ARMY MIL-PRF-11430 F-1997 CASE MILITARY WATER CAN INSULATED《绝缘军用水箱》.pdf

《ARMY MIL-PRF-11430 F-1997 CASE MILITARY WATER CAN INSULATED《绝缘军用水箱》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-PRF-11430 F-1997 CASE MILITARY WATER CAN INSULATED《绝缘军用水箱》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-PRF-11430F 24 Februarv 199 7 SUPERSEDING MIL-C-11430E 15 November 199 1 PERFORMANCE SPECIFICATION CASE, MILITARY WATER CAN, INSULATED This specification is approved for use by all Departments and Agencies of the Department of Defense (DoD). 1. SCOPE 1.1 Scope. This specification covers the perfo

2、rmance and acceptance requirements for an insulated case for the 5-gallon military water can (see 6.1). 2. APPLICABLE DOCUMENTS - None 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.1.1. 3.2 Operatino reauirem

3、ents. The insulated case shall satis the following user oriented requirements. 3.2 . 1 Color. The insulated case shall be desert tan or olive drab as specified (see 6.2 and 6.5). 3.2.2 Means of carrying. The insulated case shall be designed to provide lifting and carrying by an individual, when used

4、 as intended with the water can. 3.2.3 Accessibilitv to water can. The top (cover) of the insulated case shall provide a seal when closed and be readily opened by an individual wearing arctic mittens. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be use

5、d in improving this document should be addressed to: US. Army Natick Research, Development, and Engineering Center, Attn: SSCNC-WEF, Natick, MA O 1760-501 8 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 7240

6、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF- 1 1430F 1 3.2.4 Safety. The material used for the outer shell and insulation shall be nonflammable and nontoxic. 3.2.5 Insulation of 5-gallon water can. The insulated case shall keep water in

7、a full 5-gallon water can from freezing at temperatures set at -40F for 20 hours. 3.3 Support or ownership reauirements. The insulated case shall meet the following requirements. 3.3.1 Weight. The weight of the insulating case shall be no more than ten pounds. 3.3.2 Thickness. The thickness of the o

8、uter material and insulation used in the case shall not exceed 1 1/2 inches. 3.3.3 Rigid bottom and sides. The bottom of the case shall be made of a rigid material and it shall extend up from the bottom along the front, back and sides for a distance of at least 1 1/2 inches. 3.3.4 Durability. The in

9、sulating case shall withstand the rigors normally exerted by field operations when dropped. 3.3.5 Identification marking. The identification marking shall be located on the inside of the case cover and shall be applied with a marking medium that is well-defined, clearly legible and with characters t

10、hat are approximately 1/4 inch in height. The marking medium shall be durable and compatible with the material used on the inside of the case cover. The following information is required: “CASE, MILITARY WATER CAN, INSULATED; Contract No; Stock No. and Contractors name“. 3.3.5.1 Special marking. The

11、 letters, “US“ shall be permanently placed on the outside of both sides of the case. The letters shall be in block form and shall be at least 1 inch in height, and the marking medium shall be durable and compatible with the material used on the outside of the case. 3.4 Fnvironmental reauirements. Th

12、e insulated case with full 5-gallon water can shall be functional in ambient temperatures from -40F to 125OF. 3.5 Interface and interoperabilie reauirements. The insulating case shall be designed for use with the 5-gallon water can (NSN 7240-00-089-3827 or NSN 7240-01-365-5317). The water can shall

13、fit snugly inside the insulated case. 3.6 Government-loaned equipment The Government shall supply two 5-gallon water cans to be used as a guide to fabricate the insulated case (see 3.5 and 6.7). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 3.2.

14、4 3.2.5 3.3 3.3.1 3.3.2 4.3.4 4.3.5 4.4 4.4.1 4.4.2 MIL-PRF-LL430F 706 2029080 519 = MIL-PW-11430F 4. VERIFICATION 4,l Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.1.1) b. Conformance inspection (see 4.1.2)

15、4.1.1 First article inspection. When a first article inspection is required (see 3.1 and 6.2), a sample shall be examined for all the verifications listed in table I. 4.1.2 Conformance insDection. Conformance inspection includes those examinations and tests from table I as defined in the contract or

16、 purchase order (see 6.4). TABLE I. Verification n Title :thods Requirement 3.2 Verification I OPERATING REQUIREMENTS 4.3 4.3.1 I Coior 3.2.1 3.2.2 4.3.2 Means of carrying Accessibility to water can Safety Insulation of 5-gallon water can 3.2.3 14.3.3 1 SUPPORT OR OWNERSHIP REQUIREMENTS I Weight Thi

17、ckness 3.3.3 4.4.3 Rigid bottom and sides Durability Identification marking Special marking OPERATING REQUIREMENT INTERFACE AND INTEROPERABILITY REOUIREMENTS 3.3.4 4.4.4 4.4.5 3.3.5 4.4.6 3.3.5.1 3.4 4.4.7 3.5 4.4.8 I 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

18、ense from IHS-,-,-MIL-PRF- 1 1430F 4.2 Verification methods. Verification methods can include visual examination, measurement, testing, certification and similarity to previously-approved or previously-qualified designs. 4.2.1 Verification alternatives. The manufacturer may propose alternative test

19、methods, techniques, or equipment, including the application of statistical process control, tool control, or cost-effective sampling procedures to veri performance. See the contract for alternatives that replace verifications required by this specification. 4.3 Operating reauirements verification.

20、All user requirements shall be verified as follows: 4.3.1 Color examination. Visually inspect the insulating case color for similarity to the standard color samples, as specified in the contract or purchase order (see 6.6). 4.3.2 Means of carrying verification. The insulated case shall be visually i

21、nspected to verify that the design is such that an individual can lift or carry the insulated case with the water can inserted. 4.3.3 Accessibility to water can test. A 5-gallon water can shall be inserted in the insulating case and the cover closed. Don a pair of arctic mittens and open the cover t

22、o access the water can. With mittens on, close and seal the cover of the insulating case. Opening and closing of the insulated case cover, with mittens on, shall not exceed 20 seconds for each function. 4.3.4 Safety certification. A certificate shall be provided, verifying that the materials used fo

23、r the outer shell and insulation of the case, do not pose a fire or toxic hazard. 4.3.5 Insulation of 5-gallon water can verification. The insulated case with a full 5-gallon water can inserted, shall be placed in a freezer unit set at - 40F for 20 hours. The starting temperature of the water shall

24、be approximately 50“ F. At the end of 20 hours, remove the insulated case and water can from the freezer and pour the water into gallon containers. At least 4 gallons of water shall be liquid. 4.4 SuDpor or ownershi? reauirements verification. All support or ownership requirements shall be verified

25、as follows: 4.4.1 Weight examination. Verify, by weighing, that the insulated case weighs no more than ten pounds. 4.4.2 Thickness examination. Veri, by measuring, that the outer material and insulation material combined, do not exceed a thickness of 1 1/2 inches. 4 Provided by IHSNot for ResaleNo r

26、eproduction or networking permitted without license from IHS-,-,-MIL-PRF-11430F 4.4.3 Rigid bottom and sides examination. Visually verify and measure that the bottom of the insulating case is made of a rigid material. This material shall extend upward from the bottom along the front, back and sides

27、for a distance of at least 1 1/2 inches. 4.4.4 Durabilitv test. Prepare a platform 4 feet from ground level. Fill the 5-gallon water can and insert into the insulating case and place on the platform. The insulated case shall be dropped 3 times from this height. Remove the water can and visually insp

28、ect the case to verify that the inside and outer materials are not damaged. 4.4.5 Identification markiw inmection. Visually inspect that the required identification marking is complete and accurate. Verify that all markings are legible, well-defined and characters are 1 /4 inch in height. The contra

29、ctor shall certify that the marking medium used is durable. 4.4.6 Suecial markine inwection. Visually inspect that the “US“ marking is on both sides of the outside of the case and the letters are at least 1 inch in block form. The contractor shall certify that the marking medium used is durable. 4.4

30、.7 Environmental requirements certification. The contractor shall certify that the insulated case with full 5-gallon water can is functional at ambient temperatures of - 40F to 125F. 4.4.8 Interface and interoperability requirements examination. Verify, by measwing, that the 5-gallon water can fits

31、snugly inside the insulated case, With the water can inserted inside the case, there shall be no more than 114 inch distance from the outside surface of the water can to the inside surface of the insulation. Measurements shall be taken with the cover open, at top front, top back and top sides. When

32、measuring, the opposite side shall be touching the inside of the insulation, e.g., if measuring the front, the back side of the water can shall be touching the back inside edge of the insulation. Repeat this procedure for measuring back and sides. 5. PACKAGING 5.1 Packaging. For acquisition purposes

33、, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are m

34、aintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products

35、, or by contacting the responsible packaging activitjr. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-11430F 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory). 6.1 I

36、ntended use. The insulated case is primarily for use in cold climates, for the 5-gallon water can to keep water from freezing. The case and 5-gallon water can may also be used for transporting warm food, coffee or other supplies to troops in the field. 6.2 Acquisition requirements. Acquisition docum

37、ents must specie the following: a. Title, number and date of this specification b. When a first article is required (see 3.1,4.1.1 and 6.3) c. Color selection in accordance with 3.2.1 d. Sampling plan for conformance inspection (see 4.1.2) e. Packaging requirements (see 5.1) 6.3 First article. When

38、requiring a first article inspection, contracting documents should provide specific guidance to offerors. This guidance should cover whether the first article is a first article sample, a first production item, or the number of test items. These documents should also include specific instructions re

39、garding arrangements for examinations, approval of first article test results and disposition of first articles, Pre-solicitation documents should provide Government waiver rights for samples for first article inspection to bidders offering a previously- acquired or tested product. Bidders offering

40、such products who wish to rely on such production testing must furnish evidence with the bid that prior Government approval is appropriate for the pending contract. 6.4 Conformance inspection. Affordable conformance inspection with confidence varies depending upon a number of procurement risk factor

41、s. Some of these factors include contractor past performance, government schedules and budget, product material and design maturity, manufacturing capital equipment and processes applied, the controlled uniformity of those processes, labor skills and training, and the uniformity of measuring process

42、es and techniques. During the solicitation, contracting documents should indicate those tests desired fiom table I and their designated frequency based on a risk assessment for the procurement. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PR

43、F-LL430F W 9999906 2029084 Lb4 Color number 1 - Desert Tan 2 - Olive Drab L Specification number Designates a military performance specification MIL-PW-11430F 6.5 Pari or identifjkx number !PIN). The PINS to be used for items acquired by this specification are created as follows: This example descri

44、bes a part numbering system for specification MIL-PRF-11430F. officer. Desert tan shade No. 33446 and olive drab shade No. 34088 are acceptable and can be found in FED-STD-595. 6.6 Standard color samples. Standard color samples are available fi-om the contracting 6.7 Government-loaned eauipment. Con

45、tact the contracting officer for two 5-gallon water cans listed in 3.6. 6.8 Recvcled. recovered or environmentallv preferable materials. Recycled, recovered or environmentally preferable materials should be used to the maximum extent possible, provided the materials meet or exceed the operational, e

46、nvironmental and maintenance requirements specified herein and promote economically advantageous life cycle costs. 6.9 Sub-iect term kev word) listing. Container insulating Cold retention Heat retention 6.1 O Chanees from previous revision. Marginal notations are not used in this revision to identi

47、changes with respect to the previous issue, due to the extensiveness of the changes required to convert this specification from a detail to a performance specification. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-LL430F m 9999906 2029085 OTO m Custodians: Army - GL Navy - YDl Air Force - 99 Review activities: Army - MD1 Navy - MC Air Force - 84 DLA - GS MIL-PRF- 1 1430F Preparing activity: Army - GL (Project 7240-0272) 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-