CEN TS 15398-2016 Resilient textile and laminate floor coverings - Floor covering standard symbols - Complementary element《弹性织物和层压地板覆盖物 地板覆盖标准符号 互补元素》.pdf

《CEN TS 15398-2016 Resilient textile and laminate floor coverings - Floor covering standard symbols - Complementary element《弹性织物和层压地板覆盖物 地板覆盖标准符号 互补元素》.pdf》由会员分享，可在线阅读，更多相关《CEN TS 15398-2016 Resilient textile and laminate floor coverings - Floor covering standard symbols - Complementary element《弹性织物和层压地板覆盖物 地板覆盖标准符号 互补元素》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationPD CEN/TS 15398:2016Resilient, textile and laminatefloor coverings Floorcovering standard symbols Complementary elementPD CEN/TS 15398:2016 PUBLISHED DOCUMENTNational forewordThis Published Document is the UK implementation of CEN/TS 15398:2016. It supersedes DD CEN/TS 15398

2、:2008 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/3, Textile floor coverings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provis

3、ions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 90535 3 ICS 01.080.20; 59.080.60; 97.150 Compliance with a British Standard cannot confer immunity from legal obligations.This British S

4、tandard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dPD CEN/TS 15398:2016TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 15398 January 2016

5、 ICS 01.080.20; 59.080.60; 97.150 Supersedes CEN/TS 15398:2008English Version Resilient, textile and laminate floor coverings - Floor covering standard symbols - Complementary element Revtements de sol rsilients, textiles et stratifis - Symboles normaliss de revtements de sol Elastische, textile und

6、 Laminat-Bodenbelge - Standardisierte Symbole fr Bodenbelge This Technical Specification (CEN/TS) was approved by CEN on 24 November 2015 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to su

7、bmit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is per

8、missible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Esto

9、nia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STAN

10、DARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 15398:2016 EPD CEN/TS 15398:2016CEN

11、/TS 15398:2016 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Descriptions and definitions of symbols 7 3.1 General 7 3.2 Classification according to EN ISO 10874 . 7 3.3 Pictograms related to essential requirements 10 3.3.1 General . 10 3.3.2 CE markin

12、g 10 3.3.3 Electrical behaviour 10 3.3.4 Fire. 11 3.3.5 Slip . 13 3.3.6 Water tightness . 14 3.3.7 Dangerous substances 14 3.3.8 Thermal resistance 15 3.4 Additional characteristics . 16 3.4.1 General . 16 3.4.2 Castor chair suitability . 16 3.4.3 Stairs suitability 16 3.4.4 Fraying behaviour 17 3.4

13、.5 Luxury classes . 17 3.4.6 Light fastness . 18 3.4.7 Acoustic properties . 18 3.4.8 Resistance . 19 3.4.9 Locking strength . 20 3.4.10 Swelling 21 3.4.11 Flexibility 21 3.4.12 Dimensional stability 21 3.4.13 Residual indentation . 22 3.4.14 Effect of a furniture leg . 22 3.4.15 Enhanced slip prope

14、rty 22 3.4.16 Suitability for use in incidental humid conditions . 23 3.4.17 Horizontal electrical resistance 23 3.4.18 Roll length and roll width . 24 3.4.19 Thickness characteristics 24 3.4.20 Tile size 25 3.4.21 Total mass . 25 3.4.22 Light reflection 25 3.5 Fibre composition (only of relevance f

15、or textile floorcoverings) 25 3.6 Underlays for laminate floorcoverings 28 3.7 Environmental Product Declaration . 29 Bibliography . 30 PD CEN/TS 15398:2016CEN/TS 15398:2016 (E) 3 European foreword This document (CEN/TS 15398:2016) has been prepared by Technical Committee CEN/TC 134 “Resilient, text

16、ile and laminate floor coverings”, the secretariat of which is held by NBN. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This docum

17、ent supersedes CEN/TS 15398:2008. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugo

18、slav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. PD CEN/TS 15398:2016CEN/TS 15398:2016 (E) 4 Intr

19、oduction Resilient, textile and laminate floor coverings and in case of floating installation with underlays, the combination of these floorcoverings with underlays, have a number of specific characteristics and are classified in a number of use classes. In order to make the classification and these

20、 specific characteristics understandable and recognizable to the consumer, graphic symbols have been developed. For practical reasons, only symbols for characteristics linked directly to a European or ISO Standard have been developed. Copyright: This document and these symbols are copyright protecte

21、d by CEN. The symbols may not be altered, changed in any way except size and colour. Similarly, no parts or elements of these symbols may be copied or redesigned in order to create new symbols not included in this document. These symbols can only be used when the product is tested or classified acco

22、rding to the related standard. PD CEN/TS 15398:2016CEN/TS 15398:2016 (E) 5 1 Scope This Technical Specification establishes a system of graphic symbols for use in the marking of the following floor coverings and specifies the use of these symbols: resilient floor coverings manufactured from plastics

23、, linoleum, cork or rubber, excluding loose-laid mats; textile floor coverings, excluding loose-laid mats; laminate floor coverings; floor panels for floating installation. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indisp

24、ensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 425, Resilient and laminate floor coverings - Castor chair test EN 438-1, High-pressure decorative laminates

25、 (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 1: Introduction and general information EN 660-2, Resilient floor coverings - Determination of wear resistance - Part 2: Frick-Taber test EN 669, Resilient floor coverings - Determination of dimensional stability of lino

26、leum tiles caused by changes in atmospheric humidity EN 717-1, Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method EN 717-2, Wood-based panels - Determination of formaldehyde release - Part 2: Formaldehyde release by the gas analysis method

27、 EN 985, Textile floor coverings - Castor chair test EN 986, Textile floor coverings - Tiles - Determination of dimensional changes due to the effects of varied water and heat conditions and distortion out of plane EN 994, Textile floor coverings - Determination of the side length, squareness and st

28、raightness of tiles EN 1081, Resilient floor coverings - Determination of the electrical resistance EN 1307, Textile floor coverings - Classification EN 1399, Resilient floor coverings - Determination of resistance to stubbed and burning cigarettes EN 1814, Textile floor coverings - Determination of

29、 resistance to damage at cut edges using the modified Vettermann drum test EN 1815, Resilient and textile floor coverings - Assessment of static electrical propensity EN 1963, Textile floor coverings Tests using the Lisson Tretrad Machine PD CEN/TS 15398:2016CEN/TS 15398:2016 (E) 6 EN 13329, Laminat

30、e floor coverings Elements with a surface layer based on aminoplastic thermosetting resins Specifications, requirements and test methods EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests EN 13553, Resilient fl

31、oor coverings - Polyvinyl chloride floor coverings for use in special wet areas - Specification EN 13745, Surfaces for sports areas - Determination of specular reflectance EN 13845, Resilient floor coverings - Polyvinyl chloride floor coverings with particle based enhanced slip resistance - Specific

32、ation EN 13893, Resilient, laminate and textile floor coverings - Measurement of dynamic coefficient of friction on dry floor surfaces EN 14041, Resilient, textile and laminate floor coverings - Essential characteristics EN 14215, Textile floor coverings - Classification of machine-made pile rugs an

33、d runners EN 14978, Laminate floor coverings - Elements with acrylic based surface layer, electron beam cured - Specifications, requirements and test methods EN 15468, Laminate floor coverings - Elements with directly applied printing and resin surface layer - Specifications, requirements and test m

34、ethods EN 16205, Laboratory measurement of walking noise on floors CEN/TS 16354, Laminate floor coverings - Underlays - Specification, requirements and test methods EN ISO 105-B02, Textiles - Tests for colour fastness - Part B02: Colour fastness to artificial light: Xenon arc fading lamp test (ISO 1

35、05-B02) EN ISO 354, Acoustics - Measurement of sound absorption in a reverberation room (ISO 354) EN ISO 717-2, Acoustics - Rating of sound insulation in buildings and of building elements - Part 2: Impact sound insulation (ISO 717-2) EN ISO 10874, Resilient, textile and laminate floor coverings - C

36、lassification (ISO 10874) EN ISO 11654, Acoustics - Sound absorbers for use in buildings - Rating of sound absorption (ISO 11654) EN ISO 14025, Environmental labels and declarations - Type III environmental declarations - Principles and procedures (ISO 14025) EN ISO 23997, Resilient floor coverings

37、- Determination of mass per unit area (ISO 23997) EN ISO 24340, Resilient floor coverings - Determination of thickness of layers (ISO 24340) EN ISO 24341, Resilient and textile floor coverings - Determination of length, width and straightness of sheet (ISO 24341) PD CEN/TS 15398:2016CEN/TS 15398:201

38、6 (E) 7 EN ISO 24342, Resilient and textile floor-coverings - Determination of side length, edge, straightness and squareness of tiles (ISO 24342) EN ISO 24344, Resilient floor coverings - Determination of flexibility and deflection (ISO 24344) EN ISO 24346, Resilient floor coverings - Determination

39、 of overall thickness (ISO 24346) EN ISO 26987, Resilient floor coverings - Determination of staining and resistance to chemicals (ISO 26987) ISO 1765, Machine-made textile floor coverings Determination of thickness ISO 6356, Textile and laminate floor coverings Assessment of static electrical prope

40、nsity Walking test ISO 8302, Thermal insulation Determination of steady-state thermal resistance and related properties Guarded hot plate apparatus ISO 8543, Textile floor coverings Methods for determination of mass ISO 10965, Textile floor coverings Determination of electrical resistance ISO 24334,

41、 Laminate floor coverings Determination of locking strength for mechanically assembled panels ISO 24338, Laminate floor coverings Determination of abrasion resistance ISO 24343 (all parts), Resilient and laminate floor coverings Determination of indentation and residual indentation 3 Descriptions an

42、d definitions of symbols 3.1 General If a specific standard is not valid for all three product groups, the relevant product group(s) will be mentioned below using one of the following abbreviations: T = Textile floor coverings; R = Resilient floor coverings; L = Laminate floor coverings. Where relev

43、ant the value of the technical characteristic needs to be given in the technical documentation. For example the pictogram for thermal resistance (Figure 35) should be accompanied by the value of the thermal resistance. 3.2 Classification according to EN ISO 10874 In EN ISO 10874 a classification sys

44、tem for different use classes is described, with references to the relevant product standards. In the following the pictograms, as defined in EN ISO 10874. PD CEN/TS 15398:2016CEN/TS 15398:2016 (E) 8 Figure 1 Class 21 Domestic moderate/light Figure 2 Class 22 Domestic general/medium Figure 3 Class 2

45、2+ Domestic general Figure 4 Class 23 Domestic heavy Figure 5 Class 31 Commercial moderate PD CEN/TS 15398:2016CEN/TS 15398:2016 (E) 9 Figure 6 32 Commercial general Figure 7 Class 33 Commercial heavy Figure 8 Class 34 Commercial very heavy Figure 9 Class 41 Industrial moderate Figure 10 Class 42 In

46、dustrial general PD CEN/TS 15398:2016CEN/TS 15398:2016 (E) 10 Figure 11 Class 43 Industrial heavy 3.3 Pictograms related to essential requirements 3.3.1 General EN 14041 specifies the health, safety and energy saving requirements of floor coverings under the CE marking. 3.3.2 CE marking Figure 12 CE

47、 mark (EU Regulation 765/2008/EC, Annex II) 3.3.3 Electrical behaviour The electrical behaviour of textile, laminate and resilient floor coverings antistatic floor covering - is specified in EN 14041 (R + L + T), EN 1815 (R+L), ISO 6356 (T). Figure 13 Electrical behaviour Antistatic floor covering T

48、he electrical behaviour of textile, laminate and resilient floor covering vertical resistance is specified in EN 14041(R+L+T), EN 1081 (R+L), ISO 10965 (T). Figure 14 Electrical behaviour Vertical resistance Static dissipative floor covering PD CEN/TS 15398:2016CEN/TS 15398:2016 (E) 11 Figure 15 Ele

49、ctrical behaviour Vertical resistance Conductive floor covering 3.3.4 Fire The reaction to fire of textile, laminate and resilient floor coverings is specified in EN 14041 (R+L+T) and EN 13501-1. Figure 16 Reaction to fire Class A1flFigure 17 Reaction to fire Class A2fl-s1 Figure 18 Reaction to fire Class A2fl-s2 PD CEN/TS 15398:2016CEN/TS 15398:2016 (E) 12 Figure 19 Reaction to fire Class Bfl-s1 Figure 20 Reaction to fire Class Bfl-s2 Figure 21 Reaction to fire Class Cf