ASTM E2680-2009e1 Standard Test Method for Appearance of Clear Transparent Liquids (Visual Inspection Procedure)《外观清晰 透明液体(外观检查程序)的标准试验方法》.pdf
《ASTM E2680-2009e1 Standard Test Method for Appearance of Clear Transparent Liquids (Visual Inspection Procedure)《外观清晰 透明液体(外观检查程序)的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM E2680-2009e1 Standard Test Method for Appearance of Clear Transparent Liquids (Visual Inspection Procedure)《外观清晰 透明液体(外观检查程序)的标准试验方法》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: E2680 091Standard Test Method forAppearance of Clear, Transparent Liquids (Visual InspectionProcedure)1This standard is issued under the fixed designation E2680; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year
2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTESection 4 was corrected editorially in December 2011.1. Scope1.1 This test method describes the visual assessment of thea
3、ppearance of clear, transparent liquids for clarity and thepresence of undesirable components (contamination) such assuspended matter, free water (or oil) and particulates whenexamined by transmitted light. Measurements requiring instru-mentation are not included in this method. This test methodwas
4、originally designed for application to glycols and methanolwall washes of marine vessels but may be applicable to otherclear transparent liquids.1.1.1 This method can be used as a field test at storagetemperatures or as a laboratory test at room temperatures.1.1.2 This method provides a rapid pass/f
5、ail test for clarityand contamination of clear, transparent liquids. It is a qualita-tive assessment only.1.2 Review the current appropriate Material Safety DataSheets (MSDS) for detailed information concerning toxicity,first aid procedures, and safety precautions.1.3 The values stated in SI units a
6、re to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practice
7、s and determine the applica-bility of regulatory limitations prior to use. Specific hazardsstatements are given in the section on Hazards, Section 8.2. Referenced Documents2.1 ASTM Standards:2D4176 Test Method for Free Water and Particulate Con-tamination in Distillate Fuels (Visual Inspection Proce
8、-dures)E300 Practice for Sampling Industrial Chemicals3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 appearance, nthe visual perception of a clear, trans-parent liquid.3.1.2 clear and bright (also referred to as clean and bright),na condition in which the liquid is free of ha
9、ze, particulatesor suspended matter particles.3.1.2.1 cleara condition in which the liquid contains novisible contaminants (not more than the maximum allowednumber of suspended matter particles no greater than 1 mm indiameter or particulates of sufficient size to be easily noted).3.1.2.2 brighta con
10、dition in which the liquid is transpar-ent with no haze or visible fee water (or free oil) in organic (oraqueous) liquids.3.1.3 free water (or free oil), nwater or oil in excess tothat soluble in the liquid at ambient temperature which mayappear as haze, cloudiness, droplets or a water or oil layer
11、in anorganic sample.3.1.3.1 DiscussionFor aqueous samples, the determina-tion of free oil is equally important and may have an appear-ance similar to that of free water or oil in organic samples.3.1.4 haze or cloudiness, nis a scatter of light from anaccumulation of tiny suspended particles in the l
12、iquid.3.1.4.1 DiscussionCloudiness is considered synonymouswith haze. Quantification of haze requiring instrumentation isout of the scope of this standard.3.1.5 particulates, nany foreign material in the liquid thatfloats or settles to the bottom of the sample bottle.3.1.5.1 DiscussionThese particul
13、ates may be small solidor semi-solid particles, sometimes referred to as silt or sedi-ment and may be the result of contamination by dust, corro-sion, protective coating deterioration or product instability.3.1.6 suspended matter particles, nany foreign materialthat is in suspension in the liquid (d
14、oes not float or sink) and isinsoluble or separated matter.1This test method is under the jurisdiction of ASTM Committee E15 onIndustrial and Specialty Chemicals and is the direct responsibility of SubcommitteeE15.02 on Product Standards.Current edition approved April 1, 2009. Published April 2009.
15、DOI: 10.1520/E2680-09E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 B
16、arr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.6.1 DiscussionThis usually refers to things like filterfibers, droplets, lint from materials used to dry compartments,prior cargo material or fine pieces of tank or vessel coating.3.1.7 transparent, nliquid is translu
17、cent to transmittedlight.4. Summary of Test Method4.1 An amount of liquid sample at storage or room tempera-ture is visually examined for clarity and presence of contami-nants. The sample is collected in a transparent glass containerand held against a bright, transmitted light to examine forclarity,
18、 suspended matter, haze and the presence of free water(or oil) and subsequently swirled to create a vortex to detect thepresence of particulate matter. For different categories ofglycols, the number of recommended maximum allowed sus-pended matter particles to qualify for a pass is defined. (Table1)
19、. For other clear, transparent liquids, other numbers may bedefined (for example, on the relevant product specifications).5. Significance and Use5.1 This method provides a pass/fail test for appearance ofclear, transparent liquids. Many liquid organic products have aproduct specification requiring t
20、hem to be clear and bright andfree of visible particulate matter and of liquid phases other thanthe main liquid. Producers of these liquid organic productsneed a test method to confirm the quality of their productsmeets product specifications for appearance. Appearance is amanufacturing and sales sp
21、ecification test for ethylene glycolproducts and a loading specification test for methanol wallwashes of marine vessels. This test method was originallydesigned for application to glycols and methanol wall washesof marine vessels, but may be applicable to other clear,transparent liquids. Individuals
22、 using this test method for otherclear transparent liquids should assure themselves that themethod is sufficient for use.5.2 There are many factors that could affect the appearanceduring and after sampling of a liquid product. These factorsmay include transferring of the liquid into a different samp
23、lecontainer, contamination by the sample container or contami-nation by ambient atmosphere. Sampling and evaluation pro-cedures need to be followed to avoid undesirable effects andassure the appearance of the sample is typical for the liquid asmanufactured.6. Interferences6.1 The sample containers m
24、ust be clean and free of dust orother particulates.6.2 If an attempt is made to test the appearance of a liquidthat is darker than a color rating of 5 on the ASTM Color scale(Test Method D4176) or 60 Pt-Co units, the presence of freewater (or oil) or particulates could be obscured and missed bythe a
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTME26802009E1STANDARDTESTMETHODFORAPPEARANCEOFCLEARTRANSPARENTLIQUIDSVISUALINSPECTIONPROCEDURE 外观 清晰

链接地址:http://www.mydoc123.com/p-531684.html