BS EN 3841-303-2005 Aerospace series - Circuit breakers - Test methods - Dielectric strength《航空航天系列 断路器 试验方法 介电强度》.pdf

《BS EN 3841-303-2005 Aerospace series - Circuit breakers - Test methods - Dielectric strength《航空航天系列 断路器 试验方法 介电强度》.pdf》由会员分享，可在线阅读，更多相关《BS EN 3841-303-2005 Aerospace series - Circuit breakers - Test methods - Dielectric strength《航空航天系列 断路器 试验方法 介电强度》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3841-303:2004 Circuit breakers Test methods Part 303: Dielectric strength The European Standard EN 3841-303:2004 has the status of a British Standard ICS 49.060 BS EN 3841-303:2004 This British Standard was published under the authority of the Standards Policy

2、 and Strategy Committee on 22 February 2005 BSI 22 February 2005 ISBN 0 580 45526 2 National foreword This British Standard is the official English language version of EN 3841-303:2004. The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical a

3、nd fibre optic technology, to Subcommittee ACE/6/5, Circuit breakers, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications r

4、eferred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary pr

5、ovisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposa

6、ls for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover. The BSI cop

7、yright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN3841303 December2004 ICS49.060 Englishversion AerospaceseriesCircuitbreakersTestmethodsPart303: Dielectrics

8、trength SriearospatialeDisjoncteursMthodesdessais Partie303:Rigiditdilectrique LuftundRaumfahrtSchutzschalterPrfverfahrenTeil 303:Spannungsfestigkeit ThisEuropeanStandardwasapprovedbyCENon10September2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgi

9、vingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversionina

10、nyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Icelan

11、d,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrig

12、htsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN3841303:2004:EEN 3841-303:2004 (E) 2 Contents Page 1 Scope 4 2 Normative references 4 3 Method 4 EN 3841-303:2004 (E) 3 Foreword This document (EN 3841-303:2004) has been prepared by the European Association of

13、Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation t

14、o CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. According to the CEN/CENELEC Internal Regulation

15、s, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

16、 Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 3841-303:2004 (E) 4 1 Scope This standard specifies a method of verifying the dielectric strength of circuit breakers. It shall be used together with EN 3841-100. 2 Normative references The following referenced

17、documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3841-100, Aerospace series Circuit breakers Test methods Part 100: Gene

18、ral 3 Method 3.1 Procedure The tests shall be taken after stabilization at environmental conditions specified in EN 3841-100. The a.c. test voltage (50 Hz) shall be applied progressively with a maximum rate of increase of 250 V/s. Measurements shall be taken in the closed and open positions between

19、all the points as indicated below according to the values defined in the product standard. When these voltages have been reached, they shall be maintained for 1 min. The circuit breakers shall be monitored for leakage current and possible breakdown. Measuring points: Measurements shall be taken with

20、 the circuit breakers in the “on” setting (closed position): between the terminals of each individual pole and all other connections including signal contacts; between all connections including signal contacts and earth (mounting). Measurements shall be taken with the circuit breakers in the “off” s

21、etting (open position): between each connection and all other connections including signal contacts; between all connections including signal contacts and earth. 3.2 Requirement For all admissible temperatures at ground and max. altitude, the values recorded shall meet the requirements of the produc

22、t standard. There shall be no leakage current 1 mA, breakdown or defect. blankBS EN 3841-303:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europ

23、e and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our produc

24、ts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BS

25、I offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001.

26、 Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.

27、Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Con

28、tact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membershi

29、p Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright

30、 Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in an

31、y form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.