EN 15380-3-2006 en Railway applications - Designation system for railway vehicles - Part 3 Designation of installation sites and locations《轨道交通 铁路车辆的命名和符号系统 第3部分 安装地点和位置的命名》.pdf

《EN 15380-3-2006 en Railway applications - Designation system for railway vehicles - Part 3 Designation of installation sites and locations《轨道交通 铁路车辆的命名和符号系统 第3部分 安装地点和位置的命名》.pdf》由会员分享，可在线阅读，更多相关《EN 15380-3-2006 en Railway applications - Designation system for railway vehicles - Part 3 Designation of installation sites and locations《轨道交通 铁路车辆的命名和符号系统 第3部分 安装地点和位置的命名》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN15380-3:2006Railway applications Designation system for railway vehicles Part 3: Designation of installation sites and locationsThe European Standard EN 15380-3:2006 has the status of a British StandardICS 01 110; 45.060.01g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g3

2、7g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 15380-3:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2006 BSI 2006ISBN 0 580

3、48946 9National forewordThis British Standard is the official English language version of EN 15380-3:2006. The UK participation in its preparation was entrusted to Technical Committee RAE/1, Railway applications, which has the responsibility to: A list of organizations represented on this committee

4、can be obtained on request to its secretary.This standard has been produced from Part 4 of the DIN 25002 series of standards under the CEN fast-track procedure. The UK voted against the document in both associated ballots stating that the translation of the documents from German to prepare the Engli

5、sh version has resulted in a lack of clarity as to the intent and meaning of some of the terminology used. There is a concern that some of the railway-related terminology used does not correspond to UK usage. Therefore, this standard should be applied with care and consideration in order to avoid mi

6、sunderstanding.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electroni

7、c Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to unders

8、tand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a fro

9、nt cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE

10、 NORMEN 15380-3April 2006ICS 01.110; 45.060.01English VersionRailway applications - Designation system for railway vehicles -Part 3: Designation of installation sites and locationsApplications ferroviaires - Systme de classification pourvhicules ferroviaires - Partie 3: Description des positionsdins

11、tallationBahnanwendungen - Kennzeichnungssystematik frSchienenfahrzeuge - Teil 3: Kennzeichnung vonAufstellungs- und EinbauortenThis European Standard was approved by CEN on 6 March 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for givi

12、ng this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions

13、 (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus,

14、 Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUR

15、OPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15380-3:2006: EEN 15380-3:2006 (E) 2 Contents Page Foreword3 Introduction

16、.4 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Designation of installation sites.4 4.1 General4 4.2 Designation set 5 5 Designation of locations .6 5.1 General6 5.2 Designation set 6 Annex A (informative) Examples of installation site and location designation9 Bibliography 12 Lis

17、t of Tables Table 1 Location subdivision. 8 List of Figures Figure 1 Designation principle. 5 Figure 2 Example of installation site vehicle designation 5 Figure 3 Location designation principle. 6 Figure 4 Example of a location designation. 7 Figure 5 Example of a location designation with product g

18、roup and location given 7 Figure A.1 Examples of installation site and location designation . 9 Figure A.2 Designation of locations on a locomotive . 10 Figure A.3 Designation of locations on a 3-compartment suburban vehicle . 11 EN 15380-3:2006 (E) 3 Foreword This document (EN 15380-3:2006) has bee

19、n prepared by Technical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2006, and conflicting national

20、 standards shall be withdrawn at the latest by October 2006. The EN 15380 series of standards, Railway applications Designation system for railway vehicles consists of: Part 1: General principles Part 2: Product groups Part 3: Designation of installation sites and locations This European Standard is

21、 based on Part 4 of the DIN 25002 series of standards. After approval, the text of DIN 25002-4 submitted to the PQ procedure was brought into line with the formal requirements of an EN. The resulting editorial amendments have led to slightly modified wordings but they have no effect on the technical

22、 content of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

23、 Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 15380-3:2006 (E) 4 Introduction Giving the location designations is necessary in order to systematize installation planning

24、 and to provide traceability of vehicle parts, structural units, combined assemblies and objects. 1 Scope As a railway-specific technical standard, this document gives rules for the designation of installation sites and locations in railway vehicles. 2 Normative references The following referenced d

25、ocuments are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 15380-1:2006, Railway aplications Designation system for railwa

26、y vehicles Part 1: General principles EN 15380-2, Railway aplications Designation system for railway vehicles Part 2: Product groups 3 Terms and definitions For the purposes of this document, the terms given in EN 15380-1:2006 apply. 4 Designation of installation sites 4.1 General This designation g

27、ives information concerning the position of a unit, a vehicle or an assembly in a fixed train configuration. EN 15380-3:2006 (E) 5 4.2 Designation set Figure 1 shows the layout of the designation set. It consists of the prefix signs ”+” followed by three code letters and two code numbers for the pos

28、ition inside a fixed train configuration. Key 1 Installation site prefix sign 2 Designation of railway vehicles 3 Designation of train (vehicle fleet) 4 Designation of vehicle type 5 Position within the train (only required if identical vehicles exist within a train) Figure 1 Designation principle E

29、xamples of the data positions A1, A2 and A3 are given in Annex A of EN 15380-1:2006. Figure 2 shows an example of a designation of one of several identical vehicles in a train configuration as indicated in Figure A.1. Key 1 Installation site prefix sign 2 “Rolling Stock“ vehicle fleet 3 High-speed t

30、rain 4 Centre car (vehicle type) 5 Vehicle No.02 in the train Figure 2 Example of installation site vehicle designation EN 15380-3:2006 (E) 6 Annex A gives examples of the numbering system of installation sites and locations. 5 Designation of locations 5.1 General This designation gives information

31、concerning the location of structural units, combined assemblies and objects in vehicles, structural units and assemblies. 5.2 Designation set Figure 3 shows the layout of the designation set. It consists of the prefix sign “+“ followed by two code letters for the product group, two code numbers (lo

32、cation), a classification mark and a further possibility for designating the location. It is not required in every case to indicate the product group. Examples are shown in Figures 4 and 5. Key 1 Location prefix sign 2 Product group plan according to EN 15380-2 3 Subdivision of the locations in a ve

33、hicle (see Table 1) 4 Designation of the locations in combined assemblies, structural units and objects (areas and/or co-ordinates) not specified Figure 3 Location designation principle Figure 4 shows an example of the minimum entry for a location designation EN 15380-3:2006 (E) 7 Key 1 Location pre

34、fix sign 2 Pantograph 3 Location on the roof (see Table 1) 4 Location Figure 4 Example of a location designation Figure 5 shows an example of a complete location designation. Key 1 Location prefix sign 2 Runnig gear from EN 15380-2 3 Underframe location (see Table 1) 4 Location in running gear (W1L

35、= wheelset shaft 1 left-hand side) Figure 5 Example of a location designation with product group and location given The corresponding numbers for designating the locations are specified in Table 1. The figures in the Annex are intended to clarify matters for different railway vehicles. EN 15380-3:20

36、06 (E) 8 Table 1 Location subdivision Main group Subdivision Name of the location 00 Roof, outside 01 to 09 Roof, outside; subdivision according to the situation 10 Drivers cab 11 Drivers desk 12 Cubicle in the drivers cab, left-hand side 13 Cubicle in the drivers cab, right-hand side 10 14 Drivers

37、cab, rear wall, left-hand side 15 Drivers cab, rear wall, right-hand side 16 Drivers cab, floor 17 Drivers cab, ceiling 18 Vehicle head, left-hand side 19 Vehicle head, right-hand side 20 Side wall, right-hand side (with cove) 21 to 29 Subdivision according to the situation (e.g. windows) 30 Side wa

38、ll, left-hand side (with cove) 31 to 39 Subdivision according to the situation 40 Interior, right-hand side 41 to 49 Subdivision according to the situation 50 Interior, left-hand side 51 to 59 Subdivision according to the situation 60 Interior ceiling 61 to 69 Subdivision according to the situation,

39、 e.g. intermediate ceiling in double-decker coaches 70 Underframe (framework of a locomotive) 71 to 79 Subdivision according to the situation 80 End wall, rear wall, intercommunication gangway, drivers cab 2 of single-unit vehicles (e.g. in locomotives) 81 to 89 Subdivision according to the situatio

40、n 90 Reserved EN 15380-3:2006 (E) 9 Annex A (informative) Examples of installation site and location designation Figure A.1 shows the designation of the installation site and location in various trains. The direction of travel of the vehicles is shown in acordance with EN 13775-1. Key 1 Locomotive,

41、2 drivers cabs 2 Traction unit head, 1 drivers cab 3 Traction unit, 2 drivers cabs 4 Traction unit, 4-compartment 5 Suburban train, underground train 6 High-speed train (ICT) Direction of counting Figure A.1 Examples of installation site and location designation Other examples of installation site a

42、nd location designation are given in Figures A.2 and A.3. EN 15380-3:2006 (E) 10 Figure A.2 Designation of locations on a locomotive EN 15380-3:2006 (E) 11 Figure A.3 Designation of locations on a 3-compartment suburban vehicle EN 15380-3:2006 (E) 12 Bibliography 1 EN 13775-1, Railway aplications Me

43、asuring of new and modified freight wagons - Part 1: Measuring principles blankBS EN 15380-3:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and

44、at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and se

45、rvices. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers m

46、embers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0

47、)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on

48、 standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Inform

49、ation Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Onli