DOD A-A-50811-1981 ADHESIVE TAPE SURGICAL 1 INCH BY 1-1 2 YARDS 100S《100S 1-1 2码1英寸外科胶带》.pdf

《DOD A-A-50811-1981 ADHESIVE TAPE SURGICAL 1 INCH BY 1-1 2 YARDS 100S《100S 1-1 2码1英寸外科胶带》.pdf》由会员分享，可在线阅读，更多相关《DOD A-A-50811-1981 ADHESIVE TAPE SURGICAL 1 INCH BY 1-1 2 YARDS 100S《100S 1-1 2码1英寸外科胶带》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、A - A - 5 O 8 1 .l Auaust 5, 1981 COMMERCIAL ITEM DESCRIPTION ADHESIVE TAPE, SURGICAL, 1 inch by 1-1/2 yards, 100s This comercial item description covers a short length, adhesive tape which shall be suitable for use in medical and surgical procedures. Sal ient characteri stics : The tape shall be a

2、hypo-reactive, porous, pressure-sensi tive, surgical adhesive tape manufactured entirely of synthetics. The adhesive tape shall be capable of being torn by hand across its width, shall be resistant to water, shall be coated on one side with adhesive and shall not cause adverse reactions with human s

3、kin, either physically or chemically. The adhesive tape shall be one inch wide and shall have a useable length of one and one half yards and shall be evenly wound with the adhesive mass to the inside, on a paper core having an inside diameter of one inch. The adhesive tape shall meet the requirement

4、s of Adhesive Tape, U.S.P., except for tensile strength and adhesive strength as noted below. The backing material shall be ethylene/vinyl acetate and the backing shall be perforated and clear. The adhesive shall be acrylic and shall be clear. Performance. P roper ty Requirement Method pound/inch of

5、 width The adhesive tape shall comply with the fol 1 owing requirements. 34.2 i/ Tensi 1 e breaki ng streng th, 3.5 minimum - U1 timate elongation: percent 50 minimum - 34.2 i/ Adhesion to steel, ounces per inch of width 10.2 1/ 15 minimum - D726-59-A 2) Porosity, seconds 500 maximum - Unwind (oz./i

6、n.) 20 maximum - 80.2 1/ i/ Federal Test Method Standard 147. r/ - American Society for Testing and Materials. Resistance to water. then dried for 24 hours at room temperature the tape shall comply with the unwind and adhesion to steel requirements. After rolls of adhesive tape are soaked in water f

7、or 72 hours Inspection/test aating period. The inspection test dating period shall be 36 months. Not more than 3 months shall have elapsed from the date of manufacture of the adhesive tape to the date of delivery to the Government. Workmanship. The end item shall be uniform in quality and free from

8、foreign matter and any defects that will affect life, serviceability, or appearance. Packaging and packing quantities. Unit. Box (BX). One box containing one hundred wound strips of tape, as specified, constitutes one unit. Shipping container shall contain five units. TW DOCUMENT CONTAINS PACES FSC

9、6510 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50811 b5 W 7777774 0025754 2 W A-A-5081 1 Contractor certification. The contractor shall certify that the product offered meets the sal lent characteristics of the description and conforms to t

10、he producers own drawings, specifications, standards, and quality assurance practices, and is the same as the product offered for sale in the comercial marketplace. require proof of such conformance prior to first delivery and thereafter as may be other- wise provided for under the provisions of the

11、 contract. Regulatory requirements. compliance by their subcontractors/suppl iers, with the requirements of the Federal Food, Drug and Cosmetic Act and regulations promulgated thereunder, and the requirements of all other applicable Federal and State statutes and regulations. Recovered material s. O

12、fferors/contractors are encouraged to use recovered materi al in accordance with Public Law 94-580 to the maximum extent practical, Preservation, packaging, and packing. Unless otherwise specified, preservation, pack- aging, and packing shall be to a degree of protection to preclude damage to contai

13、ners and/or contents thereof under normal shipping conditions, hand1 ing, etc. , involving ship- ment from the supply source to the receiving activity, plus reshipment from receiving activity, and conforms to applicable carriers rules and regulations. For information only. The following product, as

14、of the date of this document, are purported by the following company to meet the salient characteristics of the item described herein: The Government reserves the right to The offeror/contractor shall comply, and be responsible for . Minnesota Mining and Manufacturing Company NOTE: The following National Stock Number is covered by this document: 6510-01-060-1639 Custodians: Army - MD Navy - MS Air Force - 03 44403 Pr epar i ng Ac ti v i ty : DoD - MB Agent: DLA - DM Project No. 6510-0667 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-