AECMA PREN 2667-1-1996 Aerospace Series Non-Metallic Materials Foaming Structural Adhesives Test Methods Part 1 Tensile Single-Lap Shear Edition P 1《航天系列包括非金属材料发泡结构胶粘剂的测试方法.第1部分 拉伸.pdf

《AECMA PREN 2667-1-1996 Aerospace Series Non-Metallic Materials Foaming Structural Adhesives Test Methods Part 1 Tensile Single-Lap Shear Edition P 1《航天系列包括非金属材料发泡结构胶粘剂的测试方法.第1部分 拉伸.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 2667-1-1996 Aerospace Series Non-Metallic Materials Foaming Structural Adhesives Test Methods Part 1 Tensile Single-Lap Shear Edition P 1《航天系列包括非金属材料发泡结构胶粘剂的测试方法.第1部分 拉伸.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、STD-AECMA PREN 2bb7-1-ENGL 177b LOL23LL OOL2L22 55T Edition approved for publication 1996-1 1-29 AECMA STANDARD NORME AECMA AECMA NORM Comments should be sent within six months after the date of publication to AECMA Guiledelie 94 B-1200 BRUXELLES prEN 2667-1 Edition P 1 November 1996 PUBLISHED BY TH

2、E EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Guiledelie 94 - 8-1200 BRUXELLES - Tel. (32) 2 775 81 10 - Fax. (32) 2 775 81 11 ICs : Descriptors : ENGLISH VERSION Aerospace series Non-metallic materials Foaming structural adhesives Test methods Part 1 : Tensile single-lap shear Srie arospat

3、iale Luft- und Raumfahrt Matriaux non-mtalliques Nichtmetallische Werkstoffe Adhsifs structuraux expansibles Strukturelle Expansionsklebstoffe Mthodes dessai Prfverfahren en traction im Zugversuch Partie 1 : Cisaillement recouvrement simple Teil 1 : Einfach berlappte Scherprobe This “Aerospace Serie

4、s“ Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member c

5、ountries. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre INPSI

6、 and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. Nota - Extra copies can be supplied by B.N.A.E. - Technopolis 54 - 199, rue Jean-Jacaues Rousseau - 921 38 ISSY-LE

7、S-MOULINEAUX CEDEX C7 Chairman Mr Wright I I aecma 1991 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-AECMA PREN 2bb7-1-ENGL 177b LOL23L1 0012123

8、 47b W Page 3 prEN 2667-1 : 1996 1 Scope This standard defines the test method for determining the bond strength of structural foaming adhesive films or pastes by means of tensile single-lap shear specimens. This test method is suitable for comparative tests regarding the quality of a foaming adhesi

9、ve when thickness is taken into account, in order to obtain maximum mechanical characteristics in relation to the expansion ratio. It preferably applies to low expansion ratios, .e. I 50 % measured according to the method EN 2667-3. For higher expansion ratios, .e. 50 %, the tube test EN 2667-2 is p

10、referred. 2 Normative references IS0 7500-1 EN 2088 EN 2090 EN 2334 EN 2497 EN 2538 EN 2667-2 EN 2667-3 EN 3456 Metallic materials - Verification of static uniaxial testing machines - Part 1 : Tensile testing machines Aerospace series - Aluminium alloy 2014A-T4 or T42 - Clad sheets and strips - 0,4

11、mm I a I 6 mm l) Aerospace series - Aluminium alloy 2024-T3 - Clad sheet and strip - 0,4 mm I a I 6 mm Aerospace series - Acid chromate pickling of aluminium and aluminium alloys Aerospace series - Dry abrasive blasting of titanium and titanium alloys Aerospace series - Steel FE-PM-61 - Solution ann

12、ealed and precipitation hardened - 1 240 MPa I R, I 1 310 MPa sheet a I 10 mm 2, Aerospace series - Non-metallic materials - Foaming structural adhesives - Test methods - Part 2 : Compressive tube shear 2, Aerospace series - Non-metallic materials - Foaming structural adhesive films - Test methods -

13、 Part 3 : Expansion ratio and volatile content 2, Aerospace series - Titanium alloy TLP64001 - Annealed - Sheet and strip, hot rolled a I6 mm2) 3 Apparatus and auxiliary equipment 3. I Tensile testing machine The test machine shall be approved to IS0 7500-1 and so designed that the breaking load lie

14、s between 10 % and 90 % of the selected full-scale capacity. The loads shall be recorded to an accuracy of 1 %. 1) Published as AECMA Standard at the date of publication of this standard 2) Published as AECMA Prestandard at the date of publication of this standard Previous page is blank Copyright As

15、sociation Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- STD-AECMA PREN 2bb7-L-ENGL 177b LO12311 OOL2124 322 m Page 4 prEN 2667-1 : 1996 3.2 Auxiliary equipment Air circul

16、ating oven with an accuracy of f 5 OC. Heating press with an accuracy of f 3 OC. Autoclave with an accuracy of k 5 OC. Band saw. Thermqelectric couple. 4 Test panels, test specimens 4.1 Test panels The shape and the dimensions of the panels shall be in conformity with figure 1 or figure 2. Precut te

17、st panel according to figure 2 shall preferably be used for titanium alloy and steel materials described in 4.1.1. 4.1 .l Materials The following materials are normally to be used : or aluminium alloy 2024-T3 in accordance with EN 2090 aluminium alloy 2014A-T4 or T42, in accordance with EN 2088. At

18、test temperatures exceeding 150 OC, one of the following materials shall be used : corrosion resisting steel FE-PM-61, in accordance with EN 2538 titanium alloy TI-P64001, in accordance with EN 3456. 4.1.2 Surface preparation Surface preparation before bonding shall be in accordance with EN 2334 for

19、 aluminium alloys or with EN 2497 for titanium, unless otherwise specified in the material standard. Surface preparation for steel shall be specified in the material standard. 4.1.3 Bonding Bonding of the test panels shall take place within 4 h after completion of the preliminary treatment. Otherwis

20、e, the treated surfaces of the test panels shall be coated with a protective primer. The bond thickness a, (see figure 4) of the cured foaming adhesive shall be 40 % to 50 % smaller than the final thickness after free expansion as determined in accordance with EN 2667-3. Conformance with the bond th

21、ickness to be achieved shall be ensured by the insertion of a suitable spacer made according to figure 3. The spacer avoids the flection of the upper jig due to pressure and shall be coated with release agent before use to avoid adhesion on spacer. The application of the foaming adhesive system (adh

22、esive and primer, if necessary) as well as the curing shall be carried out in accordance with the adhesive manufacturer?s instructions and the material standard. An adhesive strip of (12,5 i 0,5) mm width shall be applied to the lower test panel. The assembly shall then be completed with the spacer

23、and the upper test panel. Curing shall be carried out in an air circulating oven, autoclave or heating press. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from I

24、HS-,-,-Page 5 prEN 2667-1 : 1996 4.1.4 The final test panels shall be conditioned and tested after a storage period of at least 16 h after curing and under the following conditions. Storage of test panels after curing - temperature : (23 * 2) OC - relative humidity : (50 5) % 4.2 Test specimens 4.2.

25、1 Cutting test specimens The cutting of the test panels into test specimens shall be done with an appropriate tool such as a band saw, in accordance with figures 4 and 5. The number of teeth and the set of the saw, as well as the feed and cutting speed shall be chosen so to minimize thermal and mech

26、anical stressing. The cuts shall be straight, parallel and perpendicular to the two edges. To cut out test panels no cooling fluid shall be used. The cut edges shall be deburred with a fine file or abrasive paper. Excess adhesive is not to be removed. Each test specimen shall be identified with an i

27、ndividual reference mark so as to locate the number of the test panel from which it originated as well as its position on this panel. 4.2.2 Quantity There shall be a minimum of five individual test specimens for each test. 5 Procedure Tests shall be performed at the temperatures specified in the mat

28、erial standard. If the test temperature differs from the ambient temperature, the heat-up rate or the cooling rate of the test specimen shall be less than 10 OC/min. For all tests carried out at a temperature other than ambient, load shall be applied after stabilization at the specified temperature

29、for a minimum of 10 min and a maximum of 30 min (unless otherwise specified by the supplier). For all temperatures with the exception of the ambient temperature, control of the temperature of the test specimen is carried out by means of a thermoelectric couple fixed into the test specimen, in accord

30、ance with figure 6. Any misalignment of the specimen configuration during clamping into the tensile testing machine shall be compensated by suitable means e.g. by interposed blocks at each end of the test piece (see figure 5). The test piece shall be held between the jaws at (50 L W The dimensions L

31、 and W shall be measured, before applying the load, to within * 0,l mm. is the bond strength, in megapascals ; is the length of overlap, in millimetres ; is the width of overlap, in millimetres. 6.2 Determination of failure mode The failure pattern shall differentiate between adhesive and cohesive p

32、ortions. They shall be expressed as a percentage of the total area. Where a primer has been used, the plane of any adhesive failure is to be given. 7 Designation EXAMPLE EN2667- 1 I Number of this standard I 8 Test report It shall include the following : - reference to this standard ; - complete ide

33、ntification of the foaming adhesive and of the primer, if any, including the type, name and address of the manufacturer, batch number, material standard number, initial thickness and expansion ratio to EN 2667-3 ; - storage conditions of adhesive before curing ; - complete identification of the meta

34、l including the thickness in millimetres and its surface preparation, including storage up to the bonding ; - processing and curing conditions including the choice of bonding method (autoclave, press or furnace), pressure on the adhesive bond, heat-up rate, curing time and temperature ; - test condi

35、tions and temperature ; - type of test machine, selected capacity, and rate of load application ; - number of test specimens ; - information regarding each test specimen including reference mark, dimensions of the overlaps, panel thickness, thickness of the adhesive after curing, failure load and bo

36、nd strength ; - the type of failure, including the average break, in cohesion and/or adhesion for the adhesive and any primer as a percentage of the total overlap surface ; - the average, minimum and maximum bond strength values, as well as the standard deviation of the test series ; - any deviation

37、 from this standard in detail ; - date of teS.and signature. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD.AECMA PREN 2bb7-3-ENGL L77b 3O323Ll O0

38、32327 031 Page 7 prEN 2667-1 : 1996 Dimensions in millimetres Test specimens C F C .- E Cylindrical hole / Oblono hole 10 c- 25 i 0.2 - Figure 1 : Test panel to be machined Test soecimens I m 0 F c E - .- 10 c- 25+0.2- 1 1 - 1.5 to 2 Figure 2 : Pre-cut test panel Copyright Association Europeene des

39、Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 8 prEN 2667-1 : 1996 CI I I Adhesive spew m Il Dimensions in millimetres c L O a a -7 cn W Ln a m II II Figure 3 : Position of spacer

40、I I I , 1 I 2 I I I +I In N II 1 Rolling 11 direction I min. 170 I a, = thickness of cured adhesive a = thickness of test piece 1,6 mrn for aluminium alloy 1.2 mrn for steel and titanium Figure 4 : Test specimens after curing Copyright Association Europeene des Constructeurs de Materiel Aerospatial

41、Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 9 prEN 2667-1 : 1996 Dimensions in millimetres Block 50 5 L = 12.5 f 0,3 50 f 5 c - Block thickness : / Adhesive spew thickness : UC+U Figure 5 : Test specimens after curin

42、g with alignment blocks QI Thermoelectric couple Figure 6 : Position of thermoelectric couple Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 10 prEN 2667-1 : 1996 Dimensions in millimetres Figure 7 : Position in jaws of tensile test machine Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-