordance with the manufacturers instructions and the waste outlet h

38、ole is open, all water shall empty from the bath unless prevented by surface tension. 4.12 Resistance to temperature changes When tested in accordance with A.3 baths shall show no evidence of distortion or other defects that impair the appearance or functioning of the bath and any deflection shall b

39、e less than or equal to 4 mm. 4.13 Resistance to impact When tested in accordance with A.4 the bottom and the rim of the bath shall show no evidence of distortion or other defects that impair the appearance or functioning of the bath. 4.14 Permitted deflections When tested in accordance with A.5 the

40、 deflections shall be less than or equal to the values given in Table 1. Table 1 Permitted deflections Test method Maximum deflections aunder load and permitted residual deflections for installation methods bmm a) b) c) d) e) A.5.5 1 on the four free rims 2 on the bottom 1 on the three free rims 0,5

41、 on the fixed rim 2 on the bottom 1 on the two free rims 0,5 on the two fixed rims 2 on the bottom 1 on the free rim 0,5 on the three fixed rims 2 on the bottom 0,5 on all rims 2 on the bottom A.5.6 2 on the four free rims 3 on the bottom 2 on the three free rims 0,5 on the fixed rim 3 on the bottom

42、 2 on the two free rims 0,5 on the two fixed rims 3 on the bottom 2 on the free rim 0,5 on the three fixed rims 3 on the bottom 0,5 on all rims 3 on the bottom A.5.7 4 on the rim 0,3 residual 4 on the rim 0,3 residual 4 on the rim 0,3 residual 4 on the rim 0,3 residual Not applicable A.5.8 4 on the

43、rim 0,3 residual 4 on the rim 0,3 residual 4 on the rim 0,3 residual Not applicable Not applicable aValues in addition to any deflection of the test rig (see A.5.2). bSee A.5.3. 4.15 Bath rims When a bath incorporating a nominally flat top surface of the rim is installed in accordance with the manuf

44、acturers instructions, the rim shall not encourage water to drain away from the inside of the BS EN 15719:2015EN 15719:2015 (E) 8 bath. Roll top rims and rims incorporating special features, e.g. headrests, are not subject to this requirement. 4.16 Surface mechanical resistance When tested in accord

45、ance with A.7, any scratch shall not exceeded 0,1 mm or the total thickness of the top layer whichever is the least. 4.17 Chemical and stain resistance When tested in accordance with EN 13559:2003, 5.4, baths shall show no permanent staining or deterioration. 5 Marking Baths shall be legibly marked

46、with the following information: a) reference to this European Standard (EN 15719); b) the name or trademark of the manufacturer or supplier. BS EN 15719:2015EN 15719:2015 (E) 9 Annex A (normative) Bath test methods A.1 Sequence of tests The tests shall be carried out on one bath of each type in the

47、sequence A.2, A.3, A.5, A.4, A.6, A.7. A.2 Geometric deviations A.2.1 Test apparatus a) length measuring device with an accuracy of 0,5 mm; b) reference plane surface with flatness tolerance of 0,5 mm; c) fixed square: fixed to the reference plane surface, at least 25 mm deeper than the depth of the

48、 rim side to be measured, one arm at least 300 mm longer than the length to be measured and the other arm at least as long as the width to be measured; d) movable square: at least 25 mm deeper than the depth of the rim side to be measured, one side at least 300 mm long and the other side at least as

49、 long as the width to be measured; e) thickness comparator or gauge with an accuracy of 0,1 mm; f) spacing rollers made of metallic materials: at least 25 mm deeper than the depth of the rim side to be measured and with a diameter Dsrwith a tolerance of 0,25 mm; g) thickness wedge with a thickness of 500,1-mm. A.2.2 Squaring Place the bath upside down on the reference plane surface as shown in Figure A.4, compensating for any design features, e.g. headrests. Posit