BS ISO 1174-1-2011 Assembly tools for screws and nuts Driving squares Driving squares for hand socket tools《螺丝和螺母用装配工具 驱动方头 手动套筒工具用驱动方头》.pdf

《BS ISO 1174-1-2011 Assembly tools for screws and nuts Driving squares Driving squares for hand socket tools《螺丝和螺母用装配工具 驱动方头 手动套筒工具用驱动方头》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 1174-1-2011 Assembly tools for screws and nuts Driving squares Driving squares for hand socket tools《螺丝和螺母用装配工具 驱动方头 手动套筒工具用驱动方头》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 1174-1:2011Assembly tools for screws andnuts Driving squaresPart 1: Driving squares for hand socket toolsBS ISO 1174-1:2011 BRITISH STANDARDNational forewordThis British S

2、tandard is the UK implementation of ISO 1174-1:2011. The UK participation in its preparation was entrusted to T e c h n i c a l Committee MTE/15, Hand tools.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include

3、all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 67807 3 ICS 25.140.30 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Polic

4、y and Strategy Committee on 31 August 2011.Amendments issued since publicationDate T e x t a f f e c t e dBS ISO 1174-1:2011Reference numberISO 1174-1:2011(E)ISO 2011INTERNATIONAL STANDARD ISO1174-1Second edition2011-04-15Assembly tools for screws and nuts Driving squares Part 1: Driving squares for

5、 hand socket tools Outils de manuvre pour vis et crous Carrs dentranement Partie 1: Carrs dentranement pour outils main BS ISO 1174-1:2011ISO 1174-1:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilize

6、d in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 4

7、1 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reservedBS ISO 1174-1:2011ISO 1174-1:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

8、 (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations,

9、governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/

10、IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the me

11、mber bodies casting a vote. ISO 1174-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pliers and nippers. This second edition cancels and replaces the first edition (ISO 1174-1:1996), Table 1 and Figure 2 of which have been technic

12、ally revised. ISO 1174 consists of the following parts, under the general title Assembly tools for screws and nuts Driving squares: Part 1: Driving squares for hand socket tools Part 2: Driving squares for power socket tools BS ISO 1174-1:2011BS ISO 1174-1:2011INTERNATIONAL STANDARD ISO 1174-1:2011(

13、E) ISO 2011 All rights reserved 1Assembly tools for screws and nuts Driving squares Part 1: Driving squares for hand socket tools 1 Scope This part of ISO 1174 specifies the dimensions, separation force and designation of driving squares for hand socket tools. NOTE Driving squares for power socket t

14、ools are dealt with in ISO 1174-2. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

15、applies. ISO 3, Preferred numbers Series of preferred numbers ISO 286-1, Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Bases of tolerances, deviations and fits 3 Dimensions 3.1 General Nominal dimensions of driving squares, in millimetres, have been

16、selected from the values of the R 10 series of preferred numbers in accordance with ISO 3. 3.2 Interchangeability Driving square maximum and minimum dimensions have been selected for the types of tool described in 3.3 and 3.4 so as to allow for interchangeability, whatever the measurement system use

17、d. Deviations, between maximum and minimum dimensions correspond for s1, to tolerances of grade IT11 in accordance with ISO 286-1, and for s2, to tolerances of grade IT13 in accordance with ISO 286-1. When using male square drives with a plunger retainer instead of a ball, only female squares with r

18、etaining holes as opposed to recesses should be used. BS ISO 1174-1:2011ISO 1174-1:2011(E) 2 ISO 2011 All rights reserved3.3 Male squares See Figures 1 and 2 and Table 1. Figure 1 Type A with ball Figure 2 Type B with plunger retainer Table 1 Male square dimensions Types A and B Dimensions in millim

19、etres s1d1d2e1l1l3l4r1Typeanom. max. min. max. max. min. max. nom. tol. min.bmax. A (B) 6,3 6,35 6,26 3 2 8,4 8,0 7,5 4 0,2 0,9 0,5 A (B) 10 9,53 9,44 5 2,6 12,7 12,2 11 5,5 0,2 0,9 0,6 A (B) 12,5 12,70 12,59 6 3 16,9 16,3 15,5 8 0,3 1,0 0,8 B (A) 20 19,05 18,92 7 4,3 25,4 24,4 23 10,2 0,3 1,0 1,2 B

20、 25 25,40 25,27 5 34,0 32,4 28 15 0,3 1,0 1,6 NOTE It is not recommended that types B and C be used together. aTypes given in brackets are non-preferred. bRounded values given, based on the calculation l4,min= s2,max s1,min+ 0,5 mm. BS ISO 1174-1:2011ISO 1174-1:2011(E) ISO 2011 All rights reserved 3

21、3.4 Female squares See Figures 3 and 4 and Table 2. aChamfered or rounded in conformity with radius, r1, of the male square. Figure 3 Type C aChamfered or rounded in conformity with radius, r1, of the male square. Figure 4 Type D BS ISO 1174-1:2011ISO 1174-1:2011(E) 4 ISO 2011 All rights reservedTab

22、le 2 Female square dimensions Types C and D Dimensions in millimetres s2d3e2l2l3r2t1Typeanom. max. min. min. min. min. nom. tol. C, D 6,3 6,63 6,41 2,5 8,5 8 4 0,2 C (D) 10 9,80 9,58 5 12,9 11,5 5,5 0,2 C (D) 12,5 13,03 12,76 6 17,1 16 8 0,3 4 3 D 20 19,44 19,11 6 25,6 24 10,2 0,3 4 3,5 D 25 25,79 2

23、5,46 6,5 34,4 29 15 0,3 6 4 NOTE It is not recommended that types B and C be used together. aTypes given in brackets are non-preferred. 4 Separation force When the male and female squares are locked, the force that shall be applied in order to separate the two parts shall not be less than 4 N for th

24、e 6,3 mm square, 11 N for the 10 mm square, 25 N for the 12,5 mm square, and 45 N for the 20 mm square. The force shall be applied gradually along the axis of the squares. NOTE The values of separation force apply to tools in the delivery condition and to parts supplied by one manufacturer. 5 Design

25、ation A driving square for hand socket tools in accordance with this part of ISO 1174 shall be designated by a) “Male square” or “Female square”, as appropriate; b) reference to this part of ISO 1174, i.e. ISO 1174-1; c) type; d) nominal dimension of driving square, in millimetres. EXAMPLE A male dr

26、iving square for hand socket tools type A with nominal dimension 12,5 mm is designated as follows: Male square ISO 1174-1 A 12,5 BS ISO 1174-1:2011BS ISO 1174-1:2011ISO 1174-1:2011(E) ICS 25.140.30 Price based on 4 pages ISO 2011 All rights reserved This page deliberately left blankBSI is the indepe

27、ndent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards w

28、orldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve th

29、e quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +4

30、4 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly usi

31、ng acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosuppl

32、y the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005E

33、mail: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase pr

34、iceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI w

35、ebsite at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmit

36、ted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: