ASTM A671-2006 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures《常温和较低温用电熔焊钢管的标准规范》.pdf
《ASTM A671-2006 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures《常温和较低温用电熔焊钢管的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM A671-2006 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures《常温和较低温用电熔焊钢管的标准规范》.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: A 671 06Standard Specification forElectric-Fusion-Welded Steel Pipe for Atmospheric andLower Temperatures1This standard is issued under the fixed designation A 671; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the y
2、ear of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification2covers electric-fusion-welded steelpipe with filler metal added, fabricated from pressure
3、vesselquality plate of several analyses and strength levels andsuitable for high-pressure service at atmospheric and lowertemperatures. Heat treatment may or may not be required toattain the desired properties or to comply with applicable coderequirements. Supplementary requirements are provided for
4、use when additional testing or examination is desired.1.2 The specification nominally covers pipe 16 in. (405mm) in outside diameter or larger and of14 in. (6.4 mm) wallthickness or greater. Pipe having other dimensions may befurnished provided it complies with all other requirements ofthis specific
5、ation.1.3 Several grades and classes of pipe are provided.1.3.1 Grade designates the type of plate used as listed in 5.1.1.3.2 Class designates the type of heat treatment performedduring manufacture of the pipe, whether the weld is radio-graphically examined, and whether the pipe has been pressurete
6、sted as listed in 1.3.3.1.3.3 Class designations are as follows (Note 1):Class Heat Treatment on Pipe Radiography,see SectionPressure Test,see:10 none none none11 none 9 none12 none 98.313 none none 8.320 stress relieved, see 5.3.1 none none21 stress relieved, see 5.3.1 9 none22 stress relieved, see
7、 5.3.1 9 8.323 stress relieved, see 5.3.1 none 8.330 normalized, see 5.3.2 none none31 normalized, see 5.3.2 9 none32 normalized, see 5.3.2 9 8.333 normalized, see 5.3.2 none 8.340 normalized and tempered, see 5.3.3 none none41 normalized and tempered, see 5.3.3 9 none42 normalized and tempered, see
8、 5.3.3 9 8.343 normalized and tempered, see 5.3.3 none 8.350 quenched and tempered, see 5.3.4 none none51 quenched and tempered, see 5.3.4 9 none52 quenched and tempered, see 5.3.4 9 8.353 quenched and tempered, see 5.3.4 none 8.360 normalized and precipitation heattreatednone none61 normalized and
9、precipitation heattreated9 none62 normalized and precipitation heattreated98.363 normalized and precipitation heattreatednone 8.370 quenched and precipitation heattreatednone none71 quenched and precipitation heattreated9 none72 quenched and precipitation heattreated98.373 quenched and precipitation
10、 heattreatednone 8.3NOTE 1Selection of materials should be made with attention totemperature of service. For such guidance, SpecificationA 20/A 20M maybe consulted.1.4 The values stated in inch-pound units are to be regardedas the standard.2. Referenced Documents2.1 ASTM Standards:3A 20/A 20M Specif
11、ication for General Requirements forSteel Plates for Pressure VesselsA 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 435/A 435M Specification for Straight-Beam UltrasonicExamination of Steel PlatesA 530/A 530M Specification for General Requirements forSpecialized Carbon a
12、nd Alloy Steel PipeA 577/A 577M Specification for Ultrasonic Angle-BeamExamination of Steel PlatesA 578/A 578M Specification for Straight-Beam UltrasonicExamination of Plain and Clad Steel Plates for SpecialApplicationsE110 Test Method for Indentation Hardness of MetallicMaterials by Portable Hardne
13、ss Testers1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel, and Related Alloys and is the direct responsibility of SubcommitteeA01.09 on Carbon Steel Tubular Products.Current edition approved May 1, 2006. Published May 2006. Originallyapproved in 1972. Las
14、t previous edition approved in 2004 as A 671 04.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-671 in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Boo
15、k of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.E 165 Test Metho
16、d for Liquid Penetrant ExaminationE 709 Guide for Magnetic Particle Examination2.2 Plate Steels:A 203/A 203M Specification for Pressure Vessel Plates, Al-loy Steel, NickelA 285/A 285M Specification for Pressure Vessel Plates,Carbon Steel, Low- and Intermediate-Tensile StrengthA 299/A 299M Specificat
17、ion for Pressure Vessel Plates,Carbon Steel, Manganese-SiliconA 353/A 353M Specification for Pressure Vessel Plates, Al-loy Steel, 9 Percent Nickel, Double-Normalized and Tem-peredA 515/A 515M Specification for Pressure Vessel Plates,Carbon Steel, for Intermediate- and Higher-TemperatureServiceA 516
18、/A 516M Specification for Pressure Vessel Plates,Carbon Steel, for Moderate- and Lower-Temperature Ser-viceA 517/A 517M Specification for Pressure Vessel Plates, Al-loy Steel, High-Strength, Quenched and TemperedA 537/A 537M Specification for Pressure Vessel Plates,Heat-Treated, Carbon-Manganese-Sil
19、icon SteelA 553/A 553M Specification for Pressure Vessel Plates, Al-loy Steel, Quenched and Tempered 8 and 9 % NickelA 736/A 736M Specification for Pressure Vessel Plates,Low-Carbon Age-Hardening Nickel-Copper-Chromium-Molybdenum-Columbium and Nickel-Copper-Manganese-Molybdenum-Columbium Alloy Steel
20、2.3 ASME Boiler and Pressure Vessel Code:4Section II, Material SpecificationsSection III, Nuclear VesselsSection VIII, Unfired Pressure VesselsSection IX, Welding Qualifications3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 lota lot shall consist of 200 ft (61 m) or fractiont
21、hereof of pipe from the same heat of steel.3.1.2 The description of a lot may be further restricted bythe use of Supplementary Requirement S14.4. Ordering Information4.1 The inquiry and order for material under this specifica-tion should include the following information:4.1.1 Quantity (feet, metres
22、, or number of lengths),4.1.2 Name of material (steel pipe, electric-fusionwelded),4.1.3 Specification number,4.1.4 Grade and class designations (see 1.3),4.1.5 Size (inside or outside diameter, nominal or minimumwall thickness),4.1.6 Length (specific or random),4.1.7 End finish (11.4),4.1.8 Purchas
23、e options, if any (see 5.2.3 and 11.3 of thisspecification. See also Specification A 530/A 530M),4.1.9 Supplementary requirements, if any.5. Materials and Manufacture5.1 MaterialsThe steel plate material shall conform to therequirement of the applicable plate specification for the pipegrade ordered
24、as listed in Table 1.5.2 Welding:5.2.1 The joints shall be double-welded, full-penetrationwelds made in accordance with procedures and by welders orwelding operators qualified in accordance with the ASMEBoiler and Pressure Vessel Code, Section IX.5.2.2 The welds shall be made either manually or auto
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMA6712006STANDARDSPECIFICATIONFORELECTRICFUSIONWELDEDSTEELPIPEFORATMOSPHERICANDLOWERTEMPERATURES 温和

链接地址:http://www.mydoc123.com/p-459120.html