ASTM F1183-1996(2017) Standard Specification for Aluminum Alloy Chain Link Fence Fabric《铝合金连接链环栏栅织物的标准规格》.pdf

《ASTM F1183-1996(2017) Standard Specification for Aluminum Alloy Chain Link Fence Fabric《铝合金连接链环栏栅织物的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1183-1996(2017) Standard Specification for Aluminum Alloy Chain Link Fence Fabric《铝合金连接链环栏栅织物的标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1183 96 (Reapproved 2017)Standard Specification forAluminum Alloy Chain Link Fence Fabric1This standard is issued under the fixed designation F1183; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last rev

2、ision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers aluminum alloy chain linkfence fabric for commercial, industrial, and residential uses.1.2 The value

3、s stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This international standard was developed in accor-dance with internationally recognized princ

4、iples on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A700 Guide for Packaging, Markin

5、g, and Loading Methodsfor Steel Products for ShipmentB211 Specification for Aluminum and Aluminum-AlloyRolled or Cold Finished Bar, Rod, and Wire2.2 Federal Standards:Fed. Std. No. 123 Marking for Shipment, Civil Agencies32.3 Military Standards:MILSTD129 Marking for Shipment and Storage33. Terminolo

6、gy3.1 Definitions of Terms Specific to This Standard:3.1.1 chain link fence fabrica fencing material made fromwire helically wound and interwoven in such a manner as toprovide a continuous mesh without knots or ties, except in theform of knuckling or of twisting the ends of the wires to formthe selv

7、age of the fabric.3.1.2 diamond countthe number of diamond openingsfrom one edge of the fabric to the other. The diamond count ofa given fabric shall begin at the first completed diamond at oneedge and continue to the unfinished (one-half) of full openingat the other edge.3.1.3 knucklinga term used

8、to describe the type of selvageobtained by interlocking adjacent pairs of wire ends and thenbending the wire ends back into a loop. The loop shall beclosed or nearly closed to a measurement less than the diameterof the wire.3.1.4 twistinga term used to describe the type of selvageobtained by twistin

9、g adjacent pairs of wire ends together in aclose helix of 112 machine turns, which is equivalent to threefull twists, and cutting the wire ends at an angle. The wire endsbeyond the twist shall be at least14 in. (6.35 mm) long. Thistype of selvage is not used on fabric with a mesh size of lessthan 2

10、in.4. Ordering Information4.1 Orders for chain link fence fabric purchased to thisspecification shall include the information given in 4.1.1through 4.1.8.4.1.1 Quantity (Section 13),4.1.2 Size of mesh (Section 7),4.1.3 Size of wire (Section 8),4.1.4 Height of fabric (Section 9),4.1.5 Diamond count,

11、if specified (Section 6),4.1.6 Type of selvage (Section 10),4.1.7 Certification, if required (Section 16), and4.1.8 ASTM designation and year of issue.4.2 All rolls of fencing accepted by the purchaser shall bebilled on the basis of the original footage of the rolls prior tosampling, unless changed

12、by contractual arrangement.NOTE 1An example of a typical ordering description is as follows: 25rolls, 50 ft each, chain link fence fabric, aluminum alloy, 2 in. (50.8 mm)mesh, 0.148 in. (3.76 mm) wire, 60 in. high, knuckled both selvages, toASTM F1183 .5. Materials5.1 The wire from which the fabric

13、is woven shall conformto all requirements of alloy 6061, temper T94 described inSpecification B211.1This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Current edition approved Jun

14、e 1, 2017. Published July 2017. Originally approvedin 1988. Last previous edition approved in 2011 as F1183 - 96(2011). DOI:10.1520/F1183-96R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards v

15、olume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, P

16、A 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization

17、Technical Barriers to Trade (TBT) Committee.16. Weave6.1 The wire shall be woven throughout in the form ofapproximately uniform square mesh, having parallel sides andhorizontal and vertical diagonals of approximately uniformdimensions. The top and bottom of the fabric shall be knuckledor twisted as

18、specified in Section 10.6.2 A typical diamond count for each standard height isshown in Table 1. Other diamond counts are permissibleprovided that they are consistent within a lot. The purchaserhas the option to specify the diamond count (4.1.5).7. Size of Mesh7.1 The size of mesh shall be as indica

19、ted in Table 2.7.2 The permissible variation from the specified size ofmesh shall be 618 in. (3.175 mm) for all mesh sizes except 1in. (25.4 mm), and 6116 in. (1.5875 mm) for 1-in. (25.4 mm)mesh size.7.3 The size of mesh shall be determined by measuring theminimum clear distance between the wires fo

20、rming the parallelsides of the mesh, and calculated as the average of tworeadings taken at right angles to each other.8. Size of Wire8.1 Chain link fabric shall be fabricated from wire diametersas listed in Table 2, with a permissible variation from thespecified diameter of 60.005 in. (0.127 mm).9.

21、Height of Fabric9.1 Chain link fabric shall be furnished in the standardheights shown in Table 2. The height of fabric shall be theoverall dimension from ends of twists or knuckles. Permissiblevariation from the specified height shall be 61 in. (25.4 mm)for 134 in. (44.45 mm) and 2 in. (50.8 mm) mes

22、h and 612 in.(12.7 mm) for 1 in. (25.4 mm) mesh.10. Selvage10.1 Unless otherwise specified by the purchaser, fabricswith 2 in. (50.8 mm) mesh used in heights 60 in. (1524 mm)and under shall be knuckled at both selvages. Fabric of heights72 in. (1830 mm) and above shall be knuckled at one selvageand

23、twisted at the other.10.2 The selvages of all fabrics with meshes of less than 2in. shall be knuckled.NOTE 2Use of twisted selvages for fence fabric under 72 in. (1830mm) in height are not recommended because of consumer safety consid-erations.11. Breaking Strength11.1 The wire constituting the fabr

24、ic shall meet the mini-mum breaking strength requirements shown in Table 3.12. Finish12.1 Unless otherwise specified, the fabric shall have a millfinish. The purchaser may specify a caustic-cleaned, or etchedfinish, derived by chemical removal of the wire drawing andweaving lubricants after the fabr

25、ic is woven.13. Standard Length of Rolls13.1 The standard length of roll shall be 50 ft (15.24 m)61 %, except as otherwise agreed upon at the time ofpurchase.13.2 The length of roll shall be determined by unrolling aroll of fabric onto a flat surface and then exerting tension byappropriate means to

26、remove all slack. The tension appliedshall not reduce the actual height of the fabric by more than116 in. ft (1.5875 mm/m) of height or by more than12 in. (12.7mm) total, whichever is less.14. Sampling and Number of Tests14.1 One roll of every 50 rolls, or fraction thereof, in a lotshall be taken at

27、 random as a sample for test purposes. In nocase shall less than two samples be tested, except when the lotis less than 10 rolls, when only one roll shall be selected for thesample.14.2 Sample rolls selected shall be inspected for uniformityof weave (6.1), diamond count (6.2), size of mesh (Section

28、7),size of wire (Section 8), height of fabric (Section 9), selvage(Section 10), tensile strength (Section 11), and length (Section13).TABLE 1 Typical Diamond CountA,BDiameter ofWire, in.Size ofMesh, in.Height of Fabric, in.36 42 48 60 72 84 96 108 120 1440.192 2 1012 1212 1312 1712 2012 2412 2712 31

29、12 3412 41120.148 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.148 134 3112 3512 3912 47120.148 20232733394553616779AOther diamond counts are permitted. Refer to 6.2 of this specification.BSee Table X1.1 for metric equivalents.TABLE 2 Sizes of Wire and MeshASpecifiedDiameter ofWire, in.WireG

30、augeSizeSize ofMesh, in.Height of Fabric, in.0.192 6 2 36, 42, 48, 60, 72, 84, 96, 108,120, 1440.148 9 2 36, 42, 48, 60, 72, 84, 96, 108,120, 1440.148 9 134 . . . . . . 96, 108, 120,1440.148 9 1 36, 42, 48, 60, 72, 84, 96, 108,120, 144ASee Table X1.1 for metric equivalents.F1183 96 (2017)214.3 If an

31、y specimen fails to meet the requirements of thisspecification, the roll represented by the specimen shall berejected. Two additional rolls shall be inspected, both of whichshall meet the requirements in every respect; otherwise, the lotrepresented by the samples may be rejected.15. Inspection15.1 U

32、nless otherwise specified in the purchase order orcontract, the manufacturer is responsible for the performanceof all inspection and test requirements specified in this speci-fication. Except as otherwise specified in the purchase order orcontract, the manufacturer may use his own or any othersuitab

33、le facilities for the performance of the inspection and testrequirements, unless disapproval is expressed by the purchaserat the time the order is placed. The purchaser shall have theright to perform any of the inspection and tests set forth in thisspecification when such inspections and tests are d

34、eemednecessary to assure that the material conforms to prescribedrequirements.16. Certification16.1 When specified in the purchase order or contract, aproducers or suppliers certification shall be furnished to thepurchaser stating that the material was manufactured, sampled,tested, and inspected in

35、accordance with this specification, andhas been found to meet the requirements. When specified in thepurchase order or contract, a report of the test results shall befurnished.17. Packaging, Marking, and Loading17.1 Each length of chain link fence fabric shall be tightlyrolled and firmly tied. Each

36、roll shall carry a tag describing thetype of material, the specified wire size and mesh size, and thespecified length and height of fabric in the roll. Compliance ofthe fence fabric with Specification F1183 shall be marked, aswell as the name or mark of the manufacturer.17.2 Unless otherwise specifi

37、ed, packaging, marking, andloading for shipment shall be in accordance with PracticesA700.17.3 When specified in the contract or order, and for fencefabric being directly procured by or directly shipped to the U.S.government, marking for shipment, in addition to the require-ments specified in the co

38、ntract or order, shall be in accordancewith MIL-STD-129 for U.S. military agencies and in accor-dance with Fed. Std. No. 123 for civil agencies.18. Keywords18.1 aluminum alloy chain link fence fabric; chain linkfence, aluminum alloy; fence/fencing materials, chain linkAPPENDIXTABLE 3 Breaking Streng

39、th of WireSpecified Diameter of Wire,in. (mm)Minimum Breaking Strength,lbf (N)0.192 (4.88)0.148 (3.76)1560 (6939)925 (4114)F1183 96 (2017)3(Nonmandatory Information)X1. METRIC EQUIVALENTSX1.1 Approximate metric equivalents are given in TableX1.1.ASTM International takes no position respecting the va

40、lidity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is su

41、bject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headqu

42、arters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This stand

43、ard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or ser

44、viceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ X1.1 Approximate Metric Equivalents for Tables 1 and 2Diameters of Wire and Sizes of Mesh Height of Fence Fabricin.mmin.m0.192 4.88 36 9100.148 3.76 42 107048 122060 15201 25 72 1830134 44 84 21302 50 96 2440108 2740120 3050144 3660F1183 96 (2017)4