SAE AS 24347-2001 DRUMS METAL REUSABLE SHIPPING AND STORAGE《FSC 8110可再用金属鼓的运输和贮存》.pdf

《SAE AS 24347-2001 DRUMS METAL REUSABLE SHIPPING AND STORAGE《FSC 8110可再用金属鼓的运输和贮存》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 24347-2001 DRUMS METAL REUSABLE SHIPPING AND STORAGE《FSC 8110可再用金属鼓的运输和贮存》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD DRUMS, METAL, REUSABLE SHIPPING AND STORAGE AS24347Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or ot

2、herwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2001-12REAFFIRMED 2017-11THIRD ANGLE PROJECTION CUST

3、ODIAN: EG-1 FEDERAL SUPPLY CLASS 8110 AS24347 SHEET 1 OF 4 PROCUREMENT SPECIFICATION: MIL-D-6055 SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sciences. The useof this report is entirely voluntary, and its applicabili

4、ty andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is the sole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and sugge

5、stions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS24347 RATIONALE AS24347 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS24347F AND CON

6、TAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS24347F. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGI

7、NAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED

8、GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MAN

9、DATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.AEROSPACE STANDARD AS24347 SHEET 2 OF 4 DRUMS, METAL, REUSABLE SHIPPING AND STORAGE NOTE: NUT AND BOLT FURNISH WITH TIN OR ZINC FLAKE/CHROM

10、ATE OR ELECTRO-PLATED ZINC; PLATED HEX HD 1/4-20 NC-2A X 1-1/2 LG BOLT THRD LGTH 1-1/2 IN., SCREWDRIVER SLOT 1/16 X 3/32 DP. WITH NUT OR 1/4-20 NC-2A X 1-1/2 LG. RD. HD. THRD LENGTH 1-1/2 SCREWDRIVER SLOT 1/16 X 3/32 DP. WITH NUT.SEE FOLLOWING SPECIFICATIONS.MIL-T-10727 (.0003 TO .0005 IN THICK)MIL-

11、C-87115 CLASS 3ASTM B633 TYPE II - OLIVE DRAB, SC-2AEROSPACE STANDARD AS24347 SHEET 3 OF 4 DRUMS, METAL, REUSABLE SHIPPING AND STORAGE COMPONENTS TABLE IITYPE OF CONSTRUCTION: BODIES MAY BE FORMED AS SHOWN IN TYPE I OR DRAWN AS SHOWN IN TYPE II. MS PART NUMBERS LISTED ARE FOR CLASS S (STEEL) FORMED

12、DRUM ASSEMBLY AND COMPONENTS. FOR CLASS A (ALUMINUM ALLOY) DRUM ASSEMBLY AND COMPONENTS, ADD AN A IN PLACE OF THE DASH IN THE PART NUMBER, I.E. MS24347A3 OR MS24347A51. WHEN ORDERING A DRAWN DRUM (TYPE II), ADD A SUFFIX D TO THE NUMBER, I.E. MS24347-4D OR MS24347A18D. MATERIAL: STEEL, ASTM-A366 BODY

13、, BOTTOM, AND COVER-5 INCH DIA DRUMS, 26 GAGE; 6-1/2 AND 8-1/2 INCH DIA DRUMS, 24 GAGE STEEL. ASTM-A109, LOCKING RING, 20 GAGE. LUGS, 14 GAGE. FOR ALUMINUM ALLOY, GASKETS, CUBIC CAPACITY, AND MARKING, SEE PROCUREMENT SPECIFICATION.NOTES: REFERENCED GOVERNMENT DOCUMENTS OF THE ISSUE LISTED IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATION AND STANDARDS (DODISS) SPECIFIED IN THE SOLICITATION FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN.FOR METRIC CONVERSION SEE TABLE IIIAEROSPACE STANDARD AS24347 SHEET 4 OF 4 DRUMS, METAL, REUSABLE SHIPPING AND STORAGE TABLE III