SAE J 119-2010 Fiberboard Crease Bending Test《纤维板褶皱弯曲试验》.pdf
《SAE J 119-2010 Fiberboard Crease Bending Test《纤维板褶皱弯曲试验》.pdf》由会员分享,可在线阅读,更多相关《SAE J 119-2010 Fiberboard Crease Bending Test《纤维板褶皱弯曲试验》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication m
3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside U
4、SA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/J119_201005SURFACEVEHICLESTANDARDJ119 MAY2010 Issued 1969-09 Reaffirmed 2010-05 Superseding J11
5、9 JUL2005 Fiberboard Crease Bending Test RATIONALE Five year review - Reaffirm as is. 1. SCOPE This test method is designed to determine the suitability of a painted or unpainted fiberboard for application involving creasing and bending. The specific purpose of the test is to determine whether a giv
6、en material, properly creased, can be bent along the impressed crease without objectionable failure on the surface of the bend. 2. REFERENCES 2.1 Applicable Publication The following publication forms a part of the specification to the extent specified herein. Unless otherwise indicated the latest r
7、evision of SAE publications shall apply. 2.1.1 SAE Publication Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001. SAE J315 Fiberboard Test Procedure 3. EQUIPMENT REQUIRED 3.1 Press with adequate tonnage to crease the test specimen to the desired configuration. 3.2 Matched male an
8、d female die sections, selected for the caliper of sample to be tested and for the desired end result (see Section 5).4. TEST SPECIMEN 4.1 Size Minimum of 100 x 300 mm or as determined by the size of the test die. 4.2 Condition Prior to Testing See SAE J315 (see Section 4) unless otherwise specified
9、. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHSSAE J119 Reaffirmed MAY2010 Page 2 of 45. CREASING RULE (MALE DIE SECTION) 5.1 The thickness of the creasing rule (T2) is designated commercially by the p
10、rinters point system (1 point equals approximately 0.36 mm), Figure 1.FIGURE 1 - CREASING RULE (MALE DIE SECTION) 5.2 Commercially available in either flat or round face and in the following thicknesses (round face rule shall be used unless otherwise specified):TABLE 1 - CREASING RULE THICKNESS Stan
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEJ1192010FIBERBOARDCREASEBENDINGTEST 纤维板 褶皱 弯曲 试验 PDF

链接地址:http://www.mydoc123.com/p-1026173.html