ASTM D7168-2005 Standard Test Method for99Tc in Water by Solid Phase Extraction Disk《用固相萃取盘测定水中99Tc的标准试验方法》.pdf

《ASTM D7168-2005 Standard Test Method for99Tc in Water by Solid Phase Extraction Disk《用固相萃取盘测定水中99Tc的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7168-2005 Standard Test Method for99Tc in Water by Solid Phase Extraction Disk《用固相萃取盘测定水中99Tc的标准试验方法》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 7168 05Standard Test Method for99Tc in Water by Solid Phase Extraction Disk1This standard is issued under the fixed designation D 7168; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A num

2、ber in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method describes a solid phase extraction(SPE) procedure to separate99Tc from environmental watersamples (that is, non-process

3、and effluent waters).Technetium-99 beta activity is measured by liquid scintillationspectrometry.1.2 This test method is designed to measure99Tc in therange of approximately 0.037 Bq/L (1.0 pCi/L) or greater for aone litre sample.1.3 The values stated in SI units are to be regarded asstandard. Value

4、s given in parentheses are provided for infor-mation purposes only.1.4 This method has been used successfully with tap water.It is the users responsibility to ensure the validity of this testmethod for samples larger than 1 L and for waters of untestedmatrices.1.5 This standard does not purport to a

5、ddress all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For specific hazardstatements, see Section 9.2. Refer

6、enced Documents2.1 ASTM Standards:2D 1129 Terminology Relating to WaterD 1193 Specification for Reagent WaterD 2777 Practice for Determination of Precision and Bias ofApplicable Methods of Committee D19 on WaterD 3370 Practices for Sampling Water from Closed ConduitsD 4448 Guide for Sampling Ground-

7、Water MonitoringWellsD 5847 Practice for Writing Quality Control Specificationsfor Standard Test Methods for Water AnalysisD 6001 Guide for Direct-Push Water Sampling for Geoen-vironmental Investigations3. Terminology3.1 DefinitionsFor definitions of terms used in this testmethod refer to Terminolog

8、y D 1129.4. Summary of Test Method4.1 Ameasured aliquant of sample is transferred to a beaker.Hydrogen peroxide is added to facilitate the formation of theextractable pertechnetate ion. The sample may be heated tooxidize organics if such are suspected to be present. The entiresample is passed throug

9、h a technetium-selective SPE disk ontowhich the pertechnetate is adsorbed. The disk is transferred toa liquid scintillation vial, cocktail added, and the contents wellmixed. The beta emission rate of the sample is determined byliquid scintillation spectrometry. Chemical yield correctionsare determin

10、ed by the method of standard additions.4.2 Minor differences in processing between ExtractionChromatographic Resin Discs and PTFE Membrane Disks areaddressed in Variations A and B of the method.5. Significance and Use5.1 This method has not been evaluated for all possiblematrices. Method suitability

11、 should be determined on specificwaters of interest.6. Interferences6.1 Suspended materials must be removed by filtration orcentrifuging prior to processing the sample. Suspended par-ticulate matter in the sample will be physically trapped in partor in whole on or in the SPE extraction material. Thi

12、s may leadto potential inclusion of radionuclide bearing solids or to signalquenching in the liquid scintillation measurement.6.2 Technetium-99 activity in the sample may overwhelmthe signal from the99Tc spike addition and interfere withaccurate determination of chemical yield. Samples for whichthe

13、unspiked sample count rate exceeds 50 % of the spikedsample count rate should be reprepared with an appropriatelyadjusted aliquant and spike addition levels to minimize contri-butions to uncertainty in the determination of the chemicalyield.6.3 Organic compounds present in significant quantities int

14、he sample may degrade the extraction performance of the SPEdisk or may lead to elevated levels of quench during liquidscintillation analysis. After the addition of hydrogen peroxide,the sample may be heated to destroy trace organic matter in the1This test method is under the jurisdiction of ASTM Com

15、mittee D19 on Waterand is the direct responsibility of Subcommittee D19.04 on Methods of Radiochemi-cal Analysis.Current edition approved June 1, 2005. Published June 2005.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For An

16、nual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.sample. If organic components are present in the sample whichmay survive t

17、he peroxide digestion, these may be removedwith an appropriate organic removal resin or disk (such asAmberchrom resin or disk) prior to passing the sample throughthe extraction chromatographic resin disc.6.4 The disk may retain tritium-labeled compounds. Settingthe99Tc counting window above the maxi

18、mum energy for thetritium beta particle will eliminate potential tritium interfer-ence.6.5 Elevated levels of nitrates ( 10 000 ppm) will interferewith uptake of99Tc.6.6 The higher energy region above the maximum energyfor99Tc should be monitored to help identify cases of signifi-cant actinide inter

19、ference.6.7 Elevated levels of radionuclides present in anionic formsuch as iodate, iron (III) and antimony may interfere withmeasurement of technetium and lead to a positive bias insample results. Significantly elevated levels of actinides(esp.234Th decay progeny of uranium) when present in thesamp

20、le may cause a high bias in the reported99Tc activity.Manufacturer specific recommendations about interferencesshould be taken into consideration when determining theapplicability of this method for a given matrix.7. Apparatus7.1 Filtering Apparatus, 47-mm diameter filter apparatus asrecommended by

21、the SPE manufacturer.7.2 Liquid Scintillation Counter, with multiple energy re-gion of interest (ROI) capabilities.7.3 Scintillation Vials, 20-mL vials, low potassium glass orplastic, exhibiting suitable optical reproducibility so as not tocause erratic results between samples.8. Reagents and Materi

22、als8.1 Purity of ReagentsReagent grade chemicals shall beused in all tests. Unless otherwise indicated, it is intended thatall reagents shall conform to specifications of the Committeeon Analytical Reagents of the American Chemical Society.3Other grades may be used, provided it is first ascertained

23、thatthe reagent is of sufficiently high purity to permit its usewithout lessening the accuracy of the determinations.8.2 Purity of WaterUnless otherwise indicated, referencesto water shall be understood to mean reagent water conformingto Specification D 1193, Type III.8.3 Radioactive PurityRadioacti

24、ve purity shall be suchthat the measured radioactivity of blank samples does notexceed the calculated probable error of the measurement.8.4 Technetium-Specific Solid Phase Extraction (SPE) Disksor Membranes (Extraction Chromatographic Resin Discs4orPTFE Membrane Disks4,5).8.5 Hydrochloric Acid, 0.5M

25、Add 42 mL concentratedHCl to 400 mL of reagent water. Dilute to 1 L with water.8.6 Nitric Acid, concentrated.8.7 Hydrogen Peroxide,30%.8.8 Technetium-99 as pertechnetate in water or dilute basesolution, traceable to a national standards body (such as NISTin the U.S.).8.9 Liquid Scintillation Cocktai

26、lCommercially preparedLSC cocktail or equivalent.4,69. Hazards9.1 Use extreme caution when handling all acids. They areextremely corrosive, and skin contact could result in severeburns.9.2 When diluting concentrated acids, always use safetyglasses and protective clothing, and add the acid to the wat

27、er.10. Sampling10.1 Collect a sample in accordance with Practice D 3370,D 4448 or D 6001.11. Preservation11.1 Preservation of samples being analyzed for99Tc is notrequired.11.1.1 Samples may be preserved by freezing. Allowsamples to come to ambient temperature prior to processing.11.1.2 Samples may

28、be processed if they have been previ-ously preserved to pH less than 2 with nitric or hydrochloricacid. It is noted that high concentrations of nitric acid willadversely affect chemical yield.Although yield corrections willcorrect for losses, better results may be obtained by usingunpreserved sample

29、s.12. Calibration12.1 The fractional detector efficiency (eTc) is determined asoutlined in subsequent steps.12.1.1 Prepare triplicate calibration samples adding at least20 Bq (540 pCi) of traceable99Tc in the pertechnetate form toeach of three 100 mL portions of reagent water. Each of thethree sampl

30、es is processed using either method variation (A orB), as appropriate.3Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For suggestions on the testing of reagents notlisted by the American Chemical Society, see Annual Standards for Laboratory and

31、National Formulary, U.S. Pharmaceutical Convention, Inc. (USPC), Rockville,MD.4The sole source of supply of the Eichrom TEVAt Discs known to thecommittee at this time is Eichrom Technologies, Inc., Darien, IL. If you are awareof alternative suppliers, please provide this information to ASTM Internat

32、ionalHeadquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee,1which you may attend.53M Emporey Tc Rad Disks (3M, St. Paul, MN) have been found satisfactoryfor this purpose.6Ultima Goldy LLT (Perkin Elmer Life and Analytical Sciences, 710 Brid

33、ge-port Avenue, Shelton, CT 06484-4794) has been found satisfactory for this purpose.D716805212.1.2 Collect the effluents from the three calibrationsamples. Process the composited solution according to themethod to verify that greater than 99 % of the technetium wasretained by the SPE material in th

34、e calibration runs.12.1.3 An analyte-free aliquant of 100 mL reagent water isalso processed as a calibration or instrument blank.12.1.4 Count the three vials containing the calibrationsamples and the blank in a liquid scintillation counter for a timesufficient to amass greater than 10 000 counts for

35、 each of thecalibration standards.12.1.5 Calculate the99Tc Detector Efficiency (eTc) for eachof the three vials:eTc5Rg2 RcbAc(1)where:Rg= gross count rate of the vial in the99Tc count windowin counts per second,Rcb= count rate of the calibration blank associated withthe efficiency measurement in the

36、99Tc count win-dow in counts per second, andAc= activity of standard99Tc added to each vial (Bq).12.2 Calculate the average, eTc, and the relative standarddeviation, sr(eTc), for the three efficiency values. The relativestandard deviation of these parameters is used to estimate therelative standard

37、uncertainty of the average efficiency, ur(eTc),as follows:ureTc! 5sr2eTc!31 ur2Ac! (2)where:ur(Ac) = relative standard uncertainty of the activity ofstandard99Tc added to each vial.12.3 Acalibration blank consisting of reagent water shall beprocessed and analyzed with each batch of samples to deter-

38、mine the background count rate in counts per second (Rb)tobeused for the calculation of sample results.13. ProcedureNOTE 1To minimize the risk of cross-contamination while ensuringreproducibility between the sample and its spiked duplicate, each aliquant-spiked aliquant pair should be run simultaneo

39、usly and in parallel, usingseparate dedicated filtration apparatus.NOTE 2The sample aliquant is typically 1 L but depending on theactivity present and the required detection limit for the analysis, this mayvary from 0.1 to several litres.NOTE 3A representative instrument blank (vial, cocktail and bl

40、ankdisk) is counted with each batch to determine the background count rateto be subtracted from each measurement (Rbin Eq 3). If the instrumentblank is to be reused, the user should determine its stability and shelf-life.13.1 Method Variation AFor use with Extraction Chro-matographic Resin Discs:13.

41、1.1 For each sample to be processed, transfer duplicate 1L aliquants of sample to each of two beakers.13.1.2 Acidify samples to pH 2 with nitric acid, if not donepreviously.13.1.3 Add a known quantity (20 Bq) of a traceable99Tcsolution to the second aliquant of the sample which is labeledas the spik

42、ed sample. (See section 6.2 for comment onappropriate spiking level.)13.1.4 Add 10 mL of 30 % H2O2to each sample whilestirring.13.1.5 If the presence of organic interferences is suspected,heat the sample on a hotplate at approximately 80C for about1 hour or until any visible reaction has subsided. A

43、llow thesample to cool to ambient temperature before proceeding withsubsequent steps.13.1.6 Using forceps, carefully position a disc on the filterstand. Secure the funnel reservoir over the disc.13.1.7 Precondition the disc by allowing 25 mL of water topass through the disc by gravity.13.1.8 Add the

44、 sample to the funnel reservoir and allow topass through the disc by gravity flow (nominal flow rate shouldnot exceed 100 mL/min).13.1.9 Rinse the disc with 25 mL of 0.5M HCl.13.1.10 Rinse the disc with 100 mL of water.13.1.11 Apply vacuum to the filtration apparatus to removeresidual liquid from th

45、e disc.13.1.12 Detach the reservoir from the filter apparatus.13.1.13 Using forceps, remove and carefully roll the discand transfer to a scintillation vial.13.1.14 Add 15 mL of liquid scintillation cocktail.13.1.15 Cap and shake the contents of the vial, to allow thedisc to disintegrate. A vortex mi

46、xer may be used.13.1.16 Count the sample in a liquid scintillation counterusing an optimized energy window within the range of 20 to292 keV for a period of time adequate to achieve the requireddetection limit.13.2 Method Variation BFor use with PTFE ExtractionMembranes:13.2.1 For each sample to be p

47、rocessed, transfer duplicate 1L aliquants of sample to each of two beakers.13.2.2 Add a known quantity (20 Bq) of traceable99Tcsolution to the second aliquant of the sample which is labeledas the spiked sample. (See section 6.2 for comment onappropriate spiking level.)13.2.3 Add 10 mL of 30 % H2O2to

48、 each sample whilestirring.13.2.4 If the presence of organic interferences is suspected,heat the sample on a hotplate at approximately 80C forapproximately 1 hour or until any visible reaction has subsided.Allow the sample to cool to ambient temperature beforeproceeding with subsequent steps.13.2.5

49、Using forceps, carefully position a disk on the filterstand. Secure the funnel reservoir over the disk.13.2.6 Connect the filtering apparatus to a vacuum source.13.2.7 Pass the sample through the disk at a nominal flowrate of 100 mL/min.13.2.8 Rinse the disk with 25 mL of 0.5M HCl.13.2.9 Rinse the disk with 100 mL of water.13.2.10 Detach the reservoir from the filter apparatus.13.2.11 Using forceps, remove and gently roll the disk andtransfer to a scintillation vial.13.2.12 Add 15 mL of liquid scintillation cocktail.D716805313.2.13 Cap and shake the contents o