SAE AS 6043A-2012 FITTING TEE STANDARD AND REDUCER BULKHEAD ON RUN FLARELESS PRECISION TYPE《精密型无间隙 标准和减径管 在使用中的闷头三通配件》.pdf

《SAE AS 6043A-2012 FITTING TEE STANDARD AND REDUCER BULKHEAD ON RUN FLARELESS PRECISION TYPE《精密型无间隙 标准和减径管 在使用中的闷头三通配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 6043A-2012 FITTING TEE STANDARD AND REDUCER BULKHEAD ON RUN FLARELESS PRECISION TYPE《精密型无间隙 标准和减径管 在使用中的闷头三通配件》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD FITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, FLARELESS, PRECISION TYPE AS6043Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanica

2、l, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2009-12REVISED 2012

3、-07THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.AFEDERAL SUPPLY CLASS 4730 AS6043SHEET 1 OF 4REV. APROCUREMENT SPECIFICATION: /5/ AS18280SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is

4、entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, stabilized or cancelled.SAEinvi

5、tes yourwrittencommentsandsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6043ARATIONALE CORRECTED SIZE, -14 THREAD CORRECTED MATERIAL CODE LETTER W ANODIZE CORRECTED THREAD SPEC CORRECTED PORT #1 TUBE SIZE 08-06 C

6、ORRECTED HEAT TREAT FOR FOR W MATERIAL FIGURE 1 - FITTING, TEE, BULKHEAD END, PORT #3 SHOWN AS REDUCER FIGURE 2 - FITTING, TEE, BULKHEAD END, NON-REDUCER SHOWN, SAME AS FIGURE 1 EXCEPT AS SHOWN AEROSPACE STANDARD AS6043SHEET 2 OF 4REV. AFITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, FLARELESS,

7、 PRECISION TYPE TABLE 1 - DIMENSIONS AND WEIGHTS /9/ /10/ BASIC NO. AS6043/19/SIZE CODE V W LB/EAAPPROX REF ALUMLB/EAAPPROX REF STEELLB/EAAPPROX REF TI02 .297- .314 .090 .0185 .0531 .0293 03 .360- .377 .100 .0289 .0830 .0458 04 .423- .440 .110 .0373 .107 .0591 05 .485- .502 .120 .0498 .143 .0789 06

8、.547- .565 .120 .0612 .176 .0969 08 .735- .753 .150 .125 .358 .198 10 .860- .878 .170 .162 .466 .257 12 1.047-1.065 .185 .277 .798 .440 14 1.173-1.191 .200 .372 1.07 .590 16 1.292-1.317 .205 .400 1.15 .634 20 1.605-1.630 .240 .701 2.01 1.11 24 1.855-1.880 .250 .908 2.61 1.44 32 2.542-2.572 .350 1.95

9、 5.60 3.09 TABLE 2 - LEG LENGTH B /9/ /11/ FORGING SIZETUBE SIZE OF PORT #1 02 03 04 05 06 08 10 12 14 16 20 24 32 02 1.336 - - - - - - - - - - - - 03 1.367 1.414 - - - - - - - - - - - 04 1.413 1.460 1.523 - - - - - - - - - - 05 1.445 1.492 1.555 1.555 - - - - - - - - - 06 1.555 1.602 1.665 1.665 1.

10、711 - - - - - - - - 08 1.664 1.711 1.774 1.774 1.820 1.992 - - - - - - - 10 1.804 1.851 1.914 1.914 1.960 2.132 2.273 - - - - - - 12 1.914 1.961 2.024 2.024 2.070 2.242 2.383 2.492 - - - - - 14 2.024 2.071 2.134 2.134 2.180 2.352 2.493 2.617 2.543 - - - - 16 2.039 2.086 2.149 2.149 2.195 2.367 2.508

11、 2.617 2.617 2.617 - - - 20 2.320 2.367 2.430 2.430 2.476 2.648 2.789 2.898 2.898 2.898 2.898 - - 24 2.602 2.649 2.712 2.712 2.758 2.930 3.071 3.180 3.180 3.180 3.180 3.180 - 32 2.992 3.039 3.102 3.102 3.148 3.320 3.461 3.570 3.570 3.570 3.570 3.570 3.773 TABLE 3 - LEG LENGTH D /9/ /11/ FORGING SIZE

12、TUBE SIZE OF PORT #2 OR #3 02 03 04 05 06 08 10 12 14 16 20 24 32 02 .804 - - - - - - - - - - - - 03 .883 .930 - - - - - - - - - - - 04 .883 .930 .961 - - - - - - - - - - 05 .977 1.024 1.055 1.055 - - - - - - - - - 06 .992 1.039 1.070 1.070 1.086 - - - - - - - - 08 1.149 1.196 1.227 1.227 1.243 1.33

13、6 - - - - - - - 10 1.274 1.320 1.352 1.352 1.368 1.461 1.524 - - - - - - 12 1.335 1.383 1.414 1.414 1.430 1.523 1.586 1.649 - - - - - 14 1.398 1.445 1.476 1.476 1.492 1.585 1.648 1.742 2.023 - - - - 16 1.429 1.476 1.507 1.507 1.523 1.616 1.679 1.742 1.742 1.742 - - - 20 1.710 1.757 1.788 1.788 1.804

14、 1.897 1.960 2.023 2.023 2.023 2.023 - - 24 1.898 1.945 1.976 1.976 1.992 2.085 2.148 2.211 2.211 2.211 2.211 2.211 - 32 2.085 2.132 2.163 2.163 2.179 2.272 2.335 2.398 2.398 2.398 2.398 2.398 2.398 AEROSPACE STANDARD AS6043SHEET 3 OF 4REV. AFITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, FLARE

15、LESS, PRECISION TYPE TABLE 4 - TUBE SIZE AND CORRESPONDING THREAD PORT SIZE(NOMINAL TUBE SIZE)T THREAD PER AS 8879 02 .125 .3125-24 UNJF 03 .188 .3750-24 UNJF 04 .250 .4375-20 UNJF 05 .312 .5000-20 UNJF 06 .375 .5625-18 UNJF 08 .500 .7500-16 UNJF 10 .625 .8750-14 UNJF 12 .750 1.0625-12 UNJ 14 .875 1

16、.1875-12 UNJ 16 1.000 1.3125-12 UNJ 20 1.250 1.6250-12 UNJ24 1.500 1.8750-12 UNJ 32 2.000 2.5000-12 UNJ NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE./1/ MATERIAL: a. CODE LETTER T TYP

17、E 6AL-4V TITANIUM ALLOY PER PROCUREMENT SPECIFICATION b. CODE LETTER V TYPE 15-5PH, CORROSION RESISTANT STEEL PER PROCUREMENT SPECIFICATION c. CODE LETTER W TYPE 7075-T73 ALUMINUM ALLOY BAR OR FORGING, OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER PROCUREMENT SPECIFICATION 2. HEAT TREATMENT: a. MATERIAL

18、 CODE LETTER T ANNEALED PER PROCUREMENT SPECIFICATION b. MATERIAL CODE LETTER V AGE TO CONDITION H1075 PER PROCUREMENT SPECIFICATION c. MATERIAL CODE LETTER W ELECTRICAL CONDUCTIVITY AND HARDNESS PER PROCUREMENT SPECIFICATION /3/ FINISH: a. MATERIAL CODE LETTER T ANODIZE OR FLUORIDE PHOSPHATE CONVER

19、SION COAT PER PROCUREMENT SPECIFICATION b. MATERIAL CODE LETTER V: 1. V CODE PARTS TO BE PASSIVATED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: PASSIVATE PER PROCUREMENT SPECIFICATION 2. V CODE PARTS TO BE CADMIUM PLATED ONLY SHALL HAVE THE FINISH

20、 CODE LETTER “P” AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: CADMIUM PLATE PER PROCUREMENT SPECIFICATION c. MATERIAL CODE LETTER W ANODIZE PER PROCUREMENT SPECIFICATION /4/ OXYGEN SYSTEM AND COMPONENT CLEANING, SUFFIX LETTER A /19/: a. MATERIAL CODE LETTER P CLEAN AND PACKAGE PER ARP

21、1176 CATEGORY 1C b. MATERIAL CODE LETTER W CLEAN AND PACKAGE PER ARP1176 CATEGORY 2 AEROSPACE STANDARD AS6043SHEET 4 OF 4REV. AFITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, FLARELESS, PRECISION TYPE /5/ PROCUREMENT SPECIFICATION: AS18280 UNLESS OTHERWISE SPECIFIED ON THIS STANDARD. PRODUCT SU

22、PPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS18280 FOR THIS STANDARD. SEE http:/www.eAuditN FOR CURRENT QPL ONLINE. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN TUBING CONNE

23、CTION SYSTEMS WITH NOMINAL OPERATING PRESSURES AS SPECIFIED IN AS18280. ADDITIONAL CRITERIA - FOR REDUCER CONFIGURATIONS THE PRESSURE RATING IS DETERMINED BY THE LARGEST PORT. 7. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 8. WHEN MACHINING FROM BAR STOCK OR OVERSIZED FORGING, THE CENTER BO

24、DY DIMENSIONS SHALL CONFORM TO AS1376, TABLE 2. /9/ THE DIMENSIONS IN THE TABLES 1 THROUGH 4 ARE FOR FINAL MACHINED PARTS. THE FORGING SIZE IS DETERMINED AS THE SIZE NECESSARY TO MAKE THE LARGEST FITTING END. /10/ WEIGHTS ARE FOR NON-REDUCERS ONLY. REDUCER FITTINGS WILL HAVE LOWER WEIGHTS. /11/ REDU

25、CER FITTINGS WHICH FALL IN THE SHADED AREA OF TABLES 2 AND 3 SHOULD BE AVOIDED. IF THEY MUST BE USED, SPECIAL ATTENTION SHOULD BE GIVEN TO CLAMPING OR OTHER MEANS TO PROTECT THE SMALLER PORT OR TUBE. 12. FITTING IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS18280. 13. A CHANGE BAR ( l ) LOCATED IN TH

26、E LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CH

27、ANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 14. INTERPRETATION OF DRAWING PER ARP4296. 15. FLUID PASSAGE, HOLE CONTOUR PER ARP4266. 16. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIE

28、D, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra. 17. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 18. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 0 DEGREES 30 MINUTES. /19/ EXAMPLES OF PART NUMBERS: AS6043 V 08 08

29、 08 A NOTE: FOR THE SEQUENCE OF THE PORT NUMBERS IN THE PART NUMBER /19/ THE PORT #1 SHALL BE OF A LARGER SIZE OR OF THE SAME SIZE AS PORT #2. BASIC PART NUMBER MATERIAL CODE LETTER /1/ SIZE CODE FOR PORT 1 IN .062 INCREMENTS SIZE CODE FOR PORT 2 IN .062 INCREMENTS SIZE CODE FOR PORT 3 IN .062 INCREMENTS CODE LETTER FOR OXYGEN CLEANING. /4/ OMIT CODE LETTER IF OXYGEN CLEANING IS NOT REQUIRED. THE FINISH CODE LETTER “P” WILL BE PLACEDHERE ONLY FOR MATERIAL CODE LETTER “V PARTS THAT ARE TO BE CADMIUM PLATED. /3/ IF THE “P” IS USED, THE “A” CODE LETTER SHALL NOT BE USED.