UL 2034 CRD-2014 UL Standard for Safety Single and Multiple Station Carbon Monoxide Alarms - Section Paragraph Reference Align the Drop Test requirements with the requirements spe.pdf

《UL 2034 CRD-2014 UL Standard for Safety Single and Multiple Station Carbon Monoxide Alarms - Section Paragraph Reference Align the Drop Test requirements with the requirements spe.pdf》由会员分享，可在线阅读，更多相关《UL 2034 CRD-2014 UL Standard for Safety Single and Multiple Station Carbon Monoxide Alarms - Section Paragraph Reference Align the Drop Test requirements with the requirements spe.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUNDERWRITERS LABORATORIES INC. CERTIFICATION REQUIREMENT DECISIONThis Certification Requirement Decision is prepared and published by Underwriters Laboratories Inc.(UL). It is normative for the a

2、pplicable UL Product Certification Program(s); however, it is currently notpart of the UL Standard(s) referenced below.Product Category (CCN): CZHF, JMAE, CZHF2Standard Number: UL 2034Standard Title: Standard for Single and Multiple Station Carbon Monoxide AlarmsEdition Date: February 28, 2008Editio

3、n Number: 33.26 (New), 3.27 (New), 69 (Revised)Section / Paragraph Reference: Align the Drop Test requirements with therequirements specified in UL 2075.Subject:DECISION:New Section 3.263.26 Tabletop Alarm or Accessory An alarm or accessory intended for resting on a horizontal surface,such as a tabl

4、e or nightstand.New Section 3.273.27 Portable Alarm or Accessory An alarm or accessory intended for transient use, such as a travel orpersonal alarm.Revised Section 69.69 Drop Test69.1 This test is to be conducted only on portable or tabletop alarms or accessories intended for transientuse, such as

5、a travel alarm, and is not to be conducted on alarms intended for stationary installation.69.2 An portable alarm or accessory shall withstand five drops from a height of 7 feet (2.1 m) onto a tiledconcrete floor without exposure of internal hazardous-voltage parts or affecting its intended operation

6、 andsensitivity. The sample is to be held so that each impact with the floor is at a different location on thealarm. Parts shall not become dislodged unless the dislodged part does not affect operation or sensitivityof the unit, the dislodged part is replaceable (such as a cover), there are no hazar

7、dous-voltage partsexposed, and the condition is visually obvious.69.3 A tabletop alarm or accessory shall be dropped from the maximum height limit specified in the usersmanual. At a minimum the unit shall be dropped from a height of 3.28 feet (1 meter).69.3 69.4 Each of two alarms is to be raised to

8、 a the applicable height of 7 feet (2.1 m) specified in 69.2and 69.3, and be permitted to drop five times onto a concrete floor covered with a 1/8 inch (3.2 mm) thickuncushioned vinyl tile. Following the drops, the unit is to be examined for damage and tested forsensitivity. Sensitivity measurements

9、 recorded after the drop test shall comply with 39.1.1.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULRATIONALE FOR DECISION:The intent of this CRD is to align the drop test performance requirements for carbon monoxide alarms withcurrent test

10、 practices based on the intended application of the product. The current drop distance of 7 feetwas established with the assumption that portable alarms would be mounted to the tops of doors, whichare typically no more than 7 feet high. If the alarm is not intended to be located on a door, but inste

11、ad ona nightstand, desk or the like, the 7 foot height was not considered to be consistent with the intendedapplication of the alarm and a 1 meter (3.28 feet) drop height was established as normative certificationpractice.Copyright 2014 Underwriters Laboratories Inc.UL, in performing its functions i

12、n accordance with its objectives, does not guarantee or warrant thecorrectness of Certification Requirement Decisions it may issue or that they will be recognized or adoptedby anyone. Certification Requirement Decisions are the opinion of Underwriters Laboratories Inc. inpractically applying the req

13、uirements of the standard. They do not represent formal interpretations of thestandard under American National Standards Institute (ANSI) processes. UL shall not be responsible toanyone for the use of or reliance upon Certification Requirement Decisions by anyone. UL shall not incurany obligation or

14、 liability for damages, including consequential damages, arising out of or in connectionwith the use or reliance upon Certification Requirement Decisions. The electronic version of theCertification Requirement Decision is the current version and previously printed copies may be outdated.This document is published as a service to ULs certification customersSTANDARD NUMBER: UL 2034 -2-