DLA SMD-5962-11203 REV D-2012 MICROCIRCUIT LINEAR 1 MHz to 4 GHz 80 dB LOGARITHMIC AMPLIFIER DETECTOR CONTROLLER MONOLITHIC SILICON.pdf

《DLA SMD-5962-11203 REV D-2012 MICROCIRCUIT LINEAR 1 MHz to 4 GHz 80 dB LOGARITHMIC AMPLIFIER DETECTOR CONTROLLER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-11203 REV D-2012 MICROCIRCUIT LINEAR 1 MHz to 4 GHz 80 dB LOGARITHMIC AMPLIFIER DETECTOR CONTROLLER MONOLITHIC SILICON.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHEET REV SHEET 15 16 17 18 19 20 21 22 23 24 25 26 REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MIC

2、ROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY CHARLES F. SAFFLE MICROCIRCUIT, LINEAR, 1 MHz to 4 GHz, 80 dB LOGARITHMIC AMPLIFIER DETECTOR / CONTROLLER, MONOLITHIC SILICON DRAWING APPROVAL DATE

3、12-06-22 AMSC N/A REVISION LEVEL SIZE A CAGE CODE 67268 5962-11203 SHEET 1 OF 26 DSCC FORM 2233 APR 97 5962-E082-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11203 DLA LAND AND MARITIME COLUMBUS, OHIO 4

4、3218-3990 REVISION LEVEL SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in

5、the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 R 11203 01 V X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device c

6、lass designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2

7、 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 ADL5513 1 MHz to 4 GHz logarithmic detector/controller 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as

8、 follows: Device class Device requirements documentation Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X CDFP4-F16 16 Flat pack 1.2.5 L

9、ead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11203 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990

10、REVISION LEVEL SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VPOS) 5.5 V Voltage at VSET pin 0 V to VPOSInput power (single ended, 50 ) 20 dBm Internal power dissipation (PD) 220 mW Maximum junction temperature (TJ) +150C Lead temperature (soldering, 60 seconds) 260C

11、 Storage temperature range -65C to +150C Thermal resistance, junction-to-case (JC) 53C/W 2/ Thermal resistance, junction-to-ambient (JA) . 66C/W 3/ 1.4 Recommended operating conditions. Supply voltage (VPOS) 2.7 V to 5 V Ambient operating temperature range (TA) . -55C to +125C 1.4.1 Operating perfor

12、mance characteristics. 4/ Dynamic range: 100 MHz, 3.0 dB . 67 dBm 900 MHz, 3.0 dB . 74 dBm 2140 MHz, 3.0 dB . 76 dBm 4000 MHz, 3.0 dB . 70 dBm 100 MHz, 1.0 dB . 58 dBm 900 MHz, 1.0 dB . 69 dBm 2140 MHz, 1.0 dB . 68 dBm 4000 MHz, 1.0 dB . 61 dBm 100 MHz, 0.5 dB . 50 dBm 900 MHz, 0.5 dB . 67 dBm 2140

13、MHz, 0.5 dB . 66 dBm 4000 MHz, 0.5 dB . 56 dBm Input level, 1.0 dB: 100 MHz, radio frequency (RF) maximum 6 dBm 100 MHz, RF minimum . -52 dBm 900 MHz, RF maximum 7 dBm 900 MHz, RF minimum . -62 dBm 2140 MHz, RF maximum 2 dBm 2140 MHz, RF minimum . -70 dBm 4000 MHz, RF maximum 6 dBm 4000 MHz, RF mini

14、mum . -55 dBm _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Measurement taken under absolute worst case conditions. Data taken with a thermal camera for highest pow

15、er density location. See MIL-STD-1835 for average package thermal numbers. 3/ Measurement taken under absolute worst case conditions. Data taken with a thermal camera for highest power density location. 4/ Unless otherwise specified, VPOS= 2.7 V to 5 V, VTADJis per paragraph 6.7.5. TA= +25C. Provide

16、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11203 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 4 DSCC FORM 2234 APR 97 1.4.1 Operating performance characteristics continued. 4/ RF input i

17、mpedance: 100 MHz 1.3 k 900 MHz 1.3 k 2140 MHz 0.5 k 4000 MHz 0.5 k RF input capacitance: 100 MHz 0.4 pF 900 MHz 0.4 pF 2140 MHz 0.5 pF 4000 MHz 0.4 pF VOUToutput capacitance: CLPF = open . 47 pF CLPF = 20 pF 1 nF VOUToutput noise, RF input = 100 MHz, 0 dBm: fnoise= 100 kHz, CLPF = open . 145 nV / H

18、z fnoise= 100 kHz, CLPF = 1 nF 82 nV / Hz TADJ response time, TADJ low (enable) to VOUT100%, TADJ high (disable) to VOUT10%, RF input = 0 dBm, 100 MHz, 1 s pulse width Enable time, CLPF = open . 84 ns Enable time, CLPF = 1000 pF 10.8 s Disable time, CLPF = open 165 ns Disable time, CLPF = 1000 pF .

19、1.2 s TADJ input Impedance, TADJ = 0.9 V, sourcing 70 A . 13 k 1.5 Radiation features. Maximum total dose available (dose rate = 50 300 rads(Si)/s) . 100 krads(Si) 5/ _ 5/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end

20、point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883, method 1019, condition A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11203 DLA LAND AND MARITIME COL

21、UMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 5 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues

22、 of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard

23、Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order D

24、esk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regul

25、ations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modi

26、fication in the QM plan shall not affect the form, fit, or function as described herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V. 3.2.1 Case outline. The case out

27、line shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Block diagram. The block diagram shall be as specified on figure 2. 3.2.4 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the

28、 manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and pos

29、tirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I

30、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11203 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbo

31、l Conditions 1/ 2/ 3/ 4/ -55C TA +125C Group A subgroups Device type Limits Unit VPOS= 5.0 V unless otherwise specified Min Max RFINfrequency = 100 MHz Logarithmic slope 5/ Slope 4 01 19.4 22.6 mV/dB 5 20.2 21.6 6 20.4 22.3 M,D,P,L,R 4 19.4 22.6 Logarithmic intercept 5/ Intercept 4 01 -96.7 -79.3 dB

32、m 5 -96.9 -80.8 6 -96.5 -77.9 M,D,P,L,R 4 -96.7 -79.3 VOUTvoltage VO RFIN= -10 dB 4 01 1.45 1.81 V 5,6 0 2.65 M,D,P,L,R 4 1.45 1.81 RFIN= -30 dB 4 0 2.65 5,6 0 2.65 M,D,P,L,R 4 0 2.65 RFIN= -50 dB 4 0.59 0.99 5,6 0 2.65 M,D,P,L,R 4 0.59 0.99 Deviation from log linear 5/ Linear RFIN= -10 dB 4 01 -1.1

33、 1.1 dB error 5,6 -1.1 1.1 M,D,P,L,R 4 -1.1 1.1 RFIN= -30 dB 4 -0.6 0.6 5,6 -0.6 0.6 M,D,P,L,R 4 -0.6 0.6 RFIN= -50 dB 4 -2.1 2.1 5,6 -2.5 2.5 M,D,P,L,R 4 -2.1 2.1 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR

34、D MICROCIRCUIT DRAWING SIZE A 5962-11203 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ 3/ 4/ -55C TA +125C Group A subgroups Device type Limits Unit VPOS= 5.0 V unle

35、ss otherwise specified Min Max RFINfrequency = 900 MHz Logarithmic slope 5/ Slope 4 01 20.9 22.3 mV/dB 5 20.6 21.9 6 20.8 22.4 M,D,P,L,R 4 20.9 22.3 Logarithmic intercept 5/ Intercept 4 01 -102.2 -84.2 dBm 5 -102.4 -85.3 6 -102.5 -83.3 M,D,P,L,R 4 -102.2 -84.2 VOUTvoltage VO RFIN= -10 dB 4 01 0 2.65

36、 V 5,6 0 2.65 M,D,P,L,R 4 0 2.65 RFIN= -30 dB 4 0 2.65 5,6 0 2.65 M,D,P,L,R 4 0 2.65 RFIN= -50 dB 4 0 2.65 5,6 0 2.65 M,D,P,L,R 4 0 2.65 Deviation from log linear 5/ Linear RFIN= -10 dB 4 01 -1.1 1.1 dB error 5,6 -1.1 1.1 M,D,P,L,R 4 -1.1 1.1 RFIN= -30 dB 4 -0.6 0.6 5,6 -0.6 0.6 M,D,P,L,R 4 -0.6 0.6

37、 RFIN= -50 dB 4 -2.1 2.1 5,6 -2.5 2.5 M,D,P,L,R 4 -2.1 2.1 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11203 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL S

38、HEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ 3/ 4/ -55C TA +125C Group A subgroups Device type Limits Unit VPOS= 5.0 V unless otherwise specified Min Max RFINfrequency = 2140 MHz Logarithmic slope 5/ Slope 4 01 19.7 24.2 mV/dB 5

39、 19.2 23.8 6 21.3 23.7 M,D,P,L,R 4 19.7 24.2 Logarithmic intercept 5/ Intercept 4 01 -89.8 -71 dBm 5 -92.8 -68.4 6 -93.6 -67 M,D,P,L,R 4 -89.8 -71 VOUTvoltage VO RFIN= -10 dB 4 01 0 2.65 V 5,6 0 2.65 M,D,P,L,R 4 0 2.65 RFIN= -30 dB 4 0 2.65 5,6 0 2.65 M,D,P,L,R 4 0 2.65 RFIN= -45 dB 4 0 2.65 5,6 0 2

40、.65 M,D,P,L,R 4 0 2.65 Deviation from log linear 5/ Linear RFIN= -10 dB 4 01 -1.6 1.6 dB error 5,6 -1.65 1.65 M,D,P,L,R 4 -1.6 1.6 RFIN= -30 dB 4 -0.6 0.6 5,6 -0.6 0.6 M,D,P,L,R 4 -0.6 0.6 RFIN= -45 dB 4 -1.6 1.6 5 -2.0 2.0 6 -1.2 1.2 M,D,P,L,R 4 -1.6 1.6 See footnotes at end of table. Provided by I

41、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11203 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 9 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Con

42、ditions 1/ 2/ 3/ 4/ -55C TA +125C Group A subgroups Device type Limits Unit VPOS= 5.0 V unless otherwise specified Min Max RFINfrequency = 4000 MHz Logarithmic slope 5/ Slope 4 01 22.4 25.1 mV/dB 5 22.7 25.9 6 21.2 25 M,D,P,L,R 4 22.4 25.1 Logarithmic intercept 5/ Intercept 4 01 -92.9 -74.7 dBm 5 -9

43、2.2 -74.8 6 -96 -75.4 M,D,P,L,R 4 -92.9 -74.7 VOUTvoltage VO RFIN= -10 dB 4 01 0 2.65 V 5,6 0 2.65 M,D,P,L,R 4 0 2.65 RFIN= -30 dB 4 0 2.65 5,6 0 2.65 M,D,P,L,R 4 0 2.65 RFIN= -50 dB 4 0 2.65 5,6 0 2.65 M,D,P,L,R 4 0 2.65 Deviation from log linear 5/ Linear RFIN= -10 dB 4 01 -1.3 1.3 dB error 5 -1.3

44、5 1.35 6 -1.35 1.35 M,D,P,L,R 4 -1.3 1.3 RFIN= -30 dB 4 -0.6 0.6 5,6 -0.6 0.6 M,D,P,L,R 4 -0.6 0.6 RFIN= -50 dB 4 -2.5 2.5 5,6 -2.9 2.9 M,D,P,L,R 4 -2.5 2.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICRO

45、CIRCUIT DRAWING SIZE A 5962-11203 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 10 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ 3/ 4/ -55C TA +125C Group A subgroups Device type Limits Unit VPOS= 5.0 V unless oth

46、erwise specified Min Max Setpoint input (VSET) section. Logarithmic scale factor LSF RFINfrequency = 100 MHz 4,6 01 39 53 dB/V 5 37 53 M,D,P,L,R 4 39 53 RFINfrequency = 900 MHz 4,6 39 53 5 37 53 M,D,P,L,R 4 39 53 RFINfrequency = 2140 MHz 4,6 39 53 5 37 53 M,D,P,L,R 4 39 53 RFINfrequency = 4000 MHz 4

47、,6 39 53 5 37 53 M,D,P,L,R 4 39 53 Output interface (VOUT) section. Voltage swing VOmaxVSET= 1.0 V, RFIN= -5 dBm, 1 01 4.79 VPOSV VOUTnot connected to VSET2,3 4.79 VPOSM,D,P,L,R 1 4.79 VPOSVOminVSET= 1.0 V, RFIN= open, 1 0 0.06 VOUTnot connected to VSET2,3 0 0.06 M,D,P,L,R 1 0 0.06 Current source/si

48、nk 6/ 7/ IOsource1 01 -44 mA 2 -55 3 -40 IOsink1 0.55 2 0.55 3 0.55 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11203 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 11 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characte