ASTM E140-2012be1 7500 Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness Vickers Hardness Rockwell Hardness Superficial Hardness Knoop Hardness Scl.pdf
《ASTM E140-2012be1 7500 Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness Vickers Hardness Rockwell Hardness Superficial Hardness Knoop Hardness Scl.pdf》由会员分享,可在线阅读,更多相关《ASTM E140-2012be1 7500 Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness Vickers Hardness Rockwell Hardness Superficial Hardness Knoop Hardness Scl.pdf(25页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: E140 12b1Standard Hardness Conversion Tables forMetals Relationship Among Brinell Hardness, VickersHardness, Rockwell Hardness, Superficial Hardness, KnoopHardness, Scleroscope Hardness, and Leeb Hardness1This standard is issued under the fixed designation E140; the number immediately f
2、ollowing the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been ap
3、proved for use by agencies of the Department of Defense.1NOTEEq A10.1 and Eq A10.2 were editorially corrected in August 2013.1. Scope*1.1 Conversion Table 1 presents data in the Rockwell Chardness range on the relationship among Brinell hardness,Vickers hardness, Rockwell hardness, Rockwell superfic
4、ialhardness, Knoop hardness, and Scleroscope hardness of non-austenitic steels including carbon, alloy, and tool steels in theas-forged, annealed, normalized, and quenched and temperedconditions provided that they are homogeneous.1.2 Conversion Table 2 presents data in the Rockwell Bhardness range o
5、n the relationship among Brinell hardness,Vickers hardness, Rockwell hardness, Rockwell superficialhardness, Knoop hardness, and Scleroscope hardness of non-austenitic steels including carbon, alloy, and tool steels in theas-forged, annealed, normalized, and quenched and temperedconditions provided
6、that they are homogeneous.1.3 Conversion Table 3 presents data on the relationshipamong Brinell hardness, Vickers hardness, Rockwell hardness,Rockwell superficial hardness, and Knoop hardness of nickeland high-nickel alloys (nickel content over 50 %). Thesehardness conversion relationships are inten
7、ded to apply par-ticularly to the following: nickel-aluminum-silicon specimensfinished to commercial mill standards for hardness testing,covering the entire range of these alloys from their annealed totheir heavily cold-worked or age-hardened conditions, includ-ing their intermediate conditions.1.4
8、Conversion Table 4 presents data on the relationshipamong Brinell hardness, Vickers hardness, Rockwell hardness,and Rockwell superficial hardness of cartridge brass.1.5 Conversion Table 5 presents data on the relationshipbetween Brinell hardness and Rockwell B hardness of auste-nitic stainless steel
9、 plate in the annealed condition.1.6 Conversion Table 6 presents data on the relationshipbetween Rockwell hardness and Rockwell superficial hardnessof austenitic stainless steel sheet.1.7 Conversion Table 7 presents data on the relationshipamong Brinell hardness, Vickers hardness, Rockwell hardness,
10、Rockwell superficial hardness, and Knoop hardness of copper.1.8 Conversion Table 8 presents data on the relationshipamong Brinell hardness, Rockwell hardness, and Vickershardness of alloyed white iron.1.9 Conversion Table 9 presents data on the relationshipamong Brinell hardness, Vickers hardness, R
11、ockwell hardness,and Rockwell superficial hardness of wrought aluminum prod-ucts.1.10 Conversion Table 10 presents data in the Rockwell Chardness range on the relationship among Leeb (Type D)hardness, Brinell hardness, Vickers hardness, and Rockwellhardness of non-austenitic steels including carbon,
12、 alloy, andtool steels in the as-forged, annealed, normalized, andquenched and tempered conditions provided that they arehomogeneous.1.11 Many of the conversion values presented herein wereobtained from computer-generated curves of actual test data.Most Rockwell hardness numbers are presented to the
13、 nearest0.1 or 0.5 hardness number to permit accurate reproduction ofthese curves.1.12 Annex A1-Annex A10 contain equations to convertfrom one hardness scale to another. The equations given inAnnex A1-Annex A9 were developed from the data in Tables1 to 9, respectively. The equations given in Annex A
14、10 weredeveloped at the time the Leeb hardness test was invented (seeAppendix X2). The data in Table 10 was calculated from theAnnex A10 equations.1.13 Conversion of hardness values should be used onlywhen it is impossible to test the material under the conditionsspecified, and when conversion is ma
15、de it should be done withdiscretion and under controlled conditions. Each type of1These conversion tables are under the jurisdiction of ASTM Committee E28 onMechanical Testing and are the direct responsibility of Subcommittee E28.06 onIndentation Hardness Testing.Current edition approved Dec. 1, 201
16、2. Published May 2013. Originallyapproved in 1958. Last previous edition approved in 2012 as E140 12a. DOI:10.1520/E0140-12B.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United Sta
17、tes1hardness test is subject to certain errors, but if precautions arecarefully observed, the reliability of hardness readings made oninstruments of the indentation type will be found comparable.Differences in sensitivity within the range of a given hardnessscale (for example, Rockwell B) may be gre
18、ater than betweentwo different scales or types of instruments. The conversionvalues, whether from the tables or calculated from theequations, are only approximate and may be inaccurate forspecific application.2. Referenced Documents2.1 ASTM Standards:2A956 Test Method for Leeb Hardness Testing of St
19、eelProductsE10 Test Method for Brinell Hardness of Metallic MaterialsE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE92 Test Method for Vickers Hardness of Metallic Materials(Withdrawn 201
20、0)3E384 Test Method for Knoop and Vickers Hardness ofMaterialsE448 Practice for Scleroscope Hardness Testing of MetallicMaterials3. Methods for Hardness Determinations3.1 The hardness readings used with these conversion tablesshall be determined in accordance with one of the followingASTM test metho
21、ds:3.1.1 Brinell HardnessTest Method E10.3.1.2 Rockwell HardnessTest Method E18 ScalesA, B, C,D, E, F, G, H, K, 15-N, 30-N, 45-N, 15-T, 30-T, 45-T, 15-W.3.1.3 Vickers Hardness and Knoop HardnessTest MethodE384.3.1.4 Scleroscope4HardnessPractice E448.3.1.5 Leeb HardnessTest Method A956.NOTE 1The comp
22、arative hardness test done to generate the conver-sion tables in this standard were performed in past years using ASTM testmethods in effect at the time of testing. In some cases, the standards havechanged in ways that could affect the final results. For example, currentlyboth the Rockwell and Brine
23、ll hardness standards (Test MethodE10 andE18, respectively) allow or require the use of tungsten carbide ballindenters; however, all of the ball scale Rockwell hardness tests (HRB,HR30T, etc.) and most of the Brinell hardness tests preformed to developthese tables used hardened steel ball indenters.
24、 The use of tungsten carbideballs will produce slightly different hardness results than steel balls.Therefore, the user is cautioned to consider these differences and to keepin mind the approximate nature of these conversions when applying themto the results of tests using tungsten carbide balls.4.
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTME1402012BE17500STANDARDHARDNESSCONVERSIONTABLESFORMETALSRELATIONSHIPAMONGBRINELLHARDNESSVICKERSHARDNESSROCKWELLHARDNESSSUPERFICIALHARDNESSKNOOPHARDNESSSCLPDF

链接地址:http://www.mydoc123.com/p-526965.html