EN 929-1993 en Inland Navigation Vessels - Push-Tows - Mounting Attachment for Demountable Signal Masts《内河航行船舶 推拖船 可卸信号桅杆用安装附件》.pdf

《EN 929-1993 en Inland Navigation Vessels - Push-Tows - Mounting Attachment for Demountable Signal Masts《内河航行船舶 推拖船 可卸信号桅杆用安装附件》.pdf》由会员分享，可在线阅读，更多相关《EN 929-1993 en Inland Navigation Vessels - Push-Tows - Mounting Attachment for Demountable Signal Masts《内河航行船舶 推拖船 可卸信号桅杆用安装附件》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、CEN EN8929 93 3404589 0072009 284 = BRITISH STANDARD - Inland navigation vessels - Mounting attachment for demountable signal masts Push-tows - The European Standard EN 929 : 1993 has the status of a British Standard UDC 629.122.018.3 : 656.62 . 654.91 BS EN 929 : 1995 _ CEN EN*929 93 9 3404589 0072

2、OLO TTb W Amd. No. Date BS EN 929 : 1995 Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee GME/32, Steering committee on shipbuilding and marine standards, upon which the following bodies were represented: Bri

3、tish Marine Equipment Council British Maritime Rchnology British Motor Ship Owners Association British Waterways Board Chamber of Shipping Department of Transport (Marine Directorate) Lloyds Register of Shipping Ministry of Defence Shipbuilders and Shiprepairers Association This British Standard, ha

4、ving been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 April 1995 O BSI 1995 The following BSI references relate to the work on this standard: Committee reference GME/32 Draft for comment 93/702647

5、DC ISBN O 580 23237 9 CEN ENx929 93 m 3404L89 0092011 932 = BS EN 929 : 1995 National foreword This British Standard has been prepared by Technical Committee GME/32 and is the English language version of EN 929 : 1993 Inland navigution vessels -Push-tows - Mounting attachment for hountuble signal ma

6、sts, published by the European Committee for Standardization (CEN). EN 929 was produced as a result of international discussions in which the United Kingdom took an active part. Compliance with a British Standard does not of itself confer immunity from legal obligations. i CEN ENS929 93 = 3404589 00

7、92032 879 W EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 929 November 1993 UDC 629.122.018.3 : 656.62 : 654.91 Descriptors: Inland navigation, ships, signal masts, line, fittings, equipment, specifications, dimensions, manufacturing, layout, designation, maritime safety English version Inlan

8、d navigation vessels - Push-tows - Mounting attachment for demountable signal masts Bateaux de navigation intrieure - Convois pousss - Ferrures dattache pour mts de signalisation amovibles losnehmbare Signalmaste Fahrzeuge der Binnenschiffahrt - Schubverbnde - Masthalterung fr This European Standard

9、 was approved by CEN on 1993-11-15. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nati

10、onal standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and no

11、tified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United King

12、dom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: lue de Stassart 36, B-1050 Brussels O 1993 Copyright reserved to CEN members Ref. No. EN 929 : 1993 E CEN EN*929 93 3404589 0092033 705 - Page 2 EN 929 : 1993 Foreword T

13、his European Standard has been drawn up by CEN/TC 15, Inland navigation vessels, whose secretariat is held by the German Institute for Standardization (DIN). It was required in order to facilitate the exchange of push barges in inland navigation and minimize the dangers to crew and shipping. The sta

14、ndard is based on IS0 7236 and national standards. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1994, and conflicting national standards shall be withdrawn at the latest by May 1994. In acc

15、ordance with the CENKENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Con

16、tents Foreword Introduction 1 2 3 4 4.1 4.2 4.3 4.4 4.5 4.6 5 6 7 Scope Normative references Definitions Technical requirements Dimensions Mast stand Mast clamp Mounting attachment Mounting attachment arrangement on the push barge Mast Material Testing Designation m3e 2 3 3 3 3 3 3 3 3 4 Annex A (no

17、rmative) Mast lower part CEN EN*929 93 34045B OOZOLY bY1 = Introduction Since push barges do not generally have their own masts fitted with the lights required for push-tows, the masts are carried on the push vessel and fitted to the barges when the vessels are connected. Therefore, the mounting att

18、achments should be of a uniform type, have the same dimensions and fit the lower part of the mast so that work may be carried out quickly, easily and safely even in bad visibility conditions and in each weather situation. In addition, the mounting attachments ensure that the masts, and therefore the

19、 push-tow light, are correctly seated which is of fundamental importance for safety in shipping traffic. 1 Scope This standard applies to mounting attachments for demountable masts with an integral mast lower part for the placing of light on push barges. It specifies construction, dimensions, manufa

20、cture, arrangement and means of attachment. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated re

21、ferences, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. IS0 2768-1 General tolerances - lerances for linear an

22、d angular dimensions without individual tolerance indications Inland navigation vessels - Demountable signal masts for push-tows - Mounting attachment Hot-rolled products of non-alloy structural steels - Technical IS0 7236 EN 10025 Page 3 EN 929 : 1993 3 Definitions For the purposes of this European

23、 Standard, the following definitions apply: 3.1 Mounting attachent A device comprising a mast stand and mast clamp which are arranged on the barge in such a way that they can maintain a signal mast in the specified position. 3.2 Mast stand A device fixed to the deck which accepts the lower part of t

24、he signal mast and secures it against rotation about the vertical mast axis. 3.3 Mast clamp A device which secures the top of the lower portion of the signal mast. 3.4 Mast lower part The lower part of the signal mast which is inserted into the mounting attachment. 4 Technical requirements Dimension

25、s in millimetres. General tolerances: IS0 2768-c. The requirements relate to construction, dimensions, design, arrangement and means of attachment. 4.1 Dimensions The mounting attachment is not expected to conform to the design illustrated here; compliance is only required in the case of the dimensi

26、ons specified. 4.2 Mast stand Smooth edges 4.3 Mast clamp The clamp is shown to be attached using screws and nuts/wing nuts. Any equivalent means of attachment is permitted provided that the mast is held securely. Only captive screws, nuts or wing nuts shall be delivery conditions used. CEN EN*727 9

27、3 m 3404589 0072015 588 = fige 4 EN 929: 1993 4.4 Mounting attachment The mounting attachment consists of the mast stand and a mast clamp. The mast stand shall be positioned so that the signal mast bearing pins are precisely aligned parallel to the longitudinal and transverse axes of the vessel. In

28、addition, the mast stand and mast clamp shall be arranged in such a way that the axis of the lower part of the signal mast is perpendicular to the design waterline plane. The arrangement illustrated in figure 3 is an example of this. 4.5 Mounting attachment arrangement on the push barge The mounting

29、 attachments shall be arranged on the push barge as shown in figure 4. The mounting attachments fitted to the vessel sides shall be arranged so that the masts may be mounted parallel to the longitudinal vertical plane of the vessel. For safety reasons, they shall not be positioned within the clear w

30、idth of the walkway and shall be arranged to ensure an easy mounting of the mast. The attachments fitted in the centre of the vessel may be rotated by 90 (e.g. in restricted conditions) so that the masts may be mounted parallel to the transverse vertical plane of the vessel. 4.6 Mast Only the dimens

31、ions of the lower end of the mast (mast lower part) are specified in annex A. The upper part of the mast, its height, the navigation light arrangement and other characteristics are not covered by this standard. They are governed by the shipping regulations of the corresponding navigation zone. 5 Mat

32、erial Weldable steel as specified in EN 10025. The screws, nuts or bolts used for the clamp shall be made of stainless steel or other non-corrodible materials. 6 Testing For the purposes of this standard, test the technical requirements as specified in this standard by visual examination and measure

33、ment. 7 Designation A mounting attachment for demountable signal masts comprising mast stand (figure 1) and mast clamp (figure 2) shall have the following designation: Mounting attachment EN 929 CEN EN*929 93 = 3404589 0092036 414 Page 5 EN 929 : 1993 l- cc- 281, 160 b Figure 1. Mast stand p 1 View

34、sliowri witliniit screws or iiiits Welded1 L 50 x 50 x 5 - I I I I Wingnut M12 / Screw M12 x 40 M12 x 50 with 2 nuts welded on Figure 2. Mast clamp CEN ENs929 93 m 3404589 00920L7 350 Page 6 EN 929 : 1993 Mast clamp 1 !IlII II I shown without screws or nuts Welded Figure 3. Mounting attachment Mast

35、stand bearing plate U CEN EN*929 93 D 3404589 0092018 297 Page 7 EN929: 1993 a I 1000 Mounting attachment i La,i li I Figure 4. Mounting attachment arrangement on the push barge CEN ENs929 93 3404589 O092039 323 Page 8 EN 929: 1993 Annex A (normative) Mast lower part E 8 2 1 30 *. rn (u 19 -or + I I

36、II I II I I 1304 Dimensions in miiimetres General tolerances: IS0 2768- C Figure A. 1 Mast lower part BS EN 929 : 1995 BSI 389 Chiswick High Road London W4 4AL 9504 - 6 - 0.5k - FP CEN EN*929 93 3404587 O092020 945 = BSI - British Standards Institution BSI is the independent national body responsibl

37、e for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are respo

38、nsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. Any person who finds an inaccuracy or ambiguity while using this British Standard should bring it t

39、o the attention of the Quality Manager, BSI without delay so that the matter may be investigated swiftly. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, internat

40、ional and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick: Tel: 0181 996 7000; Fax: O181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British S

41、tandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Database, the BSI Information Technology Service (BITS) and its Technical Help to Exporters Service. Contact

42、 the Information Department at Chiswick: TA: 0181 996 7111; Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membersh

43、ip at Chiswick: Tel: O181 996 7002; Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications and no part may be reproduced in any form without the prior permission in writing of BSI. This does not preclude the free use, in the course of implementing the standard of necessary details

44、such as symbols and size, type or grade designations including use by incorporation into computer programs, but where these details are reproduced including without limitation in printed form, in computer programs or in any other form whatsoever, the permission in writing of BSI must be obtained and if granted will be on terms including royalty, before the product is sold, Licensed or otherwise exploited for commercial gain. Enquiries about copyright should be made to the Copyright Manager at Chiswick. SBN O 580 23237 9 GMEl32