EN 12561-6-2011 en Railway applications - Tank wagons - Part 6 Manholes《铁路应用 坦克车 第6部分 检查孔》.pdf

《EN 12561-6-2011 en Railway applications - Tank wagons - Part 6 Manholes《铁路应用 坦克车 第6部分 检查孔》.pdf》由会员分享，可在线阅读，更多相关《EN 12561-6-2011 en Railway applications - Tank wagons - Part 6 Manholes《铁路应用 坦克车 第6部分 检查孔》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12561-6:2011Railway applications TankwagonsPart 6: ManholesBS EN 12561-6:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12561-6:

2、2011.It supersedes BS EN 12561-6:2002 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee RAE/1/-/9, Railway Applications - Wagons (Tank/Freight).A list of organizations represented on this committee can beobtained on request to its secretary.This publicati

3、on does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 72812 9ICS 13.300; 45.060.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the

4、 authority of theStandards Policy and Strategy Committee on 31 July 2011.Amendments issued since publicationDate Text affectedBS EN 12561-6:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12561-6 June 2011 ICS 13.300; 45.060.20 Supersedes EN 12561-6:2002English Version Railway applications

5、- Tank wagons - Part 6: Manholes Applications ferroviaires - Wagons citernes - Partie 6: Trous dhomme Bahnanwendungen - Kesselwagen - Teil 6: Mannloch This European Standard was approved by CEN on 3 June 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate

6、the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standa

7、rd exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the natio

8、nal standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerl

9、and and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN

10、12561-6:2011: EBS EN 12561-6:2011EN 12561-6:2011 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Requirements .54.1 Threaded fasteners 54.2 Dimensions .55 End fitted manhole for gas tank wagons 55.1 Position of manhole.55.2 Ring and plate 65.2.1 General 65.

11、2.2 Dimensions .65.2.3 Surface parameters .75.2.4 Tolerances 75.3 Gaskets .76 Top fitted manhole for gas tank wagons .87 Bolted manhole for liquid substances . 118 Swing bolt manholes for liquid substances 118.1 General . 118.2 General arrangement 118.3 Swing bolts 128.4 Wing nuts . 138.5 Swing bolt

12、 hinge pin . 148.6 Gasket 14Bibliography . 15Figures Figure 1 Positioning of manhole 6Figure 2 Dimensions of ring and plate .7Figure 3 Gasket dimensions .8Figure 4 Arrangement of valves on manlid .9Figure 5 Dimensions of internal valve flange . 10Figure 6 Dimensions of recess in the manlid for inter

13、nal valve flange . 10Figure 7 Manlid handle - minimum dimensions . 11Figure 8 Main dimensions for swing bolt manholes . 12Figure 9 Swing bolt . 13Figure 10 Wing nut 13Figure 11 Gasket dimensions 14BS EN 12561-6:2011EN 12561-6:2011 (E) 3 Foreword This document (EN 12561-6:2011) has been prepared by T

14、echnical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2011, and conflicting national standards sha

15、ll be withdrawn at the latest by December 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12561-6:20

16、02. This European Standard Railway applications Tank wagons consists of the following parts: Part 1: Identification plates for tank wagons for the carriage of dangerous goods; Part 2: Bottom emptying devices for liquid products including vapour return; Part 3: Bottom filling and emptying devices for

17、 gases liquefied under pressure; Part 4: Devices for top filling and emptying of liquid products; Part 5: Devices for vapour return while filling or emptying of liquid products; Part 6: Manholes; Part 7: Platforms and ladders; Part 8: Heating connections. The changes made during this revision are ed

18、itorial because of the change of the title of part 1 and the necessary updates of references. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,

19、 Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 12561-6:2011EN 12561-6:2011 (E) 4

20、1 Scope This European Standard applies to manholes on tank wagons used for the transport of dangerous substances. Safety functions of these devices are subject to RID requirements and not described in this document. This European Standard specifies the dimensions for the interchangeability of seals

21、and other wearing parts and defines also the important dimensions for: manholes for gas tank wagons located in one end of the tank; manholes for gas tank wagons located on the top of the tank including the arrangement of fittings; bolted manholes for tank wagons for liquid substances located on the

22、top of the tank; swing bolt manholes for tank wagons for liquid substances located on the top of the tank. Quick closing/opening manholes are permitted but are not covered by this European Standard. This European Standard applies to new tank wagons built after the 1st January 2010. 2 Normative refer

23、ences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 14025, Tanks for the transport of danger

24、ous goods Metallic pressure tanks Design and Construction EN 14564, Tanks for transport of dangerous goods Terminology EN 20898-2, Mechanical properties of fasteners Part 2: Nuts with specified proof load values Coarse thread (ISO 898-2:1992) EN ISO 286-1, Geometrical product specifications (GPS) IS

25、O code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits (ISO 286-1:2010) EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread (IS

26、O 898-1:2009) EN ISO 4287, Geometrical product specification (GPS) Surface texture: Profile method Terms, definitions and surface texture parameters (ISO 4287:1997) ISO 7005-1:1992, Metallic flanges Part 1: Steel flanges ISO 9669, Series 1 freight containers:;Interface connections for tank container

27、s 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 14564 and the following apply. 3.1 manhole opening in the tank which includes the sealing, the manlid and fastenings BS EN 12561-6:2011EN 12561-6:2011 (E) 5 4 Requirements 4.1 Threaded fasteners The th

28、readed fasteners used for manholes shall conform to the requirements of EN ISO 898-1 and EN 20898-2. NOTE To avoid any crack or damage of a tank in case of an accident, it is recommended to use only threaded fasteners with no sharp edges and only in the shortest possible length. 4.2 Dimensions Nomin

29、al diameter of manhole shall be 500 mm. The figures of this document are given for a nominal diameter of manhole equal to 500 mm, Values depending on the diameter of the manhole shall be adapted to the nominal diameter All dimensions are given in millimetres. Unless otherwise indicated in this Europ

30、ean Standard, tolerances of EN ISO 286-1 apply for all dimensions. 5 End fitted manhole for gas tank wagons 5.1 Position of manhole The centre of the manhole shall be positioned on the longitudinal centre line of one end of the tank wagon. For easier access inside the tank, it is recommended that it

31、 is positioned according to Figure 1. NOTE For easier access to the tank, one handle above the manhole and inside the tank should be fitted. BS EN 12561-6:2011EN 12561-6:2011 (E) 6 Dimensions in millimetres Key 1 centre line of the tank Figure 1 Positioning of manhole 5.2 Ring and plate 5.2.1 Genera

32、l Ring and plate shall be calculated according to EN 14025. The plate shall be equipped with a minimum of one lifting point. 5.2.2 Dimensions Dimensions shall be in accordance with Figure 2. BS EN 12561-6:2011EN 12561-6:2011 (E) 7 Dimensions in millimetres Figure 2 Dimensions of ring and plate 5.2.3

33、 Surface parameters To ensure static liquid tightness and interchangeability of gaskets the maximum profile height (Rt) of surface defects according to EN ISO 4287 of gasket seat shall be less than 16 m. 5.2.4 Tolerances Non specified tolerances shall be in accordance with those of flanges DN 500 of

34、 ISO 7005-1:1992. 5.3 Gaskets The dimensions of the gasket shall be in accordance with Figure 3. BS EN 12561-6:2011EN 12561-6:2011 (E) 8 Dimensions in millimetres Figure 3 Gasket dimensions The average outside diameter obtained by measurements on two perpendicular diameters shall be 550 mm with a li

35、mit deviation of (0/- 1,5) mm. For flat gaskets made from fibre/elastomer or plastics, the thickness limit deviation is 0,20 mm. For metal plastics gaskets, the thickness limit deviation is (+ 0,5/ 0) mm. 6 Top fitted manhole for gas tank wagons This manhole is for gas tank wagons for which RID does

36、 not permit openings below the surface level of the liquid. Standard flanges DN 500 of ISO 7005-1:1992 and corresponding gaskets shall be used. Ring and plate shall be calculated according to EN 14025. The manlid shall be fitted with equipment defined in Figure 4, Figure 5 and Figure 6. The manlid s

37、hall be equipped with a minimum of three lifting points. All connecting and blind flanges of the external valves shall conform to face B of ISO 7005-1:1992. The liquid phase valves shall be painted red. BS EN 12561-6:2011EN 12561-6:2011 (E) 9 Dimensions in millimetres Key 1 liquid phase 2 gas phase

38、3 liquid phase 4 valves, connecting flange DN 40 PN 40 Type 21A, blind flange 4 valves, connecting flange DN 40 PN 40 Type 21A, blind flange 5 external valve flange 6 internal valve flange 7 manhole cover 8 tank wagon longitudinal axis Figure 4 Arrangement of valves on manlid BS EN 12561-6:2011EN 12

39、561-6:2011 (E) 10 Dimensions in millimetres Key 1 4 holes for hexagon socket head cap screws M 16 2 4 holes for stud M 16 Figure 5 Dimensions of internal valve flange Dimensions in millimetres Figure 6 Dimensions of recess in the manlid for internal valve flange BS EN 12561-6:2011EN 12561-6:2011 (E)

40、 11 7 Bolted manhole for liquid substances Standard flanges DN 500 according to ISO 7005-1:1992 and corresponding gaskets shall be used. Ring and plate shall be calculated according to EN 14025. The manlid shall be fitted with at least two lifting points, If handles are used, they shall be in accord

41、ance with Figure 7. Nozzles for loading or unloading on manlid are permitted. Dimensions in millimetres Figure 7 Manlid handle - minimum dimensions 8 Swing bolt manholes for liquid substances 8.1 General Swing bolts manholes shall either be in accordance with this European Standard or with ISO 9669.

42、 Swing bolt manholes with four wing nuts according to Figure 8 are not allowed on tank wagons with a test pressure greater than 0,4 MPa. 8.2 General arrangement Where tank wagons with a test pressure up to 0,4 MPa are fitted with a swing bolt manhole, this manhole shall be in accordance with Figure

43、8. They shall be fitted with swing bolts and wing nuts in accordance with 8.3, 8.4 and 8.5. There shall be sufficient clearance around the manhole hinge pin to allow the manlid seal to seat evenly. Dimension l1from Figure 8 shall allow easy release of the swing bolt. The top surface of the neck ring

44、 shall be in the horizontal plane. The manlid shall be equipped with a device which will release tank pressure prior to the swing bolts being swung down. An example to achieve this is given in Figure 8 cross section BB. BS EN 12561-6:2011EN 12561-6:2011 (E) 12 Dimensions in millimetres Key 1 hole fo

45、r venting 2 hole with diameter 15 for custom sealing Figure 8 Main dimensions for swing bolt manholes Type and space for connections could be different with agreement between customer and manufacturer. 8.3 Swing bolts Swing bolts shall be in accordance with Figure 9. BS EN 12561-6:2011EN 12561-6:201

46、1 (E) 13 Dimensions in millimetres Key 1 head spherical 2 cold rolled thread Class of the bolt according to EN ISO 898-1. Figure 9 Swing bolt 8.4 Wing nuts Wing nuts shall be in accordance with Figure 10. Dimensions in millimetres Class of the nut according to EN 20898-2. Figure 10 Wing nut BS EN 12

47、561-6:2011EN 12561-6:2011 (E) 14 8.5 Swing bolt hinge pin The hinge pin shall have a diameter of 20 mm and shall be removable without heating or cutting. It shall be capable of being customs sealed. 8.6 Gasket The dimensions of the gasket shall be in accordance with Figure 11 ( 535 is valid only for

48、 500 manhole). Dimensions in millimetres Figure 11 Gasket dimensions BS EN 12561-6:2011EN 12561-6:2011 (E) 15 Bibliography 1 EN 12972, Tanks for transport of dangerous goods Testing, inspection and marking of metallic tanks 2 RID, Regulations concerning the International Carriage of Dangerous Goods

49、by Rail1)implementing Commission Directives 2003/28/EC and 2003/29/EC 1)Commonly known as RID. This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporate