DLA AN104201 THRU AN104300 REV 3-1986 BOLT - DRILLED HEX HEAD 6 HOLES 500-20.pdf

《DLA AN104201 THRU AN104300 REV 3-1986 BOLT - DRILLED HEX HEAD 6 HOLES 500-20.pdf》由会员分享，可在线阅读，更多相关《DLA AN104201 THRU AN104300 REV 3-1986 BOLT - DRILLED HEX HEAD 6 HOLES 500-20.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、ANLOq201 THRU AN104300 REV 3 53 7777715 0000252 O .120f FED. SUP. CLASS I 5306 K TO FULL THD -MATERIAL IDENTIFICATION PER AMS2800. RAISED OR DEPRESSED .O10 MAX ,344 ,264 .O47 x 45 ,160 TO POINT APPROX -4 .O16 OR CHAMFE DRILL .i88 TO DEPTH SHOWN AS SHOWN WIT .500-20UNF-3A .o30 SPEC MIL-S-774 L 1.000

2、1 .o62 1.125 1. i88 1.250 1.312 1.375 1.438 1.500 1.562 1.625 1.688 1.750 K t .o00 - .o60 lai (a) (a) . !:A .250 .312 .375 .4 38 .500 THIS SURFACE hST BE SQUARE WITH SHANK WITHIN .o03 FIR. CHAMFER 30 TO .750 DIA (OPPOSITE SIDE OPTIONAL) SECTION THRU THREAD PROFILE i .812 AN104206 1.875 AN104207 1.93

3、8 11 104208 2.000 AN104209 2.062 AN104210 2.125 AN104211 2. i88 AN104212 2.250 AN104213 2.375 AN104214 2.500 AN104215 2.625 AN104216 2.750 11 AN104217 1 2.875 AN104218 3.000 +.O00 PART NO. I -.:60 I( AN104219 3. i25 2; 1 AN104220 11 3,250 .688 104221 3.375 .750 1 AN104222 11 3.500 .812 AN104223 3.62

4、5 .875 AN104224 3.750 .938 I AN104225 11 3.875 1.000 AN104226 4.000 1.125 AN104227 4.125 1,250 i AN104228 11 4.250 1.375 AN104229 4.375 1.500 AN104230 4.500 1.625 AN104231 4.625, 1.750 AN104232 4.750 K + . O00 - .o60 1.875 2.000 2.125 2.250 2.500 2.375 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500

5、 AN104233 4.875 3.625 AN104234 11 5.000 I 3.750 AN104235 5.125 3 .875 5.250 AN104239 5.625 4.375 AN104240 5.750 4.500 AN104241 5.875 4.625 AN104242 6.000 4.750 AN104243 AN104244 AN104245 AN104246 (a) THREAD TO HEAD. MAXIMUM TWO IMPERFECT THREADS. NOTE: (1) SHANK SHALL BE STRAIGHT WITHIN ,002 FIR. PE

6、R INCH OF BOLT LENGTH. (2) THE CONCENTRLCITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMETER AND HEXAGON SHALL BE WITHIN .O23 FIR. MATERIAL: STEEL AMs6322 HARDNESS: ROCKWELL C26-32 FINISH: CADMIUM PLATE ANS240

7、0 SURFACE ROUGHNESS: AS107 MANUFACTURING SPECIFICATION: AMs7452 3 INSPECTION: ALL PARTS SHALL UNDERGO MAGNETIC NSPECTION N CCORD NCE WITH AMS26 PART NO. AN104247 AN104248 AN104249 AN104250 AN104251 AN104252 AN104253 AN104254 AN104255 AN104256 BREAK SHARP EDGES .003-.O15 UNLESS OTHERWISE SPECIFIED. D

8、IMENSIONS IN INCHES. UIoLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIMENSIONS t.O1O. ANGULAR OIM6NSIONS +2 . DO NOT USE UNASSIGNED PART NUMBERS. INACTIVE FOR NEW DESIGN AFTER 3 MARCH 1969 NO SUPERSEDING STANDARD. THIS STANDARD WAS DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILITY PARTS C

9、OMMITTEE OF THE SAE. AIR FORCE-NAVY AERONAUTICAL STANDARD AN104 201 AN104 300 P.A. Ar-Il T HRU CUST . NAVY - AS BOLT - DRILLED HEX HEAD, 6 HOLES, .500-20 ARMY - AV / I THIS DOCUMENT CONTAINS i- . PAGES. Project NO. 5306-1026 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-