EN 12324-1-1998 en Irrigation Techniques - Reel Machine Systems - Part 1 Size Series《灌溉技术 轮机系统 第1部分 尺寸系列》.pdf

《EN 12324-1-1998 en Irrigation Techniques - Reel Machine Systems - Part 1 Size Series《灌溉技术 轮机系统 第1部分 尺寸系列》.pdf》由会员分享，可在线阅读，更多相关《EN 12324-1-1998 en Irrigation Techniques - Reel Machine Systems - Part 1 Size Series《灌溉技术 轮机系统 第1部分 尺寸系列》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Irrigation techniques - Reel machine systems - Part 1: Size series The European Standard EN 123241: 1998 has the status of a British Standard ICs 5.060.35 3s EN 12324-1:1999 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGH LAW STD-BSI BS EN L232i-L-ENGL A997 I lb2qb

2、b9 O7795b2 7Li7 direction of the Engineering AmdNo. Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 May 1999 BS EN 12324-1:1999 Date Text affected National foreword This British Stanird is the English language version of EN 123241: 1998. The

3、 UK participation in its preparation was entnisted to Technical Committee AGEBO, Irrigation and dramage equipment, which has the responsibility to: - aid enquirem to understand the text; - present to the responsible European committee any enquiries on the - monitor related international and European

4、 developments and promulgate interpretation, or proposals for change, and keep the UK interests informed; them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or Europea

5、n publications referred to in this document may be found in the BSI Standards Caalogue under the section entitled “Inteniationai Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessar

6、y provisions of a contsact. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages

7、2 to 6, an inside back cover and a back cover. O BSI 05-1999 ISBN O 680 32047 2 STD-BSI BS EN L232Y-L-ENGL 1999 m Lb24bb9 07795b3 b85 m EUROPEAN sI”DATI;D EN 123241 NO= EXJR0PEE”E EUROPISm NORM December 1998 ICs 65.060.35 Descriptors: irrigation, agricultural equipment, windings, water supply, water

8、 pipes, plastic pipes, polyethylene, specifications, dimensions, definitions, marking Enghsh version mon techniques- Reel madine systems - Part 1: size series lkchniques ciinigation - Installations avec emulem - Partie 1: Gammes dimensionelles Bewsserungsverfahren- Beregnungsmaschinen mit Fkgnereinz

9、ug - Teil 1: Baureihen This European Standard was approved by CEN on 18 November 1998. CEN members are bound to comply with the CENKENELEC Inkd Regulations which stipulate the conditions for giving this European Standard the status of a nationai standard without any aiteration. Uptodate lists and bi

10、bliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility

11、 of a GEN member into its own language and notified to the Centml Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, Fraizce, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands,

12、 Norway, Portugal, Spain, Sweden, Swizerland and Unit for reel machim. prEN 123243, Irrigation techniques - Reel machine systems - Part 3: Pre.sentatwn of technical chamterist.ics. prEN 123244, Irrigation techniques - Reel machine systems - Part 4: Check list for user requirements. prEN IS0 8224-1,

13、9avm irrigation machines - Part 1: Labomtory and field test muloh. Accordmg to the CENICENELEC Internal Regulations, the national standards organizations of the foiowing countries are bound to implement this European Standark Ausbia, Belgium, Czech Republic, Denmark, Finland, France, Gennanx Greece,

14、 Iceland, Ireiand, Italy, Luxembourg, Netherlands, Norway, Porhgal, Spain, Sweden, Switzerland and the United Kingdom. conflicting national standards shall be withdrawn at Contents Foreword 1 Scope 2 Nonnative references 3 Definitions 4 Specifications of the structures 5 Specifications applying to p

15、olyethylene tubes affixed to stsuctures 6 Marking Page 2 3 3 3 3 6 6 O BSI 05-1999 1 scope This part of prEN 12324 gives the dimensional specifications of the reel machine structures and of the corresponding polyethylene tubes. 2 Normative references This European Standard incorpomks by dated or und

16、ated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed heredter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when

17、incorporated in it by amendment or revision. For undated references the hest edition of the publication referred to applies. prEN 12324-2 1996, Irrigation tRchn2gues - Red machine systems - Part 2: SpcmJcatwns of polyethyh tubes for reel mhines. prEN 908, Agrimdtuml and forestry machinmy - Red machi

18、nes for irrigation - Safety. 3 Dentions For the purposes of this European Standard, the following definitions apply 3.1 reel machine type of traveller irrigation machine featuring a stationary structure with a reel, coiling a tube which carries irrigation water to, and drags a travelling cart upon w

19、hich is afked the distribution system, which is most often an irrigation gun NOTE A sketch showing the main parts of a reel machine and their names is given in Figure 1. 3.2 structure (ST) conventional designation for the various sizes of a reel machine frame, ailowing it to accommodate a polyethyle

20、ne tube for reel-machines, the diameter of which is listed in a range of polyethylene tubes, and the length of which conforms to specific conditions 3.3 polyethylene tube (for reel machine) one of the parts of a reel machine which COMS the cart to the structure ( c) external diameter of the polyethy

21、lene tube affixed on the machine; d) length and series of the polyethylene tube affixed on the machine. Example of marking: II xxx ST 5 - 1998 - no 0007654321 90 mm 350 m - S1 O BSI 05-1999 BS EN 123241:1999 BSI 389 Chwick High Road London w4 4AL BSI - British Standards Institution BSI is the indepe

22、ndent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure thai they

23、 possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuray or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the ide

24、ntity of which can be found on the inside front cover. Tel: 0181 996 9000. Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures tha subscribers automatidy receive the Mest editions of standars. Buying standards Orders for ail BSI, international and foreign

25、standards publications should be addressed to Customer Services. Tel 0181 996 9001. Fax: 0181 996 7001. In response to orderc for intrnational standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information

26、on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Inf

27、ormation Centre. Tek 0181 996 7111. Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel 0181 996 7002. Fax:

28、0181 996 7001. Copyright Copyright subsists in ail BSI publications. BSI also holds the copyright, in the UK, of the publications of the intemational standardization bodies. Except as perrniw under the Copyright, Designs and Patents Act 1988 no exh.act may be reproduced, stored in a retried system o

29、r txansmitted in any form or by any means - eleclxonic, photocopying, recording or otherwise - without prior written permission fiom BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, iype or grade designations. If these details are to be used for any other purpose than implementation then the prior Written permission of BSI must be obtained If permission is granted, the krms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel 0181 996 7070.