ASTM A989 A989M-2011 Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges Fittings Valves and Parts for High Temperature Service《高温设备用热等静压压制的合金钢法兰 配件 阀门和部件的标准规格.pdf
《ASTM A989 A989M-2011 Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges Fittings Valves and Parts for High Temperature Service《高温设备用热等静压压制的合金钢法兰 配件 阀门和部件的标准规格.pdf》由会员分享,可在线阅读,更多相关《ASTM A989 A989M-2011 Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges Fittings Valves and Parts for High Temperature Service《高温设备用热等静压压制的合金钢法兰 配件 阀门和部件的标准规格.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: A989/A989M 11Standard Specification forHot Isostatically-Pressed Alloy Steel Flanges, Fittings,Valves, and Parts for High Temperature Service1This standard is issued under the fixed designation A989/A989M; the number immediately following the designation indicates the yearof original ad
2、option or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers hot isostatically-pressed, pow-der metallur
3、gy, alloy steel piping components for use inpressure systems. Included are flanges, fittings, valves, andsimilar parts made to specified dimensions or to dimensionalstandards, such as in ASME Specification B16.5.1.2 Several grades of alloy steels are included in thisspecification.1.3 Supplementary r
4、equirements are provided for use whenadditional testing or inspection is desired. These shall applyonly when specified individually by the purchaser in the order.1.4 This specification is expressed in both inch-pound unitsand in SI units. Unless the order specifies the applicable “M”specification de
5、signation (SI units), however, the material shallbe furnished to inch-pound units.1.5 The values stated in either inch-pound units or SI unitsare to be regarded separately as the standard. Within the text,the SI units are shown in parentheses. The values stated in eachsystem are not exact equivalent
6、s; therefore, each system mustbe used independently of the other. Combining values from thetwo systems may result in nonconformance with the specifi-cation.1.6 The following safety hazards caveat pertains only to testmethods portions, 8.1, 8.2, and 9.5-9.7 of this specification:This standard does no
7、t purport to address all of the safetyconcerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety andhealth practices and to determine the applicability of regula-tory limitations prior to use.2. Referenced Documents2.1 ASTM Standar
8、ds:2A275/A275M Practice for Magnetic Particle Examinationof Steel ForgingsA751 Test Methods, Practices, and Terminology for Chemi-cal Analysis of Steel ProductsA961/A961M Specification for Common Requirements forSteel Flanges, Forged Fittings, Valves, and Parts for PipingApplicationsB311 Test Method
9、 for Density of Powder Metallurgy (PM)Materials Containing Less Than Two Percent PorosityE165 Practice for Liquid Penetrant Examination for GeneralIndustryE340 Test Method for Macroetching Metals and AlloysE606 Practice for Strain-Controlled Fatigue Testing2.2 MSS Standard:SP 25 Standard Marking Sys
10、tem for Valves, Fittings,Flanges, and Unions32.3 ASME Specifications and Boiler and Pressure VesselCodes:B16.5 Dimensional Standards for Steel Pipe Flanges andFlanged Fittings42.4 ASME Section IX Welding Qualifications:SFA-5.5 Specification for Low-Alloy Steel Covered Arc-Welding Electrodes43. Termi
11、nology3.1 Definitions of Terms Specific to This Standard:3.1.1 can, nthe container used to encapsulate the powderduring the pressure consolidation process that is removedpartially or fully from the final part.3.1.2 compact, nthe consolidated powder from one canthat may be used to make one or more pa
12、rts.3.1.3 consolidation, nthe bonding of adjacent powderparticles in a compact under pressure by heating to a tempera-ture below the melting point of the powder.3.1.4 fill stem, nthe part of the compact used to fill the canthat is not usually integral to the part produced.1This specification is unde
13、r the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.22 on Steel Forgings and Wrought Fittings for Piping Applications and BoltingMaterials for Piping and Special Purpose Applications.Current edition approved May 1,
14、2011. Published June 2011. Originallyapproved in 1998. Last previous edition approved in 2007 as A989/A989M07.DOI: 10.1520/A0989_A0989M-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume
15、 information, refer to the standards Document Summary page onthe ASTM website.3Available from Manufacturers Standardization Society of the Valve and FittingsIndustry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http:/www.mss-.4Available from American Society of Mechanical Engineers (ASME), ASMEIn
16、ternational Headquarters, Three Park Ave., New York, NY 10016-5990, http:/www.asme.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.5 hot isostatic-pressing, na
17、 process for simultane-ously heating and forming a compact in which the powder iscontained in a sealed formable enclosure, usually made frommetal, and the so-contained powder is subjected to equalpressure from all directions at a temperature high enough topermit plastic deformation and consolidation
18、 of the powderparticles to take place.3.1.6 lot, na number of parts produced from a singlepowder blend following the same manufacturing conditions.3.1.7 part, na single item coming from a compact, eitherprior to or after machining.3.1.8 powder blend, na homogeneous mixture of powderfrom one or more
19、heats of the same grade.3.1.9 rough part, nthe part prior to final machining.4. Ordering Information4.1 It is the responsibility of the purchaser to specify in thepurchase order all requirements that are necessary for materialordered under this specification. Such requirements may in-clude, but are
20、not limited to, the following:4.1.1 Quantity (weight or number of parts).4.1.2 Name of material or UNS number.4.1.3 ASTM designation and year of issue.4.1.4 Dimensions (tolerances and surface finishes).4.1.5 Microstructure examination, if required (5.1.4).4.1.6 Inspection (14.1).4.1.7 Whether rough
21、part or finished machined part (8.2.2).4.1.8 Supplementary requirements, if any.4.1.9 Additional requirements (see 7.2.1 and 16.1).4.1.10 Requirement, if any, that the manufacturer shallsubmit drawings for approval showing the shape of the roughpart before machining and the exact location of test sp
22、ecimenmaterial (see 9.3.1).5. Materials and Manufacture5.1 Manufacturing Practice:5.1.1 Compacts shall be manufactured by placing a singlepowder blend into a can, evacuating the can, and sealing it. Thecan material shall be selected to ensure that it has no deleteri-ous effect on the final product.
23、The entire assembly shall beheated and placed under sufficient pressure for a sufficientperiod of time to ensure that the final consolidated part meetsthe density requirements of 8.1.2.1. One or more parts shall bemachined from a single compact.5.1.2 The powder shall be prealloyed and made by a melt
24、ingmethod capable of producing the specified chemical composi-tion, such as but not limited to air or vacuum induction melting,followed by gas atomization.5.1.3 When powder from more than one heat is used tomake a blend, the heats shall be mixed thoroughly to ensurehomogeneity.5.1.4 The compact shal
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMA989A989M2011STANDARDSPECIFICATIONFORHOTISOSTATICALLYPRESSEDALLOYSTEELFLANGESFITTINGSVALVESANDPARTSFORHIGHTEMPERATURESERVICE

链接地址:http://www.mydoc123.com/p-460258.html