ANSI ASSE Series16000-2012 Professional Qualifications Standard for the Plumbing Inspector《管道检查员职业资格标准》.pdf

《ANSI ASSE Series16000-2012 Professional Qualifications Standard for the Plumbing Inspector《管道检查员职业资格标准》.pdf》由会员分享，可在线阅读，更多相关《ANSI ASSE Series16000-2012 Professional Qualifications Standard for the Plumbing Inspector《管道检查员职业资格标准》.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、American Society of Sanitary EngineeringProfessional Qualifications Standard for thePlumbing InspectorASSE/IAPMO/ANSI Series 16000ASSE Board Approved: April, 2012ANSI Approved: June, 2012An American National StandardCopyright American Society of Sanitary Engineering Provided by IHS under license wit

2、h ASSE Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright American Society of Sanitary Engineering Provided by IHS under license with ASSE Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASSE/IAPMO/ANSI Series 16000 Profess

3、ional Qualifications Standard iIssued: June, 2012Copyright Information iiiForeword . vProfessional Qualifications Standards Committee . viSeries 16000 Working Group . viiStandard #16010 1Plumbing Inspector 10-1.1 Scope . 110-1.2 Purpose 110-1.3 Limitations 110-1.4 Reference and Industry Standards .

4、110-2.1 General Knowledge . 110-2.2 Product Performance Knowledge 110-2.3 Product Installation Knowledge . 110-2.4 System Knowledge 210-3.1 Minimum Duties Performed 210-3.2 Terminology 210-3.3 Certification of Inspectors . 2Professional Qualifications Standard for the Plumbing InspectorAppendix A 3A

5、-1 Reference and Industry Standards and Codes 3A-2 Abbreviations and Standards Development Organizations . 19Appendix B 20Vocabulary and DefinitionsTable of ConTenTSCopyright American Society of Sanitary Engineering Provided by IHS under license with ASSE Not for ResaleNo reproduction or networking

6、permitted without license from IHS-,-,-ii ASSE/IAPMO/ANSI Series 16000 Professional Qualifications StandardIssued: June, 2012Copyright American Society of Sanitary Engineering Provided by IHS under license with ASSE Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-A

7、SSE/IAPMO/ANSI Series 16000 Professional Qualifications Standard iiiIssued: June, 2012Professional Qualifications Standard for the Plumbing InspectorAmerican Society of Sanitary EngineeringWestlake, OhioCopyright 2012All rights reserved.CoPYRIGHT InfoRMaTIonNeither this standard, nor any portion the

8、reof, may be reproduced without the written consent of the American Society of Sanitary Engineering. Organizations wishing to adopt or list any ASSE Standard should print the ASSE Standard number on the cover page first and in equal or larger type to that of the adopting or listing organization.Copy

9、right American Society of Sanitary Engineering Provided by IHS under license with ASSE Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-iv ASSE/IAPMO/ANSI Series 16000 Professional Qualifications StandardIssued: June, 2012Copyright American Society of Sanitary Engin

10、eering Provided by IHS under license with ASSE Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASSE/IAPMO/ANSI Series 16000 Professional Qualifications Standard vIssued: June, 2012Professional Qualifications Standard for the Plumbing InspectorfoReWoRdThis foreword

11、shall not be considered part of the standard; however, it is offered to provide background information.In 1987, the American Society of Sanitary Engineerings Board of Directors recognized the need to develop Professional Qualifications Standards for the plumbing and mechanical industry. Since that t

12、ime, ASSE has developed a number of Professional Qualifications Standards, including the Series 5000, Cross-Connection Control Professional Qualifications Standard, and the Series 6000, Professional Qualifications Standard for Medical Gas Systems Personnel. Both of these important documents, now eac

13、h considered the industry standard, were necessary to allow the Authority Having Jurisdiction to have nationally recognized standards, developed in an open consensus process by all industry stakeholders, to use in ensuring that individuals working on these critically important systems possess the kn

14、owledge and experience required to successfully perform the installation, testing, maintenance and inspection needed within our industry.With the development of the ASSE/IAPMO/ANSI Series 16000, Professional Qualifications Standard for the Plumbing Inspector, and its companion document, the ASSE Ser

15、ies 17000, Professional Qualifications Standard for the Mechanical Inspector, the Society is again leading the way and raising the bar for the plumbing and mechanical industry. For the first time, these important new standards spell out the experience, education, training and general knowledge requi

16、rements for the inspectors who play a critical role in protecting the health and safety of both the general public and the industry itself.Our ever changing industry is affected by innovation with the constant development of new materials, systems and installation methods. The economy also plays a l

17、arge role in funding for the education of public inspectors and the move toward third-party and multi-craft inspectors. With these industry developments, it was essential that a national standard for plumbing inspectors be developed. That need has been fulfilled with the ASSE 16000.Recognition is ma

18、de of the time volunteered by members of the working group and of the industry members who participated in the development of this standard.Compliance with this standard does not imply acceptance by any code body or Authority Having Jurisdiction.This voluntary consensus standard was promulgated in a

19、ccordance with procedures developed by the American National Standards Institute (ANSI).Copyright American Society of Sanitary Engineering Provided by IHS under license with ASSE Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-vi ASSE/IAPMO/ANSI Series 16000 Profes

20、sional Qualifications StandardIssued: June, 2012donald Summers, Jr., ChairmanUA Local 562St. Louis, MissouriSean ClearyIAPMOScranton, Pennsylvanialaurence T. ColemanUA Local 597Mokena, Illinois dana ColomboNational Inspection Testing and demonstrate knowledge of the following components:a. Appliance

21、s and plumbing appurtenancesb. Backflow prevention devices and assembliesc. Fixtures and faucetsd. Grease interceptorse. Hangers and supportsf. Industrial interceptors (clarifiers) and separatorsg. Piping materialsh. Pumpsi. Traps j. Valvesk. Water heaters and safety components10-2.3 Product Install

22、ation Knowledge10-2.3.1 The Inspector shall be able to describe the proper installation requirements for the plumbing systems pertaining to:Copyright American Society of Sanitary Engineering Provided by IHS under license with ASSE Not for ResaleNo reproduction or networking permitted without license

23、 from IHS-,-,-2 ASSE/IAPMO/ANSI Series 16000 Professional Qualifications StandardIssued: June, 2012a. Applicable governmental requirementsb. Applicable plumbing codes and standardsc. Manufacturers installation instructions10-2.4 System Knowledge 10-2.4.1 The Inspector shall be able to identify and d

24、escribe the appropriate installation of the following:a. Drain waste and vent systemsb. Fixtures, appliances and plumbing appurte-nancesc. Fuel gas piping systemsd. Non-potable water reuse systemse. Private on-site waste systemsf. Private supply, water service and distribution systemsg. Roof and sto

25、rm drainage systemsh. Sanitary drainage systemsi. Water heating systems10-2.4.2 The Inspector shall be able to describe the precautions and hazards associated with the following:a. Chemical wasteb. Cross-connectionsc. Hangers and supportsd. Job site safetye. Non-potable water f. Pipe joiningg. Pipe

26、locationh. Pipe sizingi. Water hammer10-2.4.3 The Inspector shall be able to demonstrate knowledge of the following:a. Adequate water supply b. Administrative proceduresc. Commonly used plan symbolsd. Cross-connection controle. Fuel gas systemsf. Impact of additional plumbing fixtures, systems, plum

27、bing appurtenances and appliancesg. Job site safety requirementsh. On-site waste and water treatmenti. Private on-site wastewater systemsj. Proper installation for plumbing systemsk. Proper testing proceduresl. Wells as water supply10-2.4.4 The Inspector shall be able to identify the correct physica

28、l locations for the following items:a. Backflow prevention assemblies and devicesb. Drain waste and vent systemsc. Fixtures, appliances and plumbing appurtenancesd. Fuel gas piping systemse. Grease interceptorsf. Industrial interceptors (clarifiers) and separatorsg. Non-potable water reuse systemsh.

29、 Piping and valvesi. Plumbing fixture rough-in specificationsj. Pressure reducing valvesk. Roof and storm drainage systemsl. Safety relief valvesm. Sanitary drainage systemsn. Thermal expansion controlo. Trapsp. Water distribution systemsq. Water hammer arrestersr. Water service10-3.1 Minimum duties

30、 PerformedThe Inspector shall be able to perform the following:a. Document inspections and maintain recordsb. Final inspectionc. Fuel gas inspectiond. Read and interpret construction plans e. Rough inspectionf. Underground inspection10-3.2 TerminologyThe Inspector shall be able to demonstrate compre

31、hension of all terminology listed in the ASSE Series 16000 and its appendices.10-3. 3 Certification of Inspectors 10-3.3.1 eligibility requirements10-3.3.1.1 A minimum of five (5) years of documented practical experience in either installation or inspection of plumbing systems. 10-3.3.1.2 Successful

32、 completion of a minimum 36 hour training course encompassing all aspects of ASSE Standard 16010. 10-3.3.1.3 Certification shall include successfully passing a written exam encompassing aspects of ASSE Standard 16010. 10-3.3.1.4 Certification to this standard shall be through a nationally recognized

33、 third-party certification agency. 10-3.3.1.5 Certification shall be for a three (3) year period. 10-3.3.2 Recertification of Inspectors 10-3.3.2.1 Recertification shall include the successful completion of a minimum of 1.5 industry-related Continuing Education Units (15 hours); or an 8 hour course

34、encompassing all aspects of ASSE Standard 16010 and a written examination through a nationally recognized third-party certification agency.Copyright American Society of Sanitary Engineering Provided by IHS under license with ASSE Not for ResaleNo reproduction or networking permitted without license

35、from IHS-,-,-ASSE/IAPMO/ANSI Series 16000 Professional Qualifications Standard 3Issued: June, 2012a-1 Reference and Industry Standards and CodesThe following list of reference and industry standards and codes is part of the requirements of ASSE Standard 16010.AHAM DW-1-2010* Household Electric Dishw

36、ashersAHAM FWD-1-2009* Food Waste Disposers APSP 1-2003* Public Swimming PoolsASCE 25-2006* Earthquake-Actuated Automatic Gas Shutoff Devices ASHRAE 90.1-2010* Energy Standard for Buildings Except Low-Rise Residential Buildings ASME A13.1-2007* Scheme for the Identification of Piping Systems ASME A1

37、12.1.2-2004* Air Gaps in Plumbing Systems (For Plumbing Fixtures and Water-Connected Receptors) ASME A112.1.3-2000 (R2010)* Air Gap Fittings for Use with Plumbing Fixtures, Appliances, and Appurtenances ASME A112.3.1-2007* Stainless Steel Drainage Systems for Sanitary DWV, Storm, and Vacuum Applicat

38、ions, Above- and Below Ground ASME A112.3.4-2000 (R2004)* Macerating Toilet Systems and Related Components ASME A112.4.1-2009* Water Heater Relief Valve Drain Tubes ASME A112.4.2-2009* Water Closet Personal Hygiene Devices ASME A112.4.3-1999 (R2010)* Plastic Fittings for Connecting Water Closets to

39、the Sanitary Drainage System ASME A112.4.14-2004 (R2010) Manually Operated, Quarter-Turn Shutoff Valves for Use in Plumbing Systems ASME A112.6.1M-1997 (R2008) Floor-Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use ASME A112.6.2-2000 (R2010)* Framing-Affixed Supports for Off-the-F

40、loor Water Closets with Concealed TanksASME A112.6.3-2001 (R2007)* Floor and Trench Drains ASME A112.6.4-2003 (R2008)* Roof, Deck, and Balcony Drains ASME A112.6.7-2010* Sanitary Floor Sinks ASME A112.6.9-2005 (R2010)* Siphonic Roof Drains ASME A112.14.1-2003 (R2008)* Backwater Valves ASME A112.14.3

41、-2000 (R2004)* Grease Interceptors ASME A112.14.4-2001 (R2007)* Grease Removal Devices ASME A112.14.6-2010* FOG (Fats, Oils, and Greases) Disposal Systems ASME A112.18.1-2005/CSA B125.1-2005 Plumbing Supply Fittings ASME A112.18.2-2005/CSA B125.2-2005 Plumbing Waste Fittings ASME A112.18.3-2002 (R20

42、08)* Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings ASME A112.18.6-2009/CSA B125.6-2009* Flexible Water Connectors aSSe SeRIeS 16000 aPPendIX aReference and Industry Standards and CodesCopyright American Society of Sanitary Engineering Provided by I

43、HS under license with ASSE Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 ASSE/IAPMO/ANSI Series 16000 Professional Qualifications StandardIssued: June, 2012ASME A112.18.7-1999 (R2004)* Deck Mounted Bath/Shower Transfer Valves with Integral Backflow Protection A

44、SME A112.18.9-2011* Protectors/Insulators for Exposed Waste and Supplies on Accessible FixturesASME A112.19.1-2008/CSA B45.2-2008* Enamelled Cast Iron and Enamelled Steel Plumbing FixturesASME A112.19.2-2008/CSA B45.1-2008* Ceramic Plumbing FixturesASME A112.19.3-2008/CSA B45.4-2008* Stainless Steel

45、 Plumbing Fixtures ASME A112.19.5-2005* Trim for Water-Closet Bowls, Tanks, and Urinals ASME A112.19.7-2006* Hydromassage Bathtub Appliances ASME A112.19.10-2003 (R2008)* Dual Flush Devices for Water Closets ASME A112.19.12-2006 (R2011)* Wall Mounted, Pedestal Mounted, Adjustable, Elevating, Tilting

46、, and Pivoting Lavatory, Sink, and Shampoo Bowl Carrier Systems and Drainage Waste SystemsASME A112.19.14-2006 (R2011)* Six-Liter Water Closets Equipped with a Dual Flushing Device ASME A112.19.15-2005 (R2010)* Bathtubs/Whirlpool Bathtubs with Pressure Sealed DoorsASME A112.19.19-2006 (R2011)* Vitre

47、ous China Nonwater Urinals ASME A112.21.3M-1985 (R2007)* Hydrants for Utility and Maintenance Use ASME A112.36.2M-1991 (R2008)* Cleanouts ASME B1.20.1-1983 (R2006)* Pipe Threads, General Purpose, Inch ASME B1.20.3-1976 (R2008)* Dryseal Pipe Threads, Inch ASME B16.1-2010* Gray Iron Pipe Flanges and F

48、langed Fittings: Classes 25, 125, and 250ASME B16.3-2006* Malleable Iron Threaded Fittings: Classes 150 and 300ASME B16.4-2006* Gray Iron Threaded Fittings (Classes 125 and 250) ASME B16.5-2009* Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch ASME B16.12-2009* Cast Iron Threaded Drainage Fittings ASME B16.15-2006* Cast Copper Alloy Threaded Fittings: Classes 125 and 250 ASME B16.18-2001 (R2005)* Cast Copper Alloy Solder Joint Pressure Fittings ASME B16.20-2007* Metallic Gaskets For Pipe Flanges: Ring-Joint, Spiral-Wound, and Jacketed ASME B16.21-2005* Nonmetallic Fla