SAE AS 95234 1-2013 CONNECTOR RECEPTACLE BAYONET COUPLING IN LINE《联机连接器插座卡口式联结器》.pdf

《SAE AS 95234 1-2013 CONNECTOR RECEPTACLE BAYONET COUPLING IN LINE《联机连接器插座卡口式联结器》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 95234 1-2013 CONNECTOR RECEPTACLE BAYONET COUPLING IN LINE《联机连接器插座卡口式联结器》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CONNECTOR RECEPTACLE, BAYONET COUPLING, IN LINE AS95234/1Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording,

2、 or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2013-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/

3、AE-8C1 FEDERAL SUPPLY CLASS 5970 AS95234/1SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS95234SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirely voluntary, and its applicability and suit

4、ability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibility ofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised,orcancelled.SAE invites yourwrittencomments andsuggestions. SAE values your input

5、. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS95234/1 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO STANDARDIZE COMMERCIAL CONNECTORS FOR USER APPLICATIONS. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SH

6、ALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS95234. FIGURE 1 - CONNECTOR RECEPTACLE AEROSPACE STANDARD AS95234/1SHEET 2 OF 2 CONNECTOR RECEPTACLE, BAYONET COUPLING, IN LINE TABLE 1 - FIGURE 1 DIMENSIONS SHELL SIZE FRONT VIEW SIDE VIEW Q MAX. A +.000/-.006 (+0.00/-0.15) H THREAD CLASS 2A K

7、.008 (0.2) L MAX. M +.016/-.000 (+0.4/-0.00 10SL .886 (22.5) .717 (18.2) .625-24 UNEF .110 (2.8) 1.570 (39.9) .559 (14.2) 14S 1.161 (29.5) .969 (24.6) .875-20 UNEF .126 (3.2) 1.570 (39.9) .559 (14.2) 16S 1.240 (31.5) 1.079 (27.4) 1.000-20 UNEF .126 (3.2) 1.570 (39.9) .559 (14.2) 16 1.240 (31.5) 1.07

8、9 (27.4) 1.000-20 UNEF .126 (3.2) 1.850 (47.0) .748 (19.0) 18 1.358 (34.5) 1.213 (30.8) 1.0625-18 UNEF .157 (4.0) 1.850 (47.0) .748 (19.0) 20 1.476 (37.5) 1.346 (34.2) 1.1875-18 UNF .157 (4.0) 1.850 (47.0) .748 (19.0) 22 1.594 (40.5) 1.472 (37.4) 1.3125-18 UNEF .157 (4.0) 1.850 (47.0) .748 (19.0) 24

9、 1.752 (44.5) 1.610 (40.9) 1.4375-18 UNEF .157 (4.0) 1.850 (47.0) .811 (20.6) 28 1.969 (50.0) 1.839 (46.7) 1.750-18 UNS .157 (4.0) 2.100 (53.3) .811 (20.6) 32 2.224 (56.5) 2.102 (53.4) 2.000-18 UNS .157 (4.0) 2.100 (53.3) .874 (22.2) 36 2.480 (63.0) 2.346 (59.6) 2.250-16 UN .157 (4.0) 2.100 (53.3) .

10、874 (22.2) REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS95234. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WTH FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS ARE GIVEN FOR INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM

11、. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016. 2. FOR INSERT ARRANGEMENTS, SEE AS95234, APPENDIX B. 3. PART NUMBER: THE PART NUMBER SHALL BE AS SHOWN IN THE EXAMPLE BELOW: AS95234 /1 W 16 - A11 P X BASIC SPECIFICATION DETAIL SHEET FINISH AND TEMPERATURE RATING SHELL SIZE (SEE AS95234 APPENDIX A)

12、 INSERT ARRANGEMENT (SEE AS95234 APPENDIX B) CONTACT DESIGNATION AND MATERIAL (SEE AS95234) INSERT POSITION (W, X, Y, Z) LEAVE BLANK FOR NORMAL SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDIT

13、ORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.